Showing results: 451 - 465 of 491 items found.
-
PA-40 -
Pansco, Ltd
The PA-40 is designed to check both shielded and unshielded twisted pair (STP/UTP) and coaxial BNC-type network cables. With the push of a button, it tests all wires for continuity, miswiring, and polarization. Dual-colored LEDs let you identify correct and reversed pairs; using the included remote unit, cables may be tested before installation or after installation. Features tip/ring polarity test. Uses 1 9V battery.
-
DSA DOCSIS -
Rohde & Schwarz GmbH & Co. KG
Only the highest signal quality ensures maximum throughput. The R&S®DSA DOCSIS signal analyzer has been designed to support users by ensuring the highest signal quality. DOCSIS is the standard for transmitting IP data within hybrid fiber coaxial (HFC) cable TV networks.
-
7A -
Picoprobe
An unterminated version, can be used for capacitance and resistance measurements or in low to medium speed signal applications where a 50 ohm termination is not required. A flexible coaxial cable length of 6 feet in length is standard on the Model 7A; however, when used for capacitance measurements, GGB Industries, Inc., recommends using a shorter 3 foot cable. If a shorter length of cable is desired for capacitance measurements, please specify it when ordering (Model 7A-3ft.). Please note that Model 7A uses Model 7 replacement tips.
-
PH-100/120 -
Pansco, Ltd
The Lantracker is a network tester, pin-by-pin cable tester, and tone generator all in one. As a network tester, it detects whether a network is active or inactive and displays network speed (10/100/1000 Mbps) in either case. It also flashes the network hub or NIC’s port light corresponding to the cable it is connected to, to show the cable’s port number. As a cable tester, it performs loop-back or remote tests of network, data, voice, and coaxial cables, displaying the results on a pin-by-pin LED display which moves from pin to pin automatically or manually. The Lantracker can be used to test cable or shield integrity, testing network function and speed, and tracing cable using its tone generator function (tone probe not included). Includes an adaptor for testing coaxial-F cable. Uses 1 9V battery.
-
Optomistic Products
The Universal LightSources use a standard 5-volt DC power supply connected via a connecting cable with mating coaxial power plug and terminated with clearly polarized push-on connectors to access fixture 5-volt D.C. supply wire-wrap pins wherever available. Alternatively, the Universal LightSource can be connected to a serial-digital pulse-code-modulated signal source.
-
Fairview Microwave Inc.
Waveguides from Fairview Microwave consist of coaxial adapters, bandpass filters, bends, flexible waveguide cables, waveguide gain horns, sections and terminations. Fairview waveguides are available in standard sizes from WR-430 through WR-15 depending on type of waveguide product, which encompasses frequencies from 1.7 GHz to 75 GHz.
-
F9 Systems, Inc.
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
EOCM-7102 -
Hangzhou Softel Optic Co., Ltd.
EOCM-7102 is the outdoor EOC Master of the EOC (Ethernet Over Coaxial) solution. It is in compliant with HomePlug AV standard. The EOCM-7102 have two EOC module. It provide two TV input, two com output and two 10/100/1000M auto-negotiation uplink ports. It offers the high-speed data service to the customer based on the coaxial cable network. The EOC module in the EOCM-7102 is based the Qualcomm AR7410 chipset solution, with high anti jamming capability OFDM technology. The 7.5-65Mhz low frequency band is used for EOC signals. Built in high isolation filter as CATV RF and EOC signal mixer, the EOC signal and CATV signal in 87~862Mhz can running on one cable without interference. The EOC Master can provide high speed data service. The PHY Layer speed is 600Mbps, the MAC Layer throughput is up to 320Mpbs.
-
780988-01 -
NI
The PCB GPTC03 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the … Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB GPTC03 features a sensitivity range of 10 mV/g and requires a low-noise coaxial cable.
-
780989-01 -
NI
The PCB HSTC33 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB HSTC33 features a sensitivity range of 100 mV/g and requires a low-noise coaxial cable.
-
PCA900 -
Lectrosonics, Inc.
A unique and very useful design, the PCA900 antenna provides wide bandwidth from 825 MHz to 1 GHz, moderate gain of 3.7 dB and a semi-directional polar pattern in a compact, rugged package. A BNC connector allows direct connection to receivers and multicouplers with standard 50 ohm coaxial cable. This antenna is an ideal match for systems in the 902-928 MHz and 941-960 MHz ranges.
-
Cryogenic Ltd.
The Resistivity System allows the user to make Resistivity and Hall Effect measurements in the range of to M. Samples are mounted on special platforms inside the VTI with contacts made to the sample according to the customer's requirements. Connections at the top of the probe are made via Fischer Connectors or Coaxial Cables. Keithley source and measurement electronics are provided with the system. These are fully controlled using the Measurement System Software.
-
MT-7058 -
Prokit's Industries Co., Ltd.
Complies with CE safety standardAutomatically detect good connections, opens, crossed wires & split pairsTest RJ45 TIA568A/B (AT&T) 258A), 10 Base-T, Token ring, RJ-11/RJ-12 USOC and coaxial BNC cablePin to pin cable map indicatorNon-contact voltage detection for user safetyTraces wires with tone & remote lights allows one person operationCompact size and lightweight design for easy to carry aroundCircuit Protection for both units to ensure the testing qualityLow power consumption with auto power off function to preserve batteryLong cable test more than 300 meters
-
NileCAM30_TX2 -
e-con Systems Inc.
NileCAM30_TX2 is the four board solution containing the camera module, serializer, deserializer and TX2 base board. This camera is based on AR0330 CMOS image sensor from ON Semiconductor®. The NileCAM30_TX2 comes with 3 meters or 15 meters coaxial cable with FAKRA connector at both ends of serializer/deserializer board. The NileCAM30_TX2 has an S-mount (M12) lens holder which allows customers to choose and use the lens according to their application requirement.
-
PHD-4001A -
High Power Pulse Instruments GmbH
*Electrically isolated probearm kit for VF-TLP, TLP, HMM, HBM force and sense probingbased on the GGB Picoprobe Model 10 replacement probe tips*Buried coaxial cable channel for thermo-chuck in isolated chamber temperature measurements*Compatible with GGB Picoprobe Model 10 replacement probetips*Compatible with all standard micropositioner interfaces*High precision rotation of the probearm by backlash-free 80:1 gear*Rugged stainless steel design*SMA connectors
