Showing results: 901 - 915 of 1234 items found.
-
A025CFR-025CFR-5A100 -
Pickering Interfaces Ltd.
This 1m long female to female 25-Pin Micro-D Cable Assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port.
-
Extech DV23 -
Extech Instruments Corporation
Use DV23 to quickly check for the presence of live wires before performing any electrical testing. Suitable for outlets or against wire insulation testing, this AC Voltage Detector for non-contact detection of AC Voltage from 50 to 600V (50/60Hz). Red LED indicates the presence of voltage. Comes with two AAA batteries.
-
Shenzhen Everbest Machinery Industry Co.,Ltd.
Non-contact detection of 50 to 1000V ACRugged and double molded caseSuitable for outlets or against wire insulation testingFlashing red LED light indicatorBuilt-in bright flashlight with on/off buttonConvenient size with pocket clipAuto power offSystem self testUse on 50/60Hz circuitsComplete with two AA batteriesCATIII 1000VDimensions: 158 x 21mmWeight: 48g
-
2678X -
Shenzhen Chuangxin Instruments Co., Ltd.
Ground Earth Resistance Tester verifies the integrity (continuity) of the protective bonding of the equipment (Class I equipment) designed to secure safety through the basic insulation and protective earthing. It is also called earth (ground) bonding test. If the continuity of the protective bonding is confirmed, we can conclude that the equipment has the requirements for preventing electric shock even if the insulation between the primary circuit and the accessible conductive section fails and a fault current flows through the distribution system.
-
LXinstruments GmbH
Insulated test booth with large space for test items. 2 banana sockets for AC connection and 4 banana sockets for the DC connection of the DUTs. IC’s are tested in a long-term test. These are checked in an oil bath so that there are no air gaps to reduce the insulation. Maximum voltage 20 kV. Therefore, insulation tests must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.
-
TF-100 -
R&J Measurement
The measuring device Franklin tester is designed to measure the insulation resistivity of coating and its mineral components on the surface of electrotechnical steel sheet as well as applied enamel to generator stator core laminations according to the ASTM A717/ A717 M - 95 Standard. The device contain series connection which allow the data transmittion to PC.
-
Techsquare -
Techimp HQ S.r.L
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
Extech MG302 -
Extech Instruments Corporation
The Extech MG302 is a Wireless True RMS Multimeter with a built in insulation resistance tester. By adding insulation testing capabilities to this CAT IV-rated digital multimeter, electrical troubleshooters will always be equipped for the job. The digital insulation resistance tester, or megohmmeter, comes with four different test voltages for measuring resistance up to 4G Ω with 0.001 MΩ resolution. The multimeter also includes useful extras like duty cycle measurements, milliamp readings, and a built-in wireless data recording for safer troubleshooting and maintenance on moving equipment. The MG302 is waterproof (IP67-rated) and comes with a remote USB receiver, Windows compatible software, test leads with alligator clips, Type K bead wire temperature probe with adapter, carrying case, six AA batteries, and a user manual.
-
VE2882A-5U -
Vasavi Electronics
Impulse Tester can detect turn & layer short ,the differences in the number of turns and the material of the core. If high impulse voltage is applied, the poor insulation will appear as a corona or layer discharge.
-
CCI
*High power handling 500W per port with High in-band insulation at 30 dB minimum and 32 dB typical*Very low PIM <-160 dBc with low insertion loss*Outdoor rated unit with DC/AISG input pass through on all ports*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
Series 115 -
Pickering Electronics
SoftCenter construction Highest quality instrumentation grade switches Plastic package with internal mu-metal magnetic screen They take up the minimum of board area, conservingboard space Insulation resistance greater than 1E12 Ohms 100% tested for dynamic contact resistance for guaranteed performance 5 or 12 Volt coils with optional internal diode
-
Panasonic Industrial Devices Sales Company of America
A Commercialized PhotoIC Coupler For High-Speed Communication Between Industrial Equipment. Panasonic, a worldwide leader in cutting-edge electronic components, has developed and introduces the NEW APS1 Series PhotoIC Coupler that transmits light signals while allowing electrical insulation. This revolutionary new product is designed for high-speed transmission of signals between industrial equipment such as motors and PLCs.
-
A100SMR-100SMR-9A050 -
Pickering Interfaces Ltd.
This 0.5m long male to male 100-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28 AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for use with Pickering BRIC modules that use the 100-pin Micro-D connector.
-
A100SMR-100SMR-9A200 -
Pickering Interfaces Ltd.
This 2m long male to male 100-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28 AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for use with Pickering BRIC modules that use the 100-pin Micro-D connector.
-
A100SMR-100SMR-9A100 -
Pickering Interfaces Ltd.
This 1m long male to male 100-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28 AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for use with Pickering BRIC modules that use the 100-pin Micro-D connector.