-
Product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (f)
CK058F
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
16 / 180 MS/s Bit Waveform Digitizer
WFD16
Waveform Digitizer
The WFD16 is a 16 bit Waveform Digitizer for high-speed / high resolution waveform capturing and analyzing. The fully differential signal path ensures an exceptional high signal quality. Despite this emphasis on signal quality the WFD16 also has a good DC accuracy. The module features differential inputs with a 50 Ohm or 10 kOhm termination and a with a programmable common-mode voltage.
-
Product
Signal Injectors
-
Ideal high performance, low noise compliment to your Circuit Sleuth Frequency Response Analyzer. An injection transformer is used to couple an excitation signal from a frequency source into the feedback loop of a control system. This allows loop gain and phase vs. frequency to be measured, with the loop closed, thus characterizing the stability of the system.
-
Product
ISA Bus Dual Redundant MIL-STD-1553 A/B Simulator / Analyzer / Tester
CIC101-4
-
Price: Request QuoteMIL-STD-1553 A, B Simulator/Analyzer/Tester ISA BUS Interface Card. The CIC101 can be used for Validation Testing,Production Testing, full bus simulation and monitoring, as ageneral purpose 1553 interface or a stand alone bus Analyzer. It provides precise message scheduling andmeasurements. Major and minor frame times areindependent of message sequences or retransmissions onerrors. The start of all command messages may be set to beindependent of message length, response time or length ofresponse. The CIC101 features a calibrated Message timingand low jitter RT responses.
-
Product
Spectrum Analyzers
-
Frequency range:0.15∼500MHz(SA5005/SA5006T) 0.15~1050MHz(SA5010/SA5011T).Amplitude range:-100~+13dBm.Tracking generator(SA5006/SA5011T).Output level range:-50~+1dBm(in 10dB steps and var.)
-
Product
FieldFox Handheld Microwave Analyzer, 14 GHz
N9916A
-
14 GHz max frequency Carry the world's most integrated handheld analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in the same sweep Simultaneously measure all four S-parameters Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Calibrate simply with QuickCal
-
Product
4-in-1 OSLT Calibration Kit, DC to 26.5 GHz, Type-3.5 mm (m) 50 Ohm
CK520A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
Electromagnetic Compatibility (EMC) Testing Capabilities
-
Electromagnetic Compatibility testing analyzes the ability of electronic devices to operate as anticipated when in proximity to other electronic devices or in the presence of electromagnetic disturbances that interfere with their intended operation.We help you ensure EMC compliance and attain the needed EMC certifications by assisting you in maximizing accuracy, reducing testing cycles, and getting your products to market faster — from design conception to end-product completion even against the most demanding electromagnetic regulations.We understand that time to market is everything which is why our global testing capabilities and custom testing solutions utilize the latest technology and automation software, helping you meet demanding time-to-market needs. Our streamlined testing process brings your product from development to end use efficiently in accordance with government, regulatory, military, or industry standards based on your compliance needs.
-
Product
CGH + SNP Microarrays
-
Learn about our extensive range of CGH + SNP microarrays dedicated to cytogenetic workflows. We provide whole genome CMA at variable resolutions, down to exon level, CGH+SNP arrays to analyze CN and LOH in a single experiment and application specific designs, including pre- post-natal, PGS, CNV and Cancer specific microarrays. Agilent’s CGH platform provides unmatched flexibility on content and throughput, thanks to eight different microarray formats with variable density and arrays per slide. Agilent provides a database of more than 28 million validated probes, and easy tools to customize array content based on needs. Custom or catalog, all Agilent’s CGH & CGH+SNP arrays benefit from proprietary SurePrint technology with long, high quality oligos.
-
Product
Psychrometers
-
The In-Duct Hot-Wire Anemometer & Psychrometer accessory head, AAT3 allows HVACR professionals to measure air velocity, temperature, and %RH all in one tool. The engineered 38" telescoping probe with laser etching and quick-response sensor provides quick and easy airflow measurements from the correct location--near the evaporator. When using with the Fieldpiece HVAC Guide System Analyzers, the AAT3 can automatically calculate target super heat and target evaporator exit temperature.
-
Product
PCAP Analyzer
-
PCAP Inspector allows for quick and seamless segmented steps to prepare a focused and comprehensive analysis within Wireshark. During your visual and statistical analysis, select, and export the desired segments of your PCAP data, immediately importing your data into Wireshark.
-
Product
Sulfur Benchtop
-
XOS offers a variety of sulfur analyzers suitable for a wide range of analysis, throughput requirements, and operating environments. Imagine a smarter analysis solution free of compromise: hassle-free sample prep, easy operation, rapid testing, compliance flexibility, and industry-leading precision. These analyzers range from monochromatic wavelength dispersive XRF (MWDXRF) to high definition XRF (HDXRF) systems, delivering direct measurement without the need for consumable gasses or sample conversion.
-
Product
N2O/H2O Trace Gas Analyzer
LI-7820
-
The LI-7820 N2O/H2O Trace Gas Analyzer offers high-precision nitrous oxide measurements in a low power, portable design—enabling it to easily integrate into survey and long-term soil flux systems. Pair it with the LI-7810 CH4/CO2/H2O Trace Gas Analyzer or LI-870 CO2/H2O Analyzer for CO2 and CH4 measurements at your site.
-
Product
Zero Emission Cabinets
-
A zero emission cabinet is connected to the exhaust extration system of the building and prevents exhaust gases from escaping into the building.VLT offers several different zero-emission cabinets for use with emission and diesel smoke analysers. They can be connected to your exhaust extraction system. Mandatory in some countries.
-
Product
Basic Pulsed-RF Measurements Lite For P50xxB Up To 20 GHz
S970240B
-
Add pulsed-RF measurement capabilities to your P50xxB Streamline series vector network analyzer
-
Product
CellTest Multichannel Potentiostat
-
Simultaneous Electrochemical Impedance Spectroscopy (EIS) tests can be run on multiple cells by connecting Solartron 1455A/1451A series frequency response analyzer (FRA) modules to the 1470E. These FRAs can operate in single sine correlation or multi-sine / Fast Fourier Transform (FFT) analysis mode, providing the ultimate in speed, precision and accuracy. The 1455A FRA provides high performance impedance measurements over the frequency range 10 μHz to 1 MHz, while the 1451A FRA operates from 10 μHz to 100 kHz.
-
Product
Data Acquisition & Analysis
-
Avionics Interface Technologies
We provide fully integrated avionics data bus and high speed network analyzer and data acquisition systems. Combining our extensive product catalog of Avionics interface modules, and our easy to use Analyzer software applications, with our Engineering Expertise, we are able to satisfy a wide range of avionics network data capture and analysis requirements with our COTS products or with customized solutions.
-
Product
Portable Dew point Analyzer
GEN-25
-
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
GEN-25 dew point analyzer is a kind high-performance intelligent moisture tester, which is developed by film capacitive ceramic dew point sensor combine with latest micro computer technology. It is used to measure the moisture content in various gases.
-
Product
PXIe-5841, 6 GHz, 1 GHz Bandwidth, RF PXI Vector Signal Transceiver
786982-01
Vector Signal Transceiver
6 GHz, 1 GHz Bandwidth, RF PXI Vector Signal Transceiver - The PXIe-5841 is a vector signal transceiver (VST) with 1 GHz of instantaneous bandwidth. It combines vector signal generator, vector signal analyzer and high-speed serial interface capabilities with FPGA-based real-time signal processing and control. The PXIe-5841 features the flexibility of a software defined radio architecture with RF instrument class performance. This VST delivers the fast measurement speed and small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments. The PXIe-5841 is available with an optional high-performance local oscillator module for improved phase noise, measurement time, and EVM performance. You can use the VST to test a variety of cellular and wireless standards such as Wi-Fi 6 and 5G NR. In addition, you can expand the small, two slot 2U PXI Express form factor to support multiple input, multiple output (MIMO) configurations.
-
Product
PXIe Vector Signal Analyzer: 6 GHz
M9391A
Vector Signal Generator
RF requirements keep growing while timelines keep shrinking. To help ease the technical and business pressures, the right test solution provides continuity in measurements and longevity in capability. In the evolution of modular RF test solutions, the Keysight PXI VSA is the next logical step in signal analysis. With raw hardware speed and X-Series measurement applications, it delivers proven results faster. From fully modular hardware to software leverage to worldwide support, the PXI VSA is the low-risk way to manage change and be ready for tomorrow today
-
Product
NEXYGEN DF Force Measuring Software
-
The NEXYGEN DF software is an easy-to-use Windows based data analysis package for use with the digital force gauges and torque gauges. Your test results are presented in a spreadsheet format so you can analyse data and perform common mathematical and statistical calculations.
-
Product
Carbon / Hydrogen / Sulfur Analyzer
CHS‑580A
-
ELTRA’s 580A analyzers (A = Autoloader) are equipped with an automatic sample loader, allowing for analysis of large numbers of samples without operator intervention. The sample loader is available in two versions to accommodate 36 or 130 crucibles. The CHS-580A is based on the technology of the CHS-580 analyzer and features a vertical resistance furnace with ceramic tube.
-
Product
Firmware for High-speed HDLC Mode
OP-FW10
-
OP-FW10 is firmware to upgrade protocol analyzer LE-7200/LE-3200 to dedicated analyzer that is specialized for High-speed HDLC communication up to 10Mbps. By installing this OP-FW10 to LE-7200/LE-3200, HDLC measurement processing such as the trigger and filter that were processed by software of the analyzer can be replaced to the hardware processing by FPGA built in the analyzer. Therefore, a maximum speed of HDLC supported is vastly improved. After installation of OP-FW10, You can switch to the usual firmware that supports multi protocol by pressing “SHIFT” and “0” keys at the same time when turning on the power of the analyzer. Therefore, it saves you trouble to reinstall firmware.
-
Product
Functional Analyzers
-
Functional analyzers characterize the key properties of flour and grains to help manufacturers produce consistently high-quality baked goods and snack foods. Widely used in the wheat breeding, milling, and baking industries, our unique analyzers measure starch damage, sprout damage, solvent retention capacity, and impurities in flour and grain, providing multiple indicators for quality control.
-
Product
Shock Response Spectrum (SRS) Analysis Solution
-
Shock Response Spectrum (SRS) Analysis SolutionMechanical shock pulses are often analyzed in terms of the shock response spectrum. The shock response spectrum assumes that the shock pulse is applied as a base input to an array of independent single-degree-of-freedom systems. SDOF system assumes that each system hat its own natural frequency.
-
Product
DC - 400 MHz PC-Based Timer Interval Analyzer
-
GuideTech’s GT658PCI is an ultra-fast, high resolution, DC – 400 MHz Time Interval Analyzer (TIA), ideal for most PC-based lab bench (timing) test applications. What makes the GT 658 superior to traditional counters is analogous to the difference between volt meters & digital scopes. While both measure voltage, the scope provides much more information about the dynamics of the signal. This is because our patented TIA substantially increases measurement speed, and the measurements are displayed as afunction of time. All of these features, along with the benefit of ‘continuous time correlation to a common reference between all measurement time stamps,’ enable our TIAs to make measurements that weren’t previously possible with traditional counters.
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781775-01
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
Video Quality Monitoring Solutions
StreamScope
-
Award-winning StreamScope® ATSC 1.0 and ATSC 3.0 stream analyzers and monitors assure service quality and regulatory compliance for DTV networks.
-
Product
20 Bit / 2 MS/s Waveform Digitizer
WFD20
Waveform Digitizer
The WFD20 is a 20 bit Waveform Digitizer for medium-speed / high resolution waveform capturing and analyzing. The module combines an excellent dynamic performance with a very high DC accuracy. The module features a fully differential input path to reduce common-mode level disturbances.
-
Product
Atlas DCA Pro Advanced Semiconductor Analyser
DCA75
-
The DCA75 is a great instrument for identifying and testing a wide variety of semiconductor components. Just connect any way round! The DCA75 will perform the following:*Display component type (such as N-CH MOSFET, darlington transistor etc).*Display component pinout (such as drain, source, gate etc).*Display detailed parameter measurement.*Plot characteristics curves on your PC.
