Fault
-
Product
PXI BRIC8 FIBO Matrix Dual 30x2 3pin brkout
40-595A-005
Matrix Switch Module
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
Product
Downed Conductor Detection
-
Schweitzer Engineering Laboratories, Inc.
Downed conductor detection technologies detect many high-impedance faults on a distribution system, improving safety as well as mitigating wildfire risk.
-
Product
OTDRs
-
An Optical Time Domain Reflectometer (OTDR) tests the integrity of a fiber optic cable. Using a fiber OTDR, a technician can verify splice loss, identify length, and very easily locate faults in the cable. Another use is to verify the accurate installation of a fiber optic cable when it’s newly installed. If/when problems arise or if an issue is suspected in the future, a fiber OTDR can then compare the images from the original trace to the present state of the cable.
-
Product
SIM Filter
-
The CFL SIMF, Cable Fault Secondary Impulse Filter from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately.
-
Product
PXI BRIC4 FIBO Matrix Dual 124x4 2pin Brkout
40-592A-014
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines. Typical applications are in automotive and aerospace industries which involve safety or mission critical systems that have to behave predictably when cabling or sensor faults occur.
-
Product
Cable Test Box
-
Cables are a critical part of any sensor measurement system and damaged cables cause frequent delays during test setup. PCB has developed a relatively simple device to test cables on a channel by channel basis for BNC, 10-32, and 5-44 coaxial connectors. Simply connect both ends of the cable and faults will be indicated for shield failure, conductor failure, or short circuit shield to conductor. Power is provided by a single, replaceable 9 volt battery.
-
Product
32 Channel Multi-Purpose DIOS/TAP Modules/Interfaces for Spare JT 2148 QuadPOD Transceiver Slot
JT 2149/MPV eMPV
Interface
The JT 2149/MPV and the JT 2149/eMPV are a 32 channel multi purpose DIOS/TAP pod modules/interfaces that can be plugged into any spare JT 2148 QuadPOD transceiver slot. The DIOS channels of these units I/O interface pods enable increased fault coverage and thus improved diagnostic resolution during boundary-scan testing. The principal difference between the two versions is the use of an extended case on the eMPV that allows standard 0.1″ connections to be used to access ths TAP and static IO signals (see tab below)- on the standard /MPV unit these signals are available at the front face 0.05″ connector. The units are fully supported by JTAG Technologies’ development tools. Additional DIOS modules can be serially connected if more parallel access points are required.
-
Product
Advanced Diagnostics for ScanExpress™ JET JTAG Embedded Test Solutions
ScanExpress JET Advanced Solutions
-
ScanExpress JET advanced diagnostics add additional diagnostic resolution with fully automated analysis translating functional test results to down to the net and pin level, even with BGA packages.The seamless integration with ScanExpress JET and ScanExpress Runner as well as the ability to output ScanExpress Viewer fault reports for PCB visualization make ScanExpress JET Advanced Diagnostics a must-have tool for any JTAG test system.
-
Product
Cable Fault Locator
-
We are one of the leading manufacturers, exporters of suppliers of a premium quality range of Cable Fault Locator that is extensively used to trace and locate the fault of underground cables. This fault locator is manufactured at our hi-tech manufacturing unit as per international quality standards under the supervision of our professionals using superior quality components. Offered fault locator is made available in different specifications to meet the diverse requirements of the clients. Our honorable clients can avail this Cable Fault Locator from us at industry-leading prices.
-
Product
Earth Resistance
-
Precision Mastech Enterprises Co.
Specialized instruments designed to measure the effectiveness of earthing systems, ensuring electrical fault currents safely dissipate into the ground to protect people and equipment.
-
Product
Cable TV
-
Tempo Communications provides technicians with an array of test and measurement solutions to optimiz... e the installation and performance of broadband cable networks. The tried-and-true TDR from Tempo delivers all of the enhanced features required to pinpoint faults and verify performance. Like all of its test and measurement devices, the focus is on reliability, ease-of-use, and quality—empowering technicians to do their jobs and exceed customer expectations.Show less
-
Product
VLF test system
BAUR PHG 80 portable
-
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
-
Product
Ground-Fault Location Products for Ungrounded Systems
-
When combined with Bender's ground-fault detectors and current transformers, EDS series modules provide fast, automatic ground-fault location in ungrounded systems. Fault location takes place while the system remains online without the need to open branch circuit breakers or disconnect equipment. Bender's fault location system works on both AC and DC systems, as well as systems with variable frequency drives. A standalone, portable fault location system is also available.
-
Product
PXI BRIC8 FIBO Matrix Dual 6x4 3pin brkout
40-595A-006
Matrix Switch Module
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
Product
Cable + Network Tester
LinkIQ
-
The LinkIQ™ Network+Cable Tester is designed to provide trusted cable testing along with network testing professionals need to do their jobs. LinkIQ™ validates cable performance (up to 10 Gig) using frequency-based measurements and provides distance to fault information along with a wire map of the cable under test.
-
Product
PXIe-5110, 100 MHz, 1 GS/s, 8-Bit PXI Oscilloscope
785767-01
Oscilloscope
PXIe, 100 MHz, 1 GS/s, 8-Bit PXI Oscilloscope—The PXIe-5110 oscilloscope has two channels that sample up to 1 GS/s with flexible and programmable settings for coupling, input impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that facilitates high-speed data throughput and includes analysis functions. This device is ideal for automated and partially automated applications that require flexible measurement configurations and up to 100 MHz of analog bandwidth. The PXIe-5110 also features advanced PXI synchronization and data throughput capabilities. Some options also support CableSense™ technology, which can detect and locate signal path faults, changes, or discontinuities.
-
Product
Pin Pointer
CFL PP3+
-
The new generation CFL PP3+ Cable Fault Pin Pointer cum route tracer from SCOPE is the ultimate solution for locating of underground cable faults in minimum time by tracing cable route. It uses an advanced technology which helps even an unskilled operator to locate the fault accurately.
-
Product
Fiber Optic Visual Fault Finder
VFF5
-
Used to verify continuity, test and find breaks in fibre links, locate pinched fibre strands in termination cabinets, or anywhere fibre optic cables are terminated and subject to mechanical damage.
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-193A-002
Switch Module
The 40-193A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
Product
Optical Fiber Ranger
TM190
-
Optical Fiber Ranger TM190 is portable fiber fault locator, it is quickly to detect fault location and type of optical fiber using OTDR element and stronger soft ware analysis tool.
-
Product
PCI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Output, Bank-Isolated Digital I/O Device
778836-01
Digital I/O
The PCI-6514 is an industrial digital I/O interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in … software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Turns Ratio Testing
-
The transformer turns ratio test, or TTR test, confirms that the transformer has the correct ratio of primary turns to secondary turns. Using this test correctly can help to identify tap changer performance, shorted turns, open windings, incorrect winding connections and other faults inside transformers. Megger’s range of TTR testers are robust to withstand the harsh conditions that some transformer testing in. The range includes varying features to simplify and speed up testing as well as 3 phase TTR testers and PT and CT TTR testers.
-
Product
LASAR Post Processor, Run Time And Diagnostic Test Solution
DtifEasy Series
-
DtifEasy is a full-featured tool set for importing, converting, and executing IEEE-1445 compliant digital test vectors generated by a LASAR simulation. All four IEEE-1445 file types - UUT model group, Stimulus and Response group, Fault Dictionary group, and Probe group are supported by DtifEasy; providing the user with the ability to execute go/no-go, fault dictionary, and guided probe sequences. DtifEasy supports MTS' 3U PXI GX529x series of dynamic digital instrumentation to 200 MHZ as well as the 6U PXI GX5960, 50 MHz digital instrumentation. All of these instrument families are compatible with the digital logic probe.
-
Product
OTDR
-
OTDR, short for optical time-domain reflectometer, is an optoelectronic instrument used to characterize an optical fiber. It can offer you an overview of the whole system you test and can be used for estimating the fiber length and overall attenuation, including splice and mated-connector losses. It can also be used to locate faults, such as breaks, and to measure optical return loss.
-
Product
Cable Testers
-
The CableTool uses TDR (Time Domain Reflectometry) technology to quickly identify an open or a short from 0 to 2,500 feet within a foot of the fault.
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
Fault Insertion Unit
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
High Voltage EMC Surge Generator
TM510
-
TM510 Surge Generator is mainly used for testing power cable high-resistance and arc-over fault whose grade range is 0-10kV, co-operating with cable fault tester and locating devices to test and locate faults. If the user choose the professional digital milli-ampere-meter, as for cable with grade range about 0- 6kV, the instrument can also be used to do DC&voltage resistance test and current leakage test after the fault is repaired. The instrument is internally equipped with voltage-rise rectifying and discharging device, has complete functions, and is also convenient and safe to be wired and operated.
-
Product
Communications Test System for Frontline Diagnostics
CTS-2750
Test System
The CTS-2750 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
Product
Combined Map Display Unit & Interface Unit Tester (COMED)
MS 1117
-
This system is used to test COMED (Combined Map Electronic Display) IFU cards. This ATE checks the LRU Status and card status and identify faulty component in the individual UUT. On fault, this suggests the possible component failure as diagnostic report, for repairing the cards.
-
Product
Cable Fault Locating Equipment
-
Commonly used to test underground coaxial and twisted pair cabling, along with transmission lines and other industrial electrical cables.
