Tensile
the ability of a material to be stretched.
See Also: Elasticity, Pull Testers, Extensometers, Tension
-
product
Tensile Tester
Wewon Environmental Chambers Co, Ltd.
Is a fundamental materials science test in which a sample is subjected to a controlled tension until failure
-
product
Tensile Test Chamber
CSZ's Tensile Test Chamber is an environmental chamber that interfaces with a customer tensile tester load frame. This chamber is required to expose various materials and components to temperature conditions while undergoing tensile test. Tensile testing stresses materials by pushing, pulling, twisting, or bending intended for static and fatigue testing.
-
-
product
Portable Tensile Tester
SG-L08C
Digital Compress and Tensile testing machine.It's appropriate to testing the resistant properties of all sorts of materials such as tensile force, compression, tearing force, peel force, adhesive force, etc.
-
product
Extensometers for Indirect Tensile Testing of Asphalt
Model 3911
Jinan Testing Equipment IE Corporation
For indirect tensile testing, such as for resilient modulus, these extensometers measure the lateral deformation of specimens. They are self-supporting on the sample and clip on in seconds. The traditional way this deformation has been measured was prone to errors caused by slight rocking of the sample as it is loaded. The self-supporting design of the Model 3911 eliminates this problem. This unit will handle the dynamic pulse requirements of resilient modulus testing.The speed of mounting makes test set-up much faster than with the older method. The pivot mounting used ensures that the specimen contact pads meet the often uneven asphalt surface as well as possible. The measuring range options available allow a wide range of testing, yet can easily measure the sometimes very small displacements required.The Model 3911 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Tensile Strength Tester
Capacity of Tester with accuracy of 100g : 250 Kgf. and 500 Kgf.Capacity of Tester with accuracy of 10g : 20 Kgf, 50 Kgf and 100 KgfS Type Load Cell fixed with Top GripTraverse Speed: 300 & 100mm /min.Grip Separation: 1000 mmGrip Separation: 25 mmTop Grip is fixed and Bottom Grip is Movable Type.Elongation measurement by Steel Scale and Digital Counter Meter Both.Digital Display of Load and Elongation.Peak value of last test can be read.User friendly key panel with switch of zero setting and peak value of last testMotor: 1/2 HP single phase 220V 50 Hz. ( for Capacity up to 100 Kgf )Motor: 1 HP single phase 220 V 50 Hz ( for Capacity up to 500 Kgf)Power: 220 V AC 50 Hz.Safety device by limit switch to protect from over traverse.
-
product
Universal Tensile Testing Machines
Dongguan Amade Instruments Technology Co., Ltd
Universal tensile testing machines are testing equipment that are used to conduct mechanical testings of static load, tensile, compression, bending, shearing, tearing, stripping, applied to plastic sheets, pipes, tapes, rubbers, electric wires, springs, sponges, fibers etc. Tensile test is performed to measure and analyze the physical performances of different types of materials and finial products, playing an important role in developing new materials and controlling products quality. From the perspective of function, universal tensile testing(UTM) machine is an omnipotent instrument Just as the name implies. Clamps or fixtures are interchangeable on the basis of different test pieces, enabling various testings to be carried out on one tensile testing instrument. Options of single-column stand or twin-column stand can be available based on the specimen’s tensile/compressive force and dimension. Computerized tensile tester is preferred rather than microprocessor version If users want testing results including curve graphics between time, force and displacement.
-
product
Testing Tensile Strength of Overlays, and Overlayments
James Bond Test ™ MK III
The James Pull Off Adhesion/Bond Tester measures the pull force used to pull a 2? or 3? disc away from the material being tested. This pressure is displayed on a precision gauge and can be related directly to the strength of the adhesion to the surface being tested.
-
product
Textile Tensile Testing Machine
TF002
TESTEX Testing Equipment Systems Ltd.
Textile Tensile Testing Machine, to determine the physical and mechanical performance of tension, tearing, compression, bursting, rapture, flexibility, shear and peel and seam slippage. Especially designed to test a wide range of yarn, fabric, leather, with a huge assortment of specimen grips and software available, it can also be used for strength test of rubber, plastic, metal, wire, paper, packaging, and other materials
-
product
Subsea Data Logging Tensile Link
SUBD-3.0
The Subsea Data logging Tensile Link is a robust Tensile Link used for measuring loads on subsea mooring lines, underwater deployments and other similar applications. The instrument measures and records the applied load using an internal data logger which was developed by DLM Design Engineers.
-
product
Standard Tensile Link
SL-3.0
The SL-3.0 is a cable connected Tensile Link available with capacities ranging from 1t to 500t. These devices can be used in various tension load monitoring applications for industries worldwide and combine high levels of performance with excellent value.
-
product
Electronic Tensile Strength Tester Pull Force Test Chamber Applicable Industri
Shenzhen Chuangxin Instruments Co., Ltd.
This machine can test various materials (both finished and semi-finished products ) of tensile strength ,compressive strength and elongation ,can do stripping ,tear strength ,flexural ,compression test and etc. It can connect up to the computer and display or printout the test times , test value , max. value , etc . Also it can make various report forms according to the requirements .
-
product
Automatic tensile testing machine
This device evaluates the tensile characteristics of plastics and plastic composite materials. The sample is automatically measured for its size and tested when set in the feed section. Very high-precision elasticity measurement is possible.
-
-
product
Tensile Sample Preparation
Jinan Scientific Test Technology Co. LTD.
Tensile Sample Preparation
-
product
Intelligent Tensile Testing Machine
XLW-H
XLW-H Intelligent Tensile Testing Machine specializes in testing the mechanical properties of various flexible packaging materials. It is mainly used to test the heat seal strength, tensile strength, peel force, elongation of pharmaceutical packaging materials, aluminum foil, PVC hard sheet, composite film, syringe and other products.
-
-
product
Tensile Testing System With Thermostatic Chamber
This thermostatic chamber is ideal for long-stroke tensile testing of large-elongation materials such as rubber and plastic in controlled temperature environments.
-
product
Fully Automatic Rubber Tensile Testing System
Compactly Integrating Functions Required for Quality Control of Rubber Shimadzu Fully-Automatic Tensile Testing System This system provides full automation, from measurement of specimen dimensions, supply to the testing machine, and fixing of chucks to measurement of extension between standard lines and data processing. The system can be used for continuous nighttime testing, which helps save labor costs.
-
product
Textile Tensile Testing Machine
TF001
TESTEX Testing Equipment Systems Ltd.
The Textile Tensile Testing Machine is designed to test a wide range of materials in tension, bursting, tear, elongation, constant load, elastic, thread slip, peeling and other mechanical properties.A PC-controlled machine equipped with AC servomotor and a quality ABBA ball-screw for ideal and smooth control. The machine talks directly with a PC running a data analysis software package in English or Chinese, via a high speed RS232.
-
product
2-500kg Computer Servo Tensile Test Instrument
JY－106B
Shenzhen Chuangxin Instruments Co., Ltd.
The Computer Servo Tensile Testing Machine is widely to test the tensile, tear, peel and bend of all kinds of
-
product
Gamlen Tablet Tensile Analyzer
TTA
Automatic measurement of key tablet critical quality attributes
-
product
Digital Electronic Tensile Test Machine
Shenzhen Chuangxin Instruments Co., Ltd.
The Tensile Testing Machine is widely applied to test the tensile, tear, peel, and bend of all kinds of materials, such as metal, cable and etc, it’s used to test the tensile, tear, peel, compressive strength and bending of the material. It conforms to the standard of GB, ISO7500/1, JJG475-88, ASTME4, DIN5122, JISB7721/B7733, EN1002-2, BS1610, and CNS9471/9470.
-
product
Long-Stroke Tensile Testing System For Vulcanized Rubber
Capable of Measuring Even Specimens with a Large Break Strain A tensile test method for vulcanized rubber is stipulated in JIS K6251 (Rubber,vulcanized or thermoplastic-Determination of tensile stress-strain properties). One of the properties of vulcanized rubber is significant elongation. This long-stroke tensile testing system for vulcanized rubber has a long stroke that is required for calculating these tensile characteristics of rubber, and accommodates dumbbell specimens Nos.1 through 6 stipulated in JIS K6251.
-
product
Telemetry Tensile Link
TL-3.0
The TL-3.0 is a third generation Telemetry Tensile Link load cell. A light weight wireless tension measuring unit that combines a high level of performance with a robust design for harsh environments.
-
product
Pneumatic Side Action Tensile Grips
2712-04x Series
Instron’s pneumatic side-action grips provide a high-performance, repeatable, and safe gripping solution for a broad spectrum of materials — from fine wires, fibers, textiles and foils to plastics, elastomers and components — via air-actuated clamping that maintains constant force even as specimens deform. With quick, tool-free jaw face changes, optional alignment and centering devices, adjustable opening and flow control, and integrated safety features (e.g. jaw face shields), these grips are engineered for throughput and reproducibility operator protection in tensile testing applications.
-
product
Biaxial Tensile Texting Machine of Membrrane Structure
BTT Series
Jinan Testing Equipment IE Corporation
The biaxial tensile testing machine consists of two parts, mechanical system and control system; mechanical system includes load frame, membrane specimen fixtures, servo motors(Japan), load sensors, displacement sensor and other components, while control system with the computer and software;
-
product
Universal Testing Systems (Up To 300 KN)
6800 Series
Instron’s 6800 Series universal testing systems deliver high-performance mechanical testing up to 300 kN. Designed for precision and durability, these systems offer exceptional measurement accuracy (±0.5% down to 1/1000th of load cell capacity) and fast data acquisition rates up to 5 kHz. Ideal for tensile, compression, flexure, torsion, peel, lap shear, and many other test types, the 6800 Series provides the flexibility and control needed to handle everything from delicate specimens to high-strength materials, making it a trusted solution for demanding testing environments.
-
product
100 N Pantograph Grips
Pantograph grips use a simple spring design to hold and apply pressure to specimens during tensile testing. These grips are mainly used for tensile testing plate specimens of rubber, textiles, or soft plastics.
-
product
Single column automated force test stand up to 500 pounds
701SN
The advanced 701 Universal Test System is ball screw driven test stands, excellent for affordable, precision tensile and compression testing of a wide variety of materials or products up to 500 pounds.This variable speed tester has increased speed ranges and include adjustable travel limit switches. With the unique dual testing area, users can setup for two tests, tensile and/or compression, without having to switch out fixtures.
