-
product
Non Contact H,V. Detector
277 HP
Standard Electric Works Co., Ltd
● 2 ranges for selection ( 2 function buttons ) LOW : 50V~1.5kV Press the LOW button, 277 HP is ready for low voltage detection. HIGH : 1.5kV~132kV Press the HIGH button, 277 HP is ready for high voltage detection.● Power consumption: Off : Less than 5uA Low voltage detection mode: Less than 40mA High voltage detection mode: Less than 40mA● Circuit test function Press the Test button to make sure the whole circuit is working well before testing actual high voltage circuits.● Optional accessory: HS-175 Telescopic hot stick (triangle-type) HS-120 Hot stick
-
product
Analogue (1kV below) Insulation Tester
2132 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test. ● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
product
Ethernet Service Testing
Artiza Networks offers compact Ethernet service testing devices for Carrier/Metro Ethernet service providers. The GEST-1K and XEST-1 are fast and lightweight, and don’t require a technician to install.
-
product
PXI 8-slot BRIC Power Multiplexer, 24-Channel, 6-Pole (5 Sub-cards)
40-571A-403
The 40-571A-403 is a 24-channel, 6-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
Partial Discharge Testing Equipment
PD-Analyser
This is an ‘All in One’ solution for testing and analysing partial discharges in the insulation of high-voltage transformers, cables, GIS and electric machines. The DIMRUS ‘PD Analyser’ help diagnose their insulation state and find any type of defects very effectively.It can be used for temporary or constant monitoring of partial discharge in medium and high voltage systems and cables of any rated voltage.The PD Analyser is the most useful device for condition estimation of high-voltage insulati...show more -
product
OpenBenchmarking.org
OpenBenchmarking.org is an open, collaborative testing platform. The OpenBenchmarking.org infrastructure provides public and private storage of test result data (including system logs) and effective collaboration tools for sharing results and efficiently comparing multiple test result sets. OpenBenchmarking.org also provides a package management system for making accessible new, updated, and third-party test profiles / suites to the users of the Phoronix Test Suite.
-
product
Programmable High Power DC Power Supply
ADG series
Preen’s ADG series is a programmable DC power supply with high power density and high output power, and offers many great advantages on response time, accuracy and output voltage range. ADG is an excellent source for testing or facility type applications, such as aerospace, renewable energy, automated test system, battery and server. With power level up to 80kW per unit, the ADG series provides output voltage up to 1000V and high output current of 2000A after custom modification.
-
product
Switching Test Set
U3020AS26
The Keysight U3020AS26 is a switch matrix that consists of two single-pole-six-throw (SP6T) switches. It allows switching of multiple signal paths without physically changing the connections. This allows multiple tests to be performed with the same setup, eliminating the need for frequent connects and disconnects. An entire testing process can be automated, increasing the throughput in high-volume production environments.
-
product
PCBA Pattern Analyzer
A222918
The test method in the PCBA mainboard production line today mainly depends on the operator judgment. It is "subjective" testing and the accuracy decreased when the operator works for a long time.
-
product
Modbus Master Data Scanner
ModScan
ModScan is a Windows application which operates as a modbus master. It allows you to access and change data points in a connected slave device using either the RTU or ASCII Transmission mode. ModScan is ideally suited for quick and easy compliance testing of the modbus protocol and its built-in display of serial traffic allows effective troubleshooting of field connections.
-
product
Diode Scanner
SC924
Frothingham Electronics Corporation
The SC924 is an electromechanical device for testing diodes loaded on burn-in boards.A set of Kelvin contacts is indexed from diode to diode. The contacts move over a range of 24 inches in the X direction and the table holding the boards moves over a range of 9 inches. This allows scanning of multiple burn-in boards or boards with multiple rows of diodes.
-
product
SCT IFCC Self Test Box
MS 3647I
SCT-IFCC Self-Test Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has testing facility of all Inputs and outputs of Single channel tester of IFCC.
-
product
Partial Discharge Test System
TPP
The Partial Discharge Test System type TPP is used for non-destructive insulation and quality testing of electrical components (for example according VDE 0110-1, EN 50178, IEC 60270 and IEC 60060).
-
product
FibreSeek | PON Power Meter
TP40
Testing in the FTTx environment just got easier with Yamasaki’s latest piece of PON Test Equipment, the TP40 FiberSeek FTTx PON Power Meter. The TP40 includes FTTH PON Testing, 6 Wavelength Optical Power Meter & Visible Fault Identifier all in one unit. This rugged hand held unit includes a removable rubberized boot; bright backlit LCD; auto shut off function; wide measurement range; upstream burst mode; accurate testing and bright flashing VFI.
-
product
Guardian Hipot Analyzer
19055
Chroma Systems Solutions, Inc.
Hipot or dielectric withstand testing instruments manufactured by Chroma are used for conducting electrical safety tests on electrical components and products to make certain they are in compliance with IEC, UL, TUV, CSA, EN and other electrical safety requirements. In addition, these instruments are designed for general product or component testing as well as complex medical safety testing (60601-1) ensuring human safety and product reliability.
-
product
MTM-DAQ-2: 16-Channel Analog DAQ Module
PRECISION ANALOG MEASUREMENTS: The MTM 16-Channel MTM-DAQ-2 Data Acquisition (DAQ) Module is engineered for precision measurements of analog voltages in manufacturing or R&D testing.
-
product
WR3.4 Frequency Extension Solution, 220-330 GHz with VDI Extender Modules
CobaltFx 220 to 330 GHz
CobaltFx cost-effective millimeter wave frequency extension system allows you to build a scalable and affordable 5G testing solution.
-
product
Acoustic Emission Testing Equipment
1283 USB AE Node
The 1283 USB AE Node is a full-featured, low-cost Acoustic Emission testing equipment that plugs conveniently into and is powered by the USB port of a user’s PC or laptop to maximize portability and versatility.
-
product
Biofuels Testing and Inspection
Intertek delivers assurance, testing, inspection and certification services to refiners, producers, blenders, distributors, consumers and research institutes across the world.
-
product
IsatData Pro Physical Layer Tester
DPLT
Square Peg Communications Inc.
The IsatData Pro Physical Layer Tester (DPLT) supports testing of the physical layer performance and protocol implementation of Mobile Terminals (MTs) implementing Inmarsat’s IsatData Pro (IDP) services.
-
product
Probes And Accessories
Choose from a broad portfolio of Tektronix probes and accessories, all perfectly matched to our industry-leading oscilloscopes. With over 100 choices available, select the oscilloscope probe you need for your specific testing application. Download our Probe Selector Guide here.
-
product
PCIe Mono Industrial Camera
CMOSIS CMV2000
2K camera Applications: In-situ optical inspection camera, fast process capturing, e.g. Golf club swings, Intelligent Transportation Systems (ITS), Open road tolling and Traffic monitoring, Industrial Automation, Machine Vision, Facial Recognition, Motion Capture, Automotive crash testing, OCR/ OCV, 3D scanning, Robotic Arms, Material and Life science Microscopy, Ophthalmology and Retinal imaging, Medical Imaging, Flat panel inspection, Dental, Kiosks, Security, Biometrics
-
product
Temperature Test Chambers & Humidity Test Chambers
Weiss Technik Temperature & Humidity test chambers offer many pre-engineered and custom sizes to fit your exact testing requirements. Available models include a wide range of temperature ramp rates, humidity levels, and many standard and optional features including temperature cycling, steady-state testing, and fast change rate.
-
product
Bond Tester for Wafers 2 - 12 inch
Sigma W12
Bondtester for wafers or at wafer level 2” – 12” (up to 300 mm)Precise testing and Cold Bump Pull (CBP) testingLarge X/Y stages X: 600mm, Y: 370 mmForce range from 1gf – 10 kgfBump pitch down to 20 µm
-
product
Mixed Signal Automated Tester
MSAT
Whether you are testing radar systems for the Department of Defense (DoD), or the next actuator circuit card for aircraft landing systems, ARC’s Mixed Signal Automated Tester (MSAT) offers flexible automated testing capabilities for nearly every budget.
-
product
Oscilloscopes
AEMC Instruments proudly introduces the first hand-held portable two- and four-isolated-channel 600V Cat. III Oscilloscopes on the market with 12-bit resolution. Featuring five complimentary tools in one - an Oscilloscope, FFT Analyzer, TRMS Multimeter, Harmonic Analyzer and a Recorder - all in a rugged and ergonomic hand-held instrument. They are the perfect tools for both laboratory and field testing.
-
product
Material Testing & Physical Testing
Meeting the specifications put out by testing equipment manufacturers is critical when conducting quality control testing. We carry a wide variety of materials testing and physical testing products that are ideal for quality control testing along with research applications, letting you evaluate and test materials such as plastics, coatings, and chemicals. Physical properties testing products range from force and torque instruments, to hardness and thickness gauges, to viscometers and spectrometers.
-
product
Hardness Testers
Dalian Taijia Technology Co.,Ltd
Digital durometer for shore hardness testing pocket size model with integrated probe● Test scale: shore hardness● Standards: DIN53505, ASTMD2240, ISO7619, JISK7215● Parameters displayed: hardness result, average value, max. value● Measurement range:0-100HA(HD)(HC)● Measurement deviation:＜1%H● Resolution: 0.1● Auto switch off● With RS232C interface● Operating conditions: 0℃ to 40℃● Power supply: 4x1.5V AAA (UM-4) battery● Battery indicator: low battery indicator● Dimensions: 162x65x38mm● Weight (...show more -
product
PXI 8-slot BRIC Power Multiplexer, 8-Channel, 6-Pole (3 Sub-cards)
40-571A-401
The 40-571A-401 is a 8-channel, 6-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
4 Wire Earth Resistance Testers
4234 ER
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Earth testing at 2Ω, 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test.● 3-Wire test.● 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● Robust, compact and easy-to-carry.
