Sensor Amplifiers
-
Product
Capillary-fill sensors
-
Zimmer and Peacock have launched the world's first capillary fill sensor for the Research and Development market, both academia and industry. We provide these capillary-fill sensors in gold, platinum and carbon.
-
Product
Operational Amplifier
Op Amp Series
-
The amplifier is capable of operating at supply voltages from 0.9V to 3V with specified specs at 1V and 1.8V single supply.The input common mode range extends to both power supply rails without the offset glitch and input bias current phase reversal inherent to most rail to rail input amplifiers.
-
Product
Broadband Amplified Noise Modules
NC2000/4000 Series
-
The NC2000 Series amplified noise modules are an excellent choice for high-level noise modules mounted on a circuit board. The NC2000 Series modules are housed in 24, or14-pin dual-inline packages. The NC4000 series modules are housed in a 40-pin module that cover similar noise bands to the NC2000, but have higher crest factor, and 60 dB of TTL controlled attenuation.
-
Product
1×6 Video Distribution Amplifier
VDA206 S-Video
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
-
Product
Rail-to-Rail Op Amplifiers
-
Analog Devices high speed (> 50 MHz) rail-to-rail op amps enable you to operate at lower supply voltages, swing closer to the rails, and provide wider dynamic range. Featuring a portfolio with a wide variety of op amps, including both rail-to-rail input/output as well as just rail-to-rail output, ADI provides the widest portfolio of leading edge products available on the market. Whether it is wide bandwidth, high slew rate or low distortion, or rail to rail, no one sets more performance standards for next generation designs than Analog Devices.
-
Product
Alfa Romeo Oxygen Sensor
KS60113 - Alfa Romeo
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
Optical Sensors: Fluorometers
-
Sea-Bird Scientific offers a wide variety of fluorometer configurations and measurement capabilities. ECO fluorometers are available in single, dual, and three-measurement combinations. Fluorometers measure chlorophyll-a, FDOM, rhodamine, phycocyanin, and phycoerythrin.
-
Product
Sensors
-
Panasonic Industrial Devices Sales Company of America
Panasonic Sensor Solutions offer a wide and constantly evolving range of technologies that provide design engineers with the flexibility to easily choose and implement the Sensor technology best suited for existing and ever-emerging new applications all from a single, world class supplier. Panasonic built-in Sensors contribute to energy savings, safety and comfort. With high-functionality and high-performance, Panasonic has solutions for sensing and detecting rotational speed and angle, position, flow, velocity, temperature, magnetism, currents and much more! Panasonic Sensor products combine the latest technologies with plug-and-play devices such as Grid-EYE® Thermopile Array Sensors, the Ultrasonic Gas Flow Sensor, the highly accurate and flexible 6in1 Sensor (6DoF Automotive Inertial Sensor), a wide array of Passive Infrared Motion Sensors (PIRs), and highly specialized and accurate Industrial Sensors.
-
Product
Optical Fiber Sensors
-
Optical sensors based on Fiber Bragg technology (FBG) are a reliable and safe solution for numerous testing applications, such as in structural testing and lightweight construction. Benefit from perfectly-matched measurement chains when using an optical FBG sensor based on Fiber Bragg Gratings made by HBM FiberSensing.
-
-
Product
GaN Power Amplifiers > 5W
-
Macom Technology Solutions Holdings Inc.
MACOM GaN RF power amplifier solutions are designed with the latest GaN-on-SiC and GaN-on-Si technologies. Our MACOM PURE CARBIDE series of GaN-on-SiC power amplifiers offers high performance and reliability for the most demanding applications. Our expanding GaN portfolio is designed to address the challenging requirements of Aerospace & Defense, Industrial, Scientific and Medical applications and 5G wireless infrastructure. MACOM GaN products deliver output power levels ranging from 2 W to over 7 kW and exhibit best in class RF performance with respect to gain and efficiency. For sensitive Aerospace & Defense applications MACOM can offer a US only supply chain with AS9100D Certification.
-
Product
Headphone Amplifier
MH-8
-
High-power headphone amplifier that distributes the stereo input to eight headphone outputs
-
Product
Panel-mounted Power Amplifier For Network Simulators
PAV250Bi
-
PAV250Bi is one of the conventional voltage power amplifier model, which is specially designed for R&D of power system simulation.
-
Product
Conformal Ballistic Pressure Sensor
Model: 117B67
-
Conformal ballistics pressure sensor, 22 WMRF, 22 WRF, 22 WRF WITH 0.50" Centerline, 17 RF Mag, 17 HMRConformal ballistics pressure sensor for 17 HMR, 17 Magnum RF, 17 RF Magnum, 22 WMRF, 22 WRF, and 22 WRF with 0.50" centerline caliber cartridges.
-
Product
Modal Exciters & Amplifiers
-
Experimental modal analysis, or modal testing, is a process for physically obtaining a math model of a structure’s dynamic properties. Modal tests identify a structure’s modal properties: natural frequencies, mode shapes, mass, stiffness and damping. Modal test results help troubleshoot resonant excitation from operating forces, validate and verify finite element models, predict the benefits of structural modifications, support design verification, and understand structural responses due to complex loading conditions.
-
Product
Oxygen Purity Sensors
-
At Process Sensing Technologies (PST) we specialize in offering replacement electrochemical oxygen sensors compatible with major fixed and portable oxygen analyzers, specifically tailored for enriched oxygen applications. PST’s oxygen purity sensors are designed to deliver unparalleled accuracy, ensuring optimal performance in diverse industrial settings.
-
Product
LPWAN Wireless Sensor Nodes
-
The WISE-2210 series features LPWAN CT current sensors, enabling efficient monitoring of electrical currents with low-power, long-range capabilities.
-
Product
Optical Speed Sensors
-
Allows use in a wide range of hazardous environments in petrochemical, Gas and volatile materials processing industries, ideally suited for Condition Monitoring, Data collectors in balancing applications, these sensors give excellent performance with repeatable results, engineered for easy mounting with the optional Mounting Bracket and Mini Tripod Stand in hand held applications.
-
Product
High-Speed System Synchronization and Distribution Amplifier - 3U VPX
Model 5903
-
- Multi-board synchronization with Quartz RFSoC video- Synchronizes up to 64 channels across eight Quartz® boards- Synchronizes sampling and data acquisition for multichannel systems- Provides single sample accurate synchronization between multiple channels and multiple boards- Synchronizes gating and triggering functions
-
Product
Non-contact Displacement Sensors
-
This is a flexible sensor that can be installed anywhere and is equipped with high environmental resistance enabling use in harsh environments.
-
Product
RF Bidirectional Amplifiers
-
Miniature, high-efficiency and linear bidirectional amplifier modules (transmit and receive). 1.0 to 2.5 GHz, automatic or manual T/R switching, high-efficiency or high-linearity models. Custom designs available through RF PA design services.
-
Product
Audio Amplifiers
-
An electronic device that increases the strength (amplitude) of audio signals that pass through it.
-
Product
Measuring Amplifiers
-
Smart force measurement with a parameterizable measurement amplifier.
-
-
Product
Position Sensors
-
A Position sensor is any type of device which detects the movement of a chosen object in either a Linear or Rotary motion and converts the movement into output signals which are suitable for processing, transmission or control depending on the application.
-
-
Product
UVA Logger Sensor
NUL-232
-
There are different wavelengths of ultra violet light.The UVA wavelength range is 320-370 nm, which is 98% of the total UV radiation.The UVA radiation affects photoaging and also photochemical smog.The intensity of this light is measured in mW/m2 (milliwatt per square meter).
-
Product
Instrument Grade Data Sensor
WISER 8000
-
TECAT Performance Systems, LLC
The TECAT WISER Model 8000 dual strain measurement and monitoring system is a wireless data acquisition system for measuring two external strain channels at high data rates up to 8kHz. The small, light, power-efficient, and non-invasive design enables strain measurements in a wide range of applications. With dual external sensor inputs two Micro-Measurements strain gauge bridges can be measured by a single system, for example to measure both thrust and torque loads simultaneously.The Model 8000 has a long range data transmission of >1,000 meters with up to +/- 0.025% FSR sensitivity for remote measurements. After initial setup using the WISER software interface, the system can be wired directly to your DAQ system, for seamless data collection.
-
Product
Proximity Sensors
-
A sensor able to detect the presence of nearby objects without any physical contact.
