Impulse Voltage
-
Product
Voltage Meter MDN8I-PXIe
MDN8I-PXIe
-
The MDN8I-PXIe module is made in the PXIe standard and is designed to measure instantaneous voltage values over eight isolated channels with differential inputs.
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
Transient Voltage Suppressors (TVS)
-
A transient voltage suppressor (TVS) is an avalanche diode specially designed to clamp overvoltages and dissipate high transient power surges. ST’s Transil™ protection devices are able to shunt a high current surge for a short duration.
-
Product
Dual Channel High Voltage Linear Amplifier
F10AD
-
his unit contains two independent F10A amplifiers that share common ground reference and power supply.
-
Product
Current / Voltage input Panel meter with output options
DM3420
-
The DM3420 panel meter accepts Voltage and Current process signals and displays the process value on a high efficiency daylight readable LED display. A built in transmitter power supply is also provided.
-
Product
Non-Contact Voltage Testers
-
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
Product
High Voltage Measurement
-
High Voltage Pulse Attenuator is used to attenuate high voltage pulse signals in a 50 system. It is consist of highly surge robust components with great voltage linearity. The device is symmetrical, Input and output can be exchanged.
-
Product
Fiberglass Telescoping Handle for the High Voltage Contact Tester
HV-43
-
Used for checking voltage up to 1,000V AC.Connects to the hot stick end of the High-Voltage Contact Tester (Cat. No. HVCT1).Dielectric pole type-tested & rated for 10kV AC.Comes in a convenient zippered pouch.
-
Product
Precision Voltage to Current Converter
64-VCC
-
The 64-VCC precisely converts voltage to current. The unit can be placed in-line with a data acquisition system to achieve outstanding conversion accuracy for precise movements in valves or motors. The unit includes a unique current feedback measurement output to precisely monitor actual current in critical applications.
-
Product
120-600V Solenoid Voltage&Continuity Tester
1867
-
Peaceful Thriving Enterprise Co Ltd
Test voltage from 120-600V AC/DC polarity and continuity.
-
Product
Bipolar Supply Voltage Output D/A Converters
-
Analog Devices is an industry-leading provider of bipolar d/a converter solutions offering exceptional 1 ppm performance and optimized feature sets to ensure quick and easy deployment of bipolar converters across a range of end applications. With a comprehensive portfolio of bipolar DACs fabricated using proprietary iCMOS® process technology, ADI has enabled the development of high performance ICs at high voltage levels while simultaneously reducing package size and power consumption. By bringing together the many benefits of integration, ADI’s bipolar DACs reduce design time and system complexity.
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-714-HI
Multiplexer Module
The 65-231-714-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 7 kV. Multiplexers are created by populating the 65-200-002 scalable chassis with multiplexer plug-in modules that provide access to the Channel and Common signals on 51-pin front panel connectors. Users can specify as many or as few plug-in modules as they require and can field upgrade the chassis to extend the multiplexer.
-
Product
PXI High Voltage Programmable Resistor Module, Connector
40-230-323-HI
Programmable Resistor Module
The 40-230-323-HI (PXI) and 42-230-323-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 3.55kΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-906-HI
Multiplexer Module
The 65-231-906-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
AC DC High Voltage Break Down Tester
-
RR – AC DC HIPOT TESTERS can perform such precise dielectric test in a cost effective manner without any compromise on safety. Our hipot testers are custom made to suit needs of various industries and product ranges. A Singe tester can be used for conducting both AC and DC Insulation Testing.
-
Product
PXI Voltage Amplifier SMB Type Connector
41-650-002
Amplifier
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
Product
Stand Alone Low Voltage Tester
Model 64×2
-
Internal Memory: 8 program locations without test point labels or 2 program locations with test point labels. Removable Memory: 16 program locations without test point labels, or 4 program locations with test point labels.
-
Product
High Voltage Surge Comparison Test Set-Up
-
Relying on our years of experience in this industry, we are highly acclaimed for manufacturing and exporting High Voltage Surge Comparison Test Set-Up. With wide use in electrical and power generation sector, this equipment is available in different technical specifications and models. We manufacture this High Voltage Surge Comparison Test Set-Up in accordance with industry standards using high grade raw materials. We offer this testing equipment to clients at competitive price.
-
Product
High Voltage Isolator for Logic Analyzers
LX-08
-
The LX-08 series of high voltage logic analyzer adapters provides a safe isolated method of measuring high voltage control signals with a low voltage logic analyzer. All inbound signals are optically isolated and attenuated to a safe level for the delicate inputs typically found on logic analyzers. The inputs on the LX-08 are capable of withstanding voltages up to +/- 300V AC/DC, higher voltage configurations are available upon request. Rather than probing with multiple neon screwdrivers, the LX-08 can provide simultaneous viewing of up to 8 circuits in the STANDALONE mode via the indicator array. Need to catch a transient event or map out a timing sequence? Just add a logic analyzer to the outputs of the LX-08 and turn it into a high voltage logic analyzer. High voltage signals that were hazardous for a logic analyzer can now be measured safely. Typical outputs of a high speed PLC sequencer can be precisely timed and measured from both sides of the control relay. With the built in user selectable AC filter circuit, an AC signal can be measured as DC events or AC cycles.
-
Product
Voltage Maintenance Program
VoltRef
-
VoltRef provides the power of automation formaintaining statistical control of the volt in yourlaboratory. This program controls a low thermalscanner and voltmeter to compare voltagestandards using the process recommended by NISTand other national laboratories.
-
Product
Non-Contact Voltage Detector
VOLTCHEK
-
The VOLTCHEK is a variable non-contact voltage detector, A proximity device which detects the presence of an alternating electric or electromagnetic field. It is used by industry professionals for live or dead voltage determination of outdoor overhead or underground at URD test points. Firstly as a proximity device to determine live or dead situations and then as a touch device to verify the source has physically reached the zero AC field. This is the only equipment capable of testing all voltage from AC 415V to 765kV from a distance, beyond arcing zone.
-
Product
AC High Voltage Break Down Tester
-
High Voltage Breakdown Testers also known as Hipot Testers or Insulation Testers are a necessity for any Transformer testing, Substation equipment testing, Cable testing, Panel testing and testing of various insulating materials. Insulation testing is very important to ensure and maintain the safety of electrical equipments and also for the safety of operator.
-
Product
Low-Noise Voltage Preamplifier
SR560
-
Stanford Research Systems, Inc.
The SR560 is a high-performance, low-noise preamplifier that is ideal for a wide variety of applications including low-temperature measurements, optical detection, and audio engineering
-
Product
Clamping Voltage Tester
MIG0603CLV1
-
The MIG0603CLV1 is a generator for testing varistors. It has circuits with three different source impedances and up to 11 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 200A which is maintained over the entire load range.
-
Product
Programmable Withstanding Voltage & Insulation Test
LS9923
-
LS9923 programmable withstanding voltage & insulation test system is high-performance testing device special for AC&DC Withstanding Voltage and Insulation Resistance Test, It allows setting the output voltage. The warning value,testing time and some other parameters can be set in the screen.It with a variety of automatic test functions. The testing is quick and high accuracy which is not only applied in the production line but also in the develop research.
-
Product
High Voltage Surge Current Monitors
HVSCM
-
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. In production testing we expect that most of the time the devices will pass. In the event that one should fail, the failed device would be removed and then all the parts would have ot undergo another surge test. Since most devices pass most of the time, simultaneous surge testing can be a real time saver.
-
Product
LXI High Voltage Switching - 20xSPST Plugin Module
65-233-703-HI
General Purpose Relay Module
The 65-233-703-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 7 kV. Switch arrays are created by populating the 65-200-002 scalable chassis with plug-in modules that provide access to the switches on 51-pin front panel connectors. Users can specify as many or as few plug-in modules as they require and can field upgrade the chassis to extend the number of switches.
-
Product
High Voltage Micro-SIL Reed Relays
Series 119
-
The Series 119 is a range of Micro-SIL Single-In-Line reed relays intended for voltages that are beyond the capabilities of conventional SIL reed relays. The 1 Form A, 1kV version is pin and package compatible with the established and popular Series 109P.
-
Product
Voltage Tester, 12V to 1000V, Light
72-2980
-
Non-Contact Voltage Detector Handy accessory detects presence of AC voltage from 12V ~ 1KV, providing clear audio and visual indication. Five segment bargraph display shows relative voltage level. Built in LED flashlight provides added convenience in poorly lit environments.
