Fault
-
product
PXI Dual Bus 74-Chan 2A Fault Insertion Switch, N/O Through Relays
40-190B-302
The Dual Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
PXI Fault Insertion Matrix Modules
All of our fault insertion matrices feature a breakout arrangement that allows faults to be attached to the sensor lines via the Y axis. This includes the breaking of a connection or the adding of a series defect – all of which can simulate connectivity problems in the system. The three pin breakout versions allow the connection to be swapped for a “bad” sensor simulation.
-
product
Burn Down Transformer
ATG 2
Cable fault location with the BAUR ATG 2. The ATG 2 burn down transformer is used for impedance reduction of cable faults in low- and medium-voltage networks. The short-circuit proof 2300 VA stray field transformer delivers a maximum voltage of 10 kV and is housed in a fully enclosed 19" housing.* Portable device for changing the fault resistance* Useful for cables that are difficult to access* Proven methods for complicated faults* Independent current and voltage control on each burning level
-
product
Smart Electric Tester
SET-12
The SET-12 Tester is a portable device for measuring electrical parameters. Unique combination of the most needed measurements into one device allows for a quick diagnosis of faults.
-
product
RCD Testers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2710 is a residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE). RCD testers let a fault current flow and thus determine at which fault current the RCD triggers. The tripping time is also measured. These two parameters, tripping current and tripping time, are the safety-relevant parameters of an RCD. The various selectable test currents and characteristics that can be set with this device make the PeakTech 2710 the ideal companion for every electrician.
-
product
Cable + Network Tester
LinkIQ
The LinkIQ™ Network+Cable Tester is designed to provide trusted cable testing along with network testing professionals need to do their jobs. LinkIQ™ validates cable performance (up to 10 Gig) using frequency-based measurements and provides distance to fault information along with a wire map of the cable under test.
-
product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-45NK
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement*DC leakage current measurement*Least affection from the magnetization of core and temperature fluctuation*Convenient ＋24V single polarity power supply
-
product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-193A-002
The 40-193A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
product
PXI BRIC8 HD FIBO Matrix 186x8 2pin brkout
40-592-121-186X8-2P
The 40-592 FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC™ format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short-circuits to ground or battery, or short-circuits between input/output lines.
-
product
PXI BRIC4 FIBO Matrix Dual 80x4 3pin brkout
40-592A-004
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Transformer Protection
Schweitzer Engineering Laboratories, Inc.
Transformer protection products and systems provide complete primary and backup protection for all types of transformer faults. They are suited for use in utility-, industrial-, and commercial-scale power transformer systems.
-
product
PXI BRIC4 FIBO Matrix Dual 40x4 3pin brkout
40-592A-002
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
250 and 260 Series pH Handheld Meter Kits
Get easy-to-read and accurate readings with auto-hold, auto-stable, and real-time measurements with stability indicators. The Environmental Express® Oakton® 200 series of water quality meters features an electrode status indicator, which shows the condition of the electrode after each calibration. Easily view electrode condition, reading stability, measured parameter, and temperature in one screen. Don’t worry about accuracy in fluctuating temperature—ATC ensures measurement accuracy. The simple user interface features adjustable auto shut-off time ranging from 1 to 30 minutes. Self-diagnosing meters display measurement and meter issues for fast fault finding and troubleshooting. Easily take measurements and conveniently store meter and electrodes with built-in foldable stand on the back of the meter. Two grooves on the side of the meter serve as electrode holders, to hold up to 2 electrodes. Choose from two series—the 250 series feature 500 data points (scroll thru on meter) while the 260 series features 1000 data points, a real-time clock, and USB communication for data down loads.
-
product
Pipeline & Cable Fault Locator
TM2000
TM2000 Pipeline & Cable Fault Locator is designed for the Underground utilities route locating, the depth measuring and disatance tracing.
-
product
Fault Locating
Schweitzer Engineering Laboratories, Inc.
The built-in fault-locating methods in SEL devices allow you to quickly identify faults, dispatch crews for repairs, and restore service faster. Traveling-wave fault-locating technology calculates the locations of temporary and permanent faults by measuring the arrival times of the naturally occurring traveling waves caused by a transmission line fault. Accurately detecting these waves requires ultra-high-resolution monitoring, and locating is accurate to within one tower span (±300 m). Impedance-based fault-locating technology calculates fault locations by detecting changes in line impedance as a result of a fault. Impedance-based locating is reliable and accurate to about 2 percent of a line’s total length.
-
product
Low Voltage Solutions
Our market-leading range includes real-time LV monitoring systems, portable fault-finding devices, and software tools, all designed to help you proactively manage your Low Voltage network and address any faults efficiently. Stay one step ahead with our powerful insights and innovative solutions.
-
product
Data Acquisition Module for Embedded Systems with IO60 expansion
IO60-M410
WINSYSTEMS’ IO60-M410 is a reliable data acquisition module for embedded systems with IO60 expansion featuring 24 GPIO (General Purpose Input-Output) tolerant to 30 V DC. Activity LEDs indicate device communication and DAC fault. WINSYSTEMS can provide custom configurations for OEM clients. Please contact a Applications Engineer through our contact page for details.
-
product
Dual Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-102
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Endpoint / Chamber Health Monitor based on Optical Emission Spectroscopy and MWL Interferometry
EV 2.0 Series
To address new requirements in Semiconductor, lighting devices, automotive components, flat panels, MEMS sensors, memory chips, and logic electronics processed in the industry using dry etch, cleaning and (PE)CVD, HORIBA has introduced a unique generation of sensor dedicated to Advanced Endpoint Control, Fault Detection and Chamber Health Monitoring.
-
product
Power Meter
OrienTek Optical Technology Ltd.
Power Meter and the Visual Fault Locator.The Optical Power Meter can measure dBm,dB and uW in the wavelength band of 850,1300 1310 1490 1550 and 1625nm.The Visual Fault Locator uses CW mode and Modulation mode and helps to detect the optical cable of up to 10km. Battery performance 50 hours operation,Dust and shock proof design,Auto Shut off function.
-
product
Pre- Locator
CFL PL2+
The new generation CFL PL2+ Cable Fault Prelocator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 50 km.
-
product
Fault Passage Indicator for Lines
LineTroll R400D
LineTroll R400D Fault Indicator indicates earth- and short-circuit faults and can distinguish between permanent and transient faults. The indicator has two sensors and use both the electrical field and the magnetical field to detect faults on all three phases.
-
product
Surge Generator
CFL SG 3210
SCOPE offers CFL SG 3210, Surge Generator with output of 32kV and 1000 Joules. It is ideal choice for fault location on all types of power cables from LV to EHV. CFL SG Series is equipped with different Protections, Interlocks and Auto-discharge Facility to ensure User Safety during operation. User Friendly controls, adequate form factor, contact free HV terminations makes this CFL SG Series most durable and best-designed sets in the segment.
-
product
GOOSE Message Recorder
TR-61850
Whether a new or existing installation, AMETEK’s TR61850 adds the capability to easily monitor and record GOOSE messages within the substation. All data from the fault recorders and TR61850 automatically merge providing a single point of reference when analyzing transient events and system disturbances. With a wide range of time synchronization, communication options and small form factor, the TR61850 seamlessly integrates into any application.Configuration of the GOOSE Message subscriptions is quick and easy with AMETEK’s configuration tool. Using the IEC61850 Substation Configuration Language (SCL), third party IED Capability Description (ICD) files are imported and subscriptions are created by simply dragging and dropping available GOOSE message outputs.
-
product
Multi-Function Recorder
Platinum 2.5K
For all types of power system events, the Platinum 2.5K Multi-Function Recorder provides all the information you need to capture the complete picture. This comprehensive fault recorder simultaneously performs transient, sequence of events and disturbance recordings, phasor measurements and power quality analysis. All of these functions are performed at the highest level so it will meet your needs of today and the future. In a deregulated environment, the Platinum 2.5K is the best tool to provide the necessary data to increase revenues and retain your customer.
-
product
JTAG Visualizer
JTAG Visualizer is an advanced graphical viewer and data management system for PCB schematics and layouts. Visualizer integrates seamlessly with the JTAG Technologies family of boundary-scan products, such as the ProVision application development platform, and accepts PCB data from a variety of CAD, CAM and EDA tools. In design Visualizer provides DfT (design for test) feedback to the user by enabling a graphical view of fault coverage on their design. In manufacture and test Visualizer can be used to highlight faulty nets (short circuits, opens, stuck-ats etc.) in both layout and schematics views.
-
product
Current Protection Relay
The main earth fault protection relays in distributions systems, power stations & large manufacturing / processing plants can fail to detect a high impedance break down to earth causing hazard to human life & potential damage to plant & equipment. In these & other situations demanding extra sensitive earth fault protection, using solid state techniques, can be applied to detect earth currents down to 0.5% of the CT nominal current.
-
product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
The 40-205-008 (PXI) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
Transient Stability Analysis
I*SIM
PTW I*SIM is a program for transient stability analysis. It is designed to simulate system response during and after transient disturbances such as faults, load changes, switching, motor starting, loss of utility, loss of generation, loss of excitation, and blocked governor events. I*SIM is designed to study today's most challenging simulation problems in one convenient and easy-to-use program.
-
product
Advanced Data Acquisition And Control System
ADACS
This high-speed damage-control system was built around Arc Fault Detect and Continuous Thermal Monitoring (AFD/CTM) from the Johns Hopkins Applied Physics Laboratory. When AFD/CTM detects dangerous arc faults — powerful discharges of electricity between conductors — the ADACS system immediately cuts power to the affected circuit before it can damage equipment or injure nearby personnel. Altogether, the system prevents loss of life, preserves countless repair dollars and assures continuous readiness.
