-
product
Spring Fatigue Testing Machine
TPJ Series
Jinan Testing Equipment IE Corporation
Model TPJ Series Mechanical Computer Control Spring Fatigue Testing Machine is mainly used for the fatigue properties of all kinds of coil springs, disc springs, shock absorbers, and seal springs etc. The Spring Fatigue Testing Machine consists of motor, reducer on the connecting cams to drive the connecting rod and make reciprocating motion achieve the compression fatigue movement. The Spring Fatigue Testing Machine is efficient without any pollution to the environment. Equipped with different ...show more -
product
Full Band (1200 ~ 1700 nm) Tunable Laser Source
CA9813
This specification describes and defines Advanced Lab Instruments CA9813 full band CW tunable lasers with applications to test and measurement equipment. It provides fast wavelength tuning, high power output, and high power stability. Advanced Lab Instruments tunable laser products support full-band, and other single-band operation. A full-band tunable laser is also available, covering 1200 ~1700 nm wavelength range, with seamless tuning.
-
product
USB-6341, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
781438-01
16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
product
Quality Assurance
Exploratory Test Code Coverage
Exploratory testing is simultaneous learning, test design, and test execution of critical areas in the application. It is an efficient method to provide rapid feedback and uncover critical bugs in newly released features. As these tests are manual and their execution duration is longer and more expensive, it’s important to minimize overlap with other test types. Gain visibility into which code areas are being tested with manual and exploratory tests to improve team efficiency and speed.
-
product
PXIe-1082, 8-Slot, Up to 8 GB/s PXI Chassis
780321-01
PXIe, 8-Slot, Up to 8 GB/s PXI Chassis—The PXIe‑1082 features a high-bandwidth backplane to meet a wide range of high-performance test and measurement application needs. It accepts PXI Express modules in every slot and supports standard PXI hybrid-compatible modules in up to four slots. The chassis features an extended operating temperature range for applications needing cooling performance.
-
product
Tensile Test Methods For Plastics: ASTM D638
Resin materials (plastics) are found in a wide variety of items used on a daily basis. Recently, plastics have started to be used as structural materials in transportation equipment, such as automobiles and aircraft, due to their strength and light-weight nature. In these applications, it is important to understand the mechanical strength properties of these plastics. ASTM D638 specifies methods for testing the tensile strength of plastics and other resin materials and for calculating their mechanical properties, and outlines accuracy requirements for the test frames and accessories used.
-
product
PXIe-8522, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module
787312-01
PXIe, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8522 is a 1000BASE-T1 unshielded twisted pair (UTP) module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications that require Automotive Ethernet to test … and validate automotive electronic control units (ECUs). The PXIe-8522 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act...show more -
product
In-Circuit Fixtures
In-Circuit test fixtures can be configured for dual stage, dual well and opens testing applications. Even the most complex boards can be accommodated using standard methods of actuation.
-
product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 6-Channel, 2-Pole
42-514-104
The 40-514-104 (PXI) and 42-514-104 (PXIe) are low density multiplexers in dual 6-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
Quasar Smart Relay Tester
The Quasar is the most advanced three-phase relay test set designed for the testing of secondary and IEC-61850 protections of any type with special focus on industrial and routine maintenance applications.
-
product
PXI-2598, 26.5 GHz, 50 Ω, Dual-Transfer PXI Transfer Switch Module
778572-98
26.5 GHz, 50 Ω, Dual-Transfer PXI Transfer Switch Module—The PXI‑2598 is a general-purpose switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2598 is also well suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking to predict relay lifetime and reduce unexpected system downtime.
-
product
ATE System Power Supplies
N5700 Series
The Keysight N5700 Series delivers low noise power in a compact 1U package. Airflow moves front to back, so no additional space is required above or below the power supply in your automated test equipment (ATE) rack. Select output voltages from 6 to 600 V. For low current applications, the 750 W models provide 1.3 to 100 A. For higher current needs the 1500 W models provide twice as much current.
-
product
EMBEDDED MMC (EMMC)
SD 3.0 / eMMC 4.51 IP Family
The eMMC Host IP is an RTL design in Verilog that implements an MMC / eMMC host controller in an ASIC or FPGA. The core includes RTL code, test scripts and a test environment for full simulation verifications. The Arasan MMC / eMMC Host IP Core has been widely used in different MMC applications by major semiconductor vendors with proven silicon.
-
product
PXI 3A Power MUX BRIC, 5-Channel, 48-Pole
40-571-005
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
150 A, 10 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 2 meter cable
CP150B
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm - SPST
50-294-123
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
USB-6341, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
782251-01
16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PXI High Density Precision Resistor Module, 9-Channel, 2Ω to 31.5Ω
40-298-110
The 40-298-110 is a high density programmable resistor module with 9 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Reporting Tool for Dynamic Signal Analyzer
m+p eReporter
m+p eReporter is the powerful reporting tool of the m+p Analyzer dynamic signal analyzer. It provides test engineers with comprehensive capabilities for browsing and viewing data, copying & pasting data to ActiveX applications, importing test data from many third-party noise & vibration systems and automating repetitive tasks. This full functionality is available without any measurement hardware connected.
-
product
Production Stand-Alone
PSA
Using PSA, test engineers can build sequences of applications in the built-in AEX (Application EXecutive) manager using if then else goto capabilities. Sequence builders can also include additional capabilities through DOS/Win command line calls, create serial number logged test reports, export tests results to a database etc.. PSA includes drivers for all JTAG Technologies controller hardware past or present.
-
product
PXIe-4142, 4-Channel, ±24 V, 150 mA PXI Source Measure Unit
782430-01
PXIe, 4-Channel, ±24 V, 150 mA PXI Source Measure Unit - The PXIe-4142 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4-wire) sensing for accurate measurements. The fast sample rate of the PXIe-4142 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules.
-
product
(2500kN+) Fatigue Testing Systems
8806
The precision mechanical systems, combined with the advanced features of the 8800 digital controller and Dynacell™ load cells, enable Instron to supply fully-integrated turnkey solutions to meet the most demanding applications. The system can be used to cover a broad range of static and dynamic test applications, covering metals, rebar, high-force fracture mechanics, aerospace panels, civil engineering components, wire ropes, or concrete.
-
product
4-Channel High Speed Position Comparison And Trigger Module
ECAT-TRG4
The ECAT-TRG4 is EtherCAT SubDevice module with high-speed position comparison trigger and encoder single redriver function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications.
-
product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 1.51MΩ
40-298-144
The 40-298-144 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 1.51MΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Channel Replicator
Series 7000
The Series 7000 System is a multi-radio test network which replicates the propagation path of real-world applications. With complete bi-directional capability radios may operate in full duplex mode at distances up to 150 nautical miles.
-
product
80W Power Supply, 8V, 8A or 20V, 4A
E3644A
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features. The Keysight 80W, single output E3644A is a stable and reliable power supply for benchtop and basic automated test applications, and enables versatile solutions for tests that require moderate speed and precision with both GPIB and RS232.
-
product
MLDD 4-Way Power Dividers
KRYTAR MLDD 4-way power dividers lend themselves to emerging wireless ultra-broadband designs and many test and measurement applications. KRYTAR’s power dividers offer the widest frequency coverage in a single package on the market and provides superior performance. Targeting broadband electronic warfare (EW) systems and complex switch-matrix applications, for example, KRYTAR has used its proprietary design to produce a wide assortment of matched-line directional dividers (MLDD) with ultra-high performance over a broadband frequency range. Our 4-way power dividers can also be manufactured to meet military specifications.
-
product
Superior Electromechanical Universal Testing Machine
WDW-S Series
Jinan Testing Equipment IE Corporation
WDW series computer control electromechanical universal testing system for tension,compression, flexure testing is designed according to ASTM, ISO, DIN, EN standards etc.. The electromechanical universal testing system for tension,compression, flexure testing is computer-controlled and precision. Our electromechanical universal testing system for tension,compression, flexure testing is widely suitable for metallic and nonmetallic materials for tension, compression, bending, shearing and low cycl...show more -
product
RF Switch Matrices
For applications involving the test and measurement of multiple RF components, Teledyne Coax offers Custom Switch Matrix solutions to integrate multiple switches, along with additional components including filters, mixers, and attenuators, as required.
