Parallel Interface
Connection between devices transmitting information through multiple conductors simultaneously.
See Also: Interfaces, Serial Interfaces, Bus Interfaces, UI, MIPI, Interface Adapters
-
Product
PCI Express System Timer (USB Interface)
SKU-032-01
-
The MiniPCI Express System Timer uses a standard USB interface to synchronize IP signals. This system timer provides accurate clock timing for Asterisk® open-source PBX software.
-
Product
30 GHz differential probe with ProAxial interface
DH30-PX
Differential Probe
30 GHz differential probe with ProAxial interface.
-
Product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
-
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
Test Fixture
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
CAN Sensoy/ Interface
Strain
-
Reach Technologies' CAN Strain Sensor Interface sources, conditions and digitizes 8 strain sensor inputs for collection via CAN. The module is ideal for conveniently adding strain data to a distributed CAN network. The CAN Strain Sensor Interface is configurable via a CANopen stack.
-
Product
GPIB To Ethernet Instrument Interface
-
*ICS's 4865B GPIB to Ethernet Instrument Interface adapts instruments with Ethernet interfaces to GPIB test systems.*ICS's 4865B provides a VXI-11 compliant interface for instruments that support the VXI-11 protocol and a smart, user-configurable, raw socket protocol that accommodates most instruments that use raw sockets. The 4865B replaces our earlier Model 4865 and is 2x to 5x faster than the original Model 4865. Click here for the original 4865 webpage.
-
Product
VXI Register-based Interface Board
-
VXI Register Interface mates with user's PCB to form a B or C-size module.
-
Product
PXI-8513, 1‑Port, Software-Selectable PXI CAN Interface Module
780688-01
CAN Interface
1‑Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
Network Interface Card
NIC10GBT
Interface Card
The NIC10GBT is a dual port 10GBase-T XMC module that brings 10GbE expandability to new and existing embedded systems with available XMC slots.
-
Product
Bench/System Precision Linear Regulated DC Power Supply With Digital Control, Single Or Triple Outputs, 105 To 242 Watts, With/without Remote Interfaces
QL Series II
-
Advanced dc power supplies, single or triple outputUp to 112 watts per outputVery high precision, very low noise, excellent dynamicsAdvanced user interface with numeric and rotary controlMultiple voltage/current ranges for increased flexibilityMultiple non-volatile memories for power supply set-upsSwitchable remote sense provides perfect load regulationComprehensive protection including OVP and OCP tripsCompact bench footprint; modular width for rack mountingAuxiliary output fully variable 1.00V to 6.00V at 3A with selectable voltage and current metering (T models)Bus programmable via USB, RS232, GPIB or LAN (P models)LAN interface is LXI compliantDuplicate power and sense terminals at rear (P models)
-
Product
15 Pin Breakout Interface
VSI-Breakout-15
-
The VSI-Breakout-15 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
Test Fixture
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Ethernet Module
M4K-ETH
Ethernet Interface
The M4K-ETH is an intelligent Gigabit Ethernet interface module for the multiprotocol Excalibur 4000 family of carrier boards. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Bench/System/ATE Programmable DC Power Supply Single Or Dual Outputs, 360 To 840 Watts, With Or Without Remote Interfaces
CPX Series
-
PowerFlex design gives variable voltage and current combinations within a maximum power rangeUp to 60 volts and up to 20 amps180 watts or 420 watts maximum per outputIsolated outputs can be wired in series or parallelConstant voltage or constant current operationSettings Locking (S-Lock)PowerFlex or fixed-range operationVariable OVP tripsSelectable remote sense terminalsCompact quarter or half rack 3U case sizeIsolated analogue remote control (CPX400SA only)RS232, USB & LXI compliant LAN (P models only)GPIB Option (P models only)
-
Product
Smart GPIB Serial Interface Board
Model 4806
-
* Provides GPIB-to-serial and serial-to-serial data paths for serial devices with RS-232 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message. • On board voltage regulator for operation from 5 to 15 Vdc power. • Rear panel mounting eliminates cables.
-
Product
Power Interface Board 6U, 1 PSU connector with AC pins
106PIBM601-9001R
-
The PIB 6U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
USB 3.0 and Ethernet to VME Interface
SIS3153
-
The SIS3153 is the successor to our SIS3150 USB2.0 to VME interface.
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 6 or 10 Positions Blocks, UUT 456 x 320 mm
MG-07-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 456 x 320 mm (wxd)• Outer dimensions: 620 x 589 x 100 x 184 mm (wxdxh1xh2)• Equipped with dedicated cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
Product
Quad Serial FPDP Interface with Virtex-6 FPGA - PCIe
Model 78611
-
Model 78611 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. A multichannel, gigabit serial interface, it is idealfor interfacing to Serial FPDP data converter boards or as a chassis-to-chassis data link. The 78611 is fully compatible with the VITA 17.1 Serial FPDP specification. Its built-in data transfer features make it a complete turnkey solution. For users who require application-specific functions, the 78611 serves as a flexible platform for developing and deploying custom FPGAprocessing IP
-
Product
ECU & Bus Interface Modules
ES500
-
ETAS makes the entire software and hardware range available from program development to the calibration of your ECUs. You can use the ETAS tools to address all ECUs that satisfy the ASAM standard. By using these standardized interfaces, our tools are not limited to the ECUs of any particular manufacturer.
-
-
Product
PXI-8368, MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module
783934-01
Remote Control Interface
MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module—The PXI‑8368 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8366 through a copper, x1 MXI‑Express cable. The fiber-optic cabling of the PXI‑8368 provides electrical isolation between the PC and PXI chassis, as well as cabling up to 200 m per link.
-
Product
GPIB Analog Interface
Model 4861B
-
ICS's GPIB to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Optional isolated Analog inputs. Available in rack mountable Miniboxes™ and OEM board versions. All of ICS's GPIB to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
Product
Serial to Parallel Analysis Package
B4601C
-
Your system uses serial buses to communicate between ICs and transfer data to and from peripheral devices. Sifting through thousands of serial bits by looking at long vertical columns of captured 1's and 0's can be very tedious, time-consuming, and error prone. The Keysight Technologies B4601C serial to parallel analysis package is general-purpose software that allows easy viewing and analysis of serial data.
-
Product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
37 Pin Breakout Interface
VSI-Breakout-37
-
The VSI-Breakout-37 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
RS-232 to RS-422/RS-485 Interface Converter
Model 9365
-
FEATURES: DIN Rail Mountable; User Selectable RS-422 or RS-485; User Selectable Two- or Four-wire RS-485; DataSpy® LCD Display; Intelligent Control of RS-485 Transmitter and Receiver; DTE/DCE Compatible; Data Rates Up to 115.2 kbp.
-
Product
3U CompactPCI Serial Power Interface Board
046-201
-
Standalone Power-BP 3U 8HP to connect CPCI Serial power supplies to compactPCI Serial-BPs. The connection is made via cables.
-
Product
Software and Interfacing
-
The installed sophisticated software offers many possibilities for signal storage, processing, visualization, etc. This includes the Fourier Transform analysis, and the line shape fitting of resonance. The system can also control external devices through the GPIB interface.
