Network Analyzers
software and/or hardware, that measures the activity on a network and the devices connected to the network.
See Also: Network, Vector Network Analyzers, Electrical Network Analyzers, Optical Network Analyzers, Portable Network Analyzers, Power Network Analyzers, Radio Network Analyzers, Scalar Network Analyzers, Wireless Network Analyzers, Impedance Analyzers
-
Product
Automatic Calibration Module
ACM2509
-
ACM2509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full two-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to seven connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
Product
120 GHz Frequency Extender, Pulsed DC Bias
N5295AX52
Frequency Extender
The N5295AX52 is a compact and broadband frequency extender with built-in pulsed bias-tee and provides 10 MHz to 120 GHz single-sweep measurements with N5292A test set controller systemized with a PNA/PNA-X B vector network analyzer.
-
Product
PXIe Vector Network Analyzer, 10 MHz To 44 GHz
M9837A
Vector Network Analyzer
The M9837A PXI network analyzer (VNA) offers unrivaled performance for testing multiport, multisite, multi-DUT modulated signal measurement from 10 MHz to 44 GHz.
-
Product
Lightwave Detector
N4377A
-
The N4377A Lightwave Detector is a USB-powered optical-electrical converter with built-in optical power meter capability. If used with a vector network analyzer or a spectrum analyzer it enables frequency domain applications in photonics.
-
Product
PXIe Network Analyzer Direct Access Receiver
M9377A
Vector Network Analyzer
The M9377A is one port PXIe Vector Network Analyzer direct access receiver which is used in the M9485A PXIe Multiport Vector Network Analyzer
-
Product
PXI Vector Network Analyzer, 9 kHz to 9 GHz
M9802A
Vector Network Analyzer
Full 2/4/6/ port VNA on a PXI module with flexible applications.
-
Product
RF Electronic Calibration Module (ECal), DC/300 KHz To 7.5 GHz, 7-16, 2 Port
85098D
-
The Keysight 85098D RF electronic calibration (ECal) module makes the calibration of vector network analyzers fast, easy, and accurate. ECal is a precision, single-connection calibration technique for your vector network analyzer. Performing a full two-port calibration takes less than half the time and a number of connections using ECal versus mechanical calibration kits. Furthermore, the accuracy of the calibration is comparable between electronic and mechanical methods. Traditional mechanical calibrations require intensive operator interaction, which is prone to errors. With ECal, the operator simply connects the ECal module to the network analyzer and the software controls the rest.
-
Product
Streamline Vector Network Analyzer, 9 KHz To 6.5 GHz, 4 Or 6-port
P5021B
Vector Network Analyzer
Compact, faceless, vector network analyzer (VNA). Flexible four or six-port VNA dramatically reduces your size of test. Up to 6.5 GHz.
-
Product
PXIe Vector Network Analyzer, 100 kHz to 53 GHz
M9808A
Vector Network Analyzer
Full 2 port VNA on a PXI module with flexible applications.
-
Product
6GHz 2-port Vector Network Analyzer
VNA-0460
-
The VNA-0460 is a full bi-directional 2-port Vector Network Analyzer that is controlled from a PC through a USB connection.
-
Product
RF Ports Alignment Software
-
With the R&S®RF Ports Alignment software together with the option R&S®SMW-K545, Rohde & Schwarz provides a standard and tailored solution for calibrating amplitude, time and phase of multi-channel SMW setups. The RF Port Alignment automatically collects the gathered correction data for the multi-channel setup using a connected vector network analyzer such as the R&S®ZNA or R&S®ZNB. Thanks to an intuitive graphical user interface the test engineer is guided through the calibration procedure step-by-step in a convenient way. With a calibrated multi-channel setup, tests of advanced systems in wireless communication or of radar receivers can be performed straightforward.
-
Product
Accessory Kit, Type-N to BNC, 50 Ohms
11854A
-
The Keysight 11854A accessory kit furnishes the RF components required for measurement of devices with 50 ohm, BNC connectors and when using a network analyzer with a type-N configuration. The BNC accessory kit contains two type-N male to BNC female adapters, two type-N male to BNC male adapters, two type-N female to BNC female adapters, two type-N female to BNC male adapters, a BNC male short, and a storage case.
-
Product
FieldFox Handheld RF Vector Network Analyzer
N9923A
Vector Network Analyzer
4/6 GHz max frequency Carry the world's most accurate handheld RF T/R VNA analyzer Expand capabilities with optional 2-port VNA, time-domain, vector voltmeter, cable and antenna analyzer and more Save time by simultaneously measuring all four S-parameters (S11, S21, S12, S22) with a single connection Perform accurate testing with QuickCal, full 2-port unknown thru Cal, TRL Easily measure average and puls
-
Product
PXIe Vector Network Analyzer, 100 kHz to 26.5 GHz
M9805A
Vector Network Analyzer
Full 2 port VNA on a PXI module with flexible applications.
-
Product
Fast-CW Measurements
S93118B
-
S93118B Fast-CW mode is a software capability to perform FIFO (first-in-first-out) data acquisition for fast measurement on PNA/PNA-L/PNA-X Series B model network analyzers.
-
Product
Ultra Low Noise Preamp
J2180A
-
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
Product
Automatic Calibration Module
ACM2506
-
ACM2506 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 6.5 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process.
-
Product
Spectrum Analysis For P50xxB Up To 20 GHz
S970904B
-
Add spectrum analysis to your P50xxB Streamline series vector network analyzer
-
Product
Spectrum Analysis For P50xxB Up To 53 GHz
S970908B
-
Add spectrum analysis to your P50xxB Streamline series vector network analyzer
-
Product
26.5 GHz Single-Mode Lightwave Component Analyzer
N4375E
-
The new N4375E single-Mode LCA is based on the latest 5222A series network analyzers with 2-port or 4-port configuration. This LCA is the ideal measurement solution for electro-optical components up 26.5GHz electro-optical components, as well as Radio over Fiber (RoF) and aerospace and defense (A&D) electro-optical test applications. The N4375D is traceable to international standards and provides guaranteed specifications for electro-optical responsively S-parameter measurements in a turn-key solution. In combination with N4691B electronic calibration kit you get fastest setup of your test, so you can focus on developing your components. The new N4375D replaces the industry standard 8703A/B series and supports specified modulation frequencies up to 26.5 GHz at 1310nm and 1550nm source wavelength or individual wavelength with external optical input.
-
Product
Electrical Network Analyzer
SHARK 200
-
*Compact design*Class 0.2 in energy, typical accuracy 0.1%*Front serial port for programming once installed*Integrated RS-485 (Modbus and DNP 3.0 protocols)*Self-range in voltage and current
-
Product
PXIe Performance Vector Signal Analyzer: 50 GHz
M9393A
Vector Network Analyzer
9 kHz to 8.4 GHz, 14 GHz, 18 GHz, or 27 GHz Frequency extension to 50 GHz (minimum frequency of 3.6 GHz) with Option FRX40 MHz (standard), 100 MHz, or 160 MHz analysis bandwidth, and optional wideband IF output with Option WB1Up to 4 time-synchronous channels
-
Product
Vector Network Analyzer (VNA) Simulator – Advanced
S94051B
Vector Network Analyzer
S94051B puts Keysight’s industry-leading network analyzer software portfolio into your computer. Dive deeper into data captured on an instrument with support for time domain, spectrum analysis, gain compression, and all the other software applications you use on your instrument. You can also develop and troubleshoot test programs on your computer before deploying them to the instrument. S94051B is a superset of S94050B and contains the S-parameter functionality.
-
Product
Frequency Extension Calibration Kits
FEK
-
Farran’s FEK-xx-0001 calibration kit provides accurate calibration of the Vector Network Analyzer (VNA). It is compatible with TRL and SOLT calibration techniques and allows for a full 12-term port calibration.
-
Product
PNA Microwave Network Analyzer
N5221B
Network Analyzer
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
NanoVIP® TWO™
-
NANOVIP® TWO™ is a modern, powerful, portable network analyzer developed for professional analysis of consumption and power quality of the most complex electrical networks.It can be used on single-phase, two-phase, three-phase (3 or 4 wires balanced) networks, low and medium voltage.
-
Product
4-Port 9 GHz Analyzer, Frequency Extension Compatible
C4409
-
C4409 Vector Network Analyzer delivers industry-leading dynamic range and sweep speed, with all the features engineers have come to expect included standard in our software. This VNA is frequency extender compatible and is the anchor network analyzer for the CobaltFx frequency extender system.
-
Product
Millimeter-wave Operation With Frequency Extenders For P50xxA Streamline VNA
S97560B
Vector Network Analyzer
Configure an affordable millimeter-wave banded VNA using P50xxA Streamline USB VNAs with this software
-
Product
Signal Integrity Evaluation up to 26.5 GHz
N5222BT
Network Analyzer
The N5222BT provides the N5222B 26.5 GHz PNA, application software including PLTS and enhanced TDR, and accessories for signal integrity evaluation of cables, backplanes and BGA packages.
-
Product
Power Limiter, 0.01 to 18 GHz
N9355B
-
The N9355B power limiter provides the best broadband input power protection to sensitive RF and microwave instruments and components, like network analyzers, spectrum analyzers, and amplifiers, from excess RF power, DC transients and ESD. Minimize your measurement uncertainty and improve your measurement accuracy with the limiter's superior RF performance.
