RS232
A standard interface for serial binary data interchange defining voltage levels for logical one and logical zero, standard transmission speed and connector types.
See Also: Serial Communications, I2C, RS422, RS485
-
product
Dual Input Digital Handheld Oscilloscope
SDM 760
Dual Input Digital Oscilloscope ; 20MHz. Dual Input Digital Multimeter ; AC/DC Volt, Frequency. Interface ; RS-232 Optically isolated. Operating time ; 2 hours with backlight. Charging time ; 12 hours
-
product
MODEM ELIMINATOR
The UDC-ME allows two DTE devices (such as routers) to communicate within proximity of each other. The UDC-ME transmits data bi-directionally at clock rates of 1.2k up to 3.072Mbps between DTE devices. The unit is equipped with two interface slots that allow a host of serial interface cards to be utilized. The serial interface cards available are RS-232, RS-422/449, RS-530, X.21, V.35 and HSSI. The Serial Interface cards are interchangeable and may be mixed such as RS-232 to V.35 thus eliminating the need for an interface converter or changing expensive serial cards on a DTE device such as a router.
-
product
IRIG B to NTP/SNTP Converter
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
product
PCIe/104 OneBank Carrier for Trenz SoC Modules
EMC²-DP
Sundance Multiprocessor Technology Ltd.
The EMC²-DP is a PCIe/104 OneBank™ Carrier for a Trenz compatible SoC Module and has expansion for a VITA57.1 FMC™ LPC I/O board and also has I/O pins, using a 100-way Samtec RazorBeam connectors system. The add-on board, called “Sundance External Interface Connector – SEIC” contains LEDs, RS232, USB2.0, HDMI, 1Gb Ethernet and SATA . The “SEIC” can be customize for individual applications and bespoke connectors.
-
product
ARM LPC3250 Board
MS 1509
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
product
Function Generator
FG-72
* 0.3Hz~7MHz* Hz.KHz.MHz..3Range, Easy Operation.* LED: 0.56", 6 Digits.* 2 Attenuator: (-20dB x 2)* RS-232 (or USB) Built-In.* PC Control: Frequency, Waveform, -20dB Attenuator.* Accuracy: 10PPM, Longtiome: ±1ppm/year* Waveform: Sine, Square, Triangle to 7MHz
-
product
50000 Counts Triple Display
SUMMIT192/194
50000 Counts Triple Display. 51 Segments Analog Bar Graph. Backlight & RS-232 Interface. True-RMS (50kHz). Capacitance (Max 20mF) & Inductance. (Max 300mH) ? Conductance & AC + DC. 192(CATIII 600V), 194(CATIV 600V)
-
product
- RS-232 to RS-422/RS-485 Converter
Model 285
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; Intelligent Control Of RS-485 Transmitter And Receiver; TD & RD LED's; DTE/DCE Compatible; Data Rates Up to 64 KBPs. The Model 285 RS-232 to RS-422/RS-485 Converter is a unique interface converter that can be configured to operate in compliance with RS-485 or RS-422 equipment, and RS-232.
-
product
Dual-Port Serial Interface Cards
PCI-COM2S And PCI-422/485-2
The PCI-COM2S and PCI-422/485-2 are dual-port, asynchronous serial communications cards designed for use in PCI-Bus computers. They are 6.5 inches (165 mm) long and may be installed in any 5V PCI slot in IBM and compatible computers. Each independent port supports RS-422 and RS-485 balanced-mode transmission/reception, and on the PCI-COM2S, RS-232 single-ended transmission/reception as well.
-
product
Voltage Datalogger
S5011
Data logger is designed for record of voltage. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper adapter.
-
product
Programmable Serial Device
HR-16P
The HR-16P is a programmable RS-232 serial device designed to control any device with a serial port based on sensing level changes (open-to-close and close-to-open, or digital high to low and vice versa).
-
product
RS232/422 Strobe Mux III Card & Panel
9565-32
32 serial port ISA compatible card connected by 4.8 ft (1.5m) cable and terminated as male DB25 connectors on external panel 14.5" high x 13" wide x 1" deep (645 x 330 x 25 mm).
-
product
Handheld Laser Power & Energy Meter
Vega 7Z01560
*Compatible with all standard Ophir Thermopile, BeamTrack, Pyroelectric and Photodiode sensors*Brilliant color large size TFT 320x240 display*Clear screen color for work with laser safety goggles*Illuminated keys for working in the dark*Both digital and analog needle display*USB and RS232 output to PC with Statistics package*Select between English and Japanese interfaces*Analog output*Soft keys and menu driven functions with on line help*Log every data point at up to 4000Hz with pyroelectric sensors*Non-volatile data storage up to 250,000 points*Laser tuning screen and power log*2 position kickstand*System Integrator Tools included: LabVIEW VIs, COM Object Interface
-
product
RS-232 to RS-422 Interface Converter
Model 253
FEATURES: DB9 Data Port; Compatible with PC/386/486; Full Duplex; Surge Protection. Adding an RS-422 interface to a PC is now a snap. The Model 253 Interface Converter does this for full duplex signals at data rates up to 19.2 KBPS, without requiring any AC or DC power. With only TD, RD and ground, the Model 253 provides operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
product
RS485 Null-Modem Cable, DB-9 Female to DB-9 Female, 4m
183283-04
9-Pin Female DB-9 to 9-Pin Female DB-9 Serial Cable - The 9F-9F Serial Cable, sometimes referred to as GPIB Serial Cable, connects and controls GPIB devices using RS232 and RS485 serial ports. The 9F-9F Serial Cable is offered in different lengths.
-
product
AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems
Chroma Systems Solutions, Inc.
Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.
-
product
SIMRC - 16-Channel 1-Pole Multiplexer
1020-R-16-1-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
SoftLine
When connecting two Network Interfaces together over a network or over the Internet, a virtual four wire audio line is created. Along with the audio line you get an RS232 connection and some I/O-ports.
-
product
Pico-ITX
RSB-3430
*Arm Cortex A9 NXP i.MX6 2.5" SBC*1 full HD HDMI, 2 ch. LVDS*1 RS-232/422/485, 1 GbE, 2 USB*M.2 & Mini-PCIe for the wireless expansion*UIO40-Express expansion supports 4USB, 2UART, 1UART/CAN, 12GPIO 1I2C
-
product
CPCI Avionics Bus Card
Avionics Bus Card is high end ARM core based MILBUS Communication Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have MIL1553B, ARINC429, CCDL, digital I/O interface, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board is based CPCI architecture and can be used with CPCI or PXI backplane. Rear IO Board is used to interface all IO’s of the board from Rear Side.
-
product
Physical Layer Switching Systems for copper LAN, WAN, DSL, Telco apps with RJ style connectors.
RJ Series
The RJ Series of computer controlled switching systems are designed for physical layer switching of multiwire signals on RJ style connectors. Since the system uses mechanical relays it acts exactly like a piece of cable which makes it perfect for testing networks without altering the signals or regeneration. These systems are typically used for Ethernet LAN 10BaseT through 1000BaseT, DSL including ASML through GFAST, CAT5 through CAT6A cable testing, USB up to 2.0, RS232, RS422, RS485 up to 8 wire at 20 Mbps and many other applications switched over RJ45 connectors up to 8 wires. They may also be used as lab automation switches, network testing switches, patch panels, network redundancy switches or any number of physical layer applications.
-
product
ZIO Module With Two COM Ports And 32 Bit Programbale DIO
AX93285
*Specification: 2 x RS-232, 32-bit programmable DIO*Dimension: 80 x 55 mm*Compliant Product: CAPA840, CAPA843, CAPA880, CAPA500, CAPA313
-
product
DIGITAL MULTIMETER 3 3/4
IBL-19RS
International Biological Laboratories
This is a 3-3/4 Digits 3999 Counts with anunciator Autoraning Professional Digital Multimeter with the facility for PC interface to download all the measuring data to the PC through RS-232 PC Interface.
-
product
Fanless Embedded System With Intel® Core™ I5-6300U 2.4 GHz/i3-6100U 2.3 GHz/Celeron® 3955U 2.0 GHz, 2 HDMI, 2 GbE LANs, 4 USB 3.0, 2 COM And 9 - 36 VDC
eBOX565-500-FL
The eBOX565-500-FL is designed to support the 6th generation Intel® Core™ i5-6300U or Celeron® 3955U processor with one 260-pin DDR4-2133 SO-DIMM socket with up to 16GB system memory. The eBOX565-500-FL is designed for reliable use in industrial environments with an IP40-rated enclosure, a wide range 9 to 36 VDC power input, a wide temperature ranges from -10°C to 50°C (14°F to 122°F), as well as up to 3G vibration endurance. To fulfill various needs, the palm-sized industrial embedded computer, which measures 141.6 x 106 x 73 mm in size, provides rich I/O connectivity including two HDMI ports, one RS-232/422/485 port, one RS-232 port, four USB 3.0 ports, two Gigabit Ethernet ports, and two SMA type connector openings for antenna. One PCI Express Mini Card slot enables the addition of Wi-Fi, 3G, or LTE wireless cards.
-
product
cRIO-9034, 1.91 GHz Quad-Core CPU, 2 GB DRAM, 16 GB Storage, and Kintex-7 325T FPGA, 4-Slot CompactRIO Controller
783453-01
1.91 GHz Quad-Core CPU, 2 GB DRAM, 16 GB Storage, and Kintex-7 325T FPGA, 4-Slot CompactRIO Controller - The cRIO-9034 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. Additionally, the cRIO-9034 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
Control Unit
Epec 3610
Epec 3610 Control Unit is a compact controller containing 22 I/O pins, all of them can be configured as input pins. Epec 3610 has an RS-232 serial port and as an assembly variant, I/O interface that is compatible with the previous Epec 2038 Control Unit. However, Epec 3610 also comes with completely new features like high-side current measurement and an internal 3-axis accelerometer, for example, for levelling purposes. Epec 3610 also has an option for accurate Pt1000 measurement.
-
product
ccXMC-Serial
Conduction Cooled XMC module with 16 differential IO and 12 RS-232 IO plus Spartan VI 100 FPGA. Industrial Temp. SOSA pinout. Initial design has 2 HDLC, 2 NRZ, and 3 UART ports implemented.
-
product
PXI Dual 18 Channel MUX, 96-Pin SCSI Connector
40-735-912-S1
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
product
GPIB-RS232, Instrument Control Device - Swiss 220VAC
779732-02
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a … talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Component Test Scanner
Model 13001
Support component test scanningSupport 8 slots for plug-in (removable), up to 320 channels for one unitOption A130007 40 channels scan module, input up to 500VDC for IR test without switchingMax. 8 salve units for multiple scanner (master/slave interface)Support Chroma LCR meterSupport Chroma 3302/3252/11025 turn ration functionSupport 11200 CLC/IR meter for IR testStandard RS-232, GPIB and USB interface13001 can be installed in Chroma Component ATE model 8800Support ICT applications
