Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
8-CH Relay Outputs & 8-CH Isolated DI PCI Cards
PCI-7250/7251
-
ADLINK's PCI-7250/7251 provide 4-CH SPDT (Form C) & 4-CH SPST (Form A) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are nonpolarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments. The PCI-7251 is an 8-CH relay outputs and 8-CH isolated DI extension card of the PCI-7250. All the I/O functions of PCI-7251 are the same as those of the PCI-7250. The PCI-7251 has to be connected with PCI-7250 and the bus interface is controlled by the PCI-7250. Up to three PCI-7251 cards can be connected to one PCI-7250, therefore, expanding the PCI-7250's DIO from 8 DIO to maximum 32 DIO.
-
Product
PCI 16 Reed Relay Output / 16 Isolated Input Digital Interface (10-30V)
8004H
-
Optimized for sensing up to 24V inputs, the 8004H PCI digital I/O interface provides 16 optically isolated inputs and 16 Reed relay outputs. The inputs protect the computer equipment from spikes and ground loop current that can be generated in industrial environments, while the outputs provide high quality, long-life, low-current (10 Watt maximum), dry contact switch closures. The relays are normally open, and close when energized.
-
Product
Mixed Signal Oscilloscope 500 MHz, 4 Analog Plus 16 Digital Channels
MSOX3054G
-
The MSOX3054G 500 MHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Analog I/O module with 8 differential analog output channels
IO108
-
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 8 output channel has its dedicated D/A converter with an update time of 2.2µs. The output coupling of the module can either be ordered as differential or single-ended. Furthermore, several of these modules can be interconnected by trigger lines to synchronously update analog output channels among the different modules.
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787453-01
-
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a … high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
WaveRunner Oscilloscope, 2.5 GHz Bandwidth, 4 Input Channels, 20 GS/s on 2 Ch Sample Rate
WaveRunner 9254
-
2.5 GHz, 20 GS/s, 4ch, 16 Mpts/Ch DSO with 15.4" Capacitive Display.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 4 GHz, 4 Analog Plus 16 Digital Channels
MSOS404A
-
4 GHz bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.2 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
WaveSurfer Oscilloscope, 1 GHz Bandwidth, 4 Input Channels, 4 GS/s, 20 Mpts/ch - interleaved
WaveSurfer 3104z
-
1 GHz, 4 GS/s, 4 Ch, 10 Mpts/ch DSO with 10.1" Wide screen Color, Capacitive Touch Screen Display.
-
Product
Oscilloscope, 350 MHz, 4 Input Channels, 5 GS/s interleaved, 250 Mpts - interleaved
T3DSO3354
-
350 MHz, 5 GS/s interleaved, 4 CH, 250 Mpts/Ch interleaved, DSO with 10.1" Color Display.
-
Product
Modbus RTU Analog Input
-
Provide direct connection to a wide variety of sensors to any host with an RS232 or RS485 port. The modules perform all signal conditioning, scaling, linearization, and A/D conversion. They each contain some discrete digital I/O lines and can measure signals such as:
-
Product
16-Ch Digital Input Modules
ADAM-5051
-
Input voltage: 30 VmaxCircuit type: Pull-Up current: 0.5 mA (Source Type)Power consumption: 0.53 WChannels: 16
-
Product
PXI-6513, 64-Channel, ±30 VDC, Sink Outputs, Bank-Isolated PXI Digital I/O Module
778971-01
-
64-Channel, ±30 VDC, Sink Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6513 is an industrial digital output interface with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6513 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-Purpose Digitizer - 125 MS/s on 12 Channels, 80 MS/s on 24 Channels, 24 Single-Ended Inputs, 12 True Differential Inputs
DN6.596-24
-
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
NI-9421 , 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
779136-01
-
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
Product
Programmable Linear DC Power Supply, 1 Output, 0-16V/0-8A
T3PS16081P
-
Programmable Linear DC Power Supply, 1 Output, 0-16V/0-8A.
-
Product
PCI Express 16 Reed Relay Output Digital Interface
8003e
-
The 8003e PCI Express digital I/O interface provides 16 Reed relay outputs. The outputs provide high quality, long-life, dry contact switch closures suitable for low-current applications up to 10VA. Reed relays are normally open and close when energized. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
Complete Input Solutions
-
We can help your ideas to become reality. With extensive consultation and support, Hoffmann + Krippner can offer everything needed to design and produce your ideal input device, including beautiful designs, exact and reliable electronics, optimal mechanics, and software solutions. In cooperation with OKW (as a joint venture partner) and TES-Frontdesign (as part of the Hoffmann + Krippner Group), we can provide a wide array of beautifully-designed, cost-effective enclosures and corresponding components, including stainless steel or aluminum enclosures.
-
Product
LXI Reed Relay Matrix - Single 128x4 Plugin, No Direct Y Access, 6 Analog Buses
65-221-112
-
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Isolated 16-Bit Analog Output Board
MSXB 076
-
The Microstar Laboratories Isolated 16-Bit Analog Output Board, part number MSXB 076, provides isolated analog outputs for Data Acquisition Processor (DAP) systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – as well as to eliminate phase errors from analog outputs in your application.
-
Product
PXI 8 Slot BRIC 506x8 1-Pole Dual Analog Bus (11 sub-cards)
40-560A-121-506X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
120 W 16.5 - 50 VDC 5 outputs PSU PCI/104 SFF
PCI104-SFF-IPSU-16-50-C
-
This rugged isolated power supply is capable of supplying up to 120 watts of power output for a range of sensitive defense applications as well as industrial applications - with conformal coating.
-
Product
PXI-6512, 64-Channel, ±30 VDC, Source Outputs, Bank-Isolated PXI Digital I/O Module
778969-01
-
64-Channel, ±30 VDC, Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6512 is an industrial digital output interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6512 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
8-Channel, 10 MHz Precision ReferenceWith Sine and Logic Outputs
ITS-6200
-
The ITS-6200 is a versatile 10 MHz laboratory frequency reference useful for synchronizing test instruments to a common standard. Eight outputs are provided, each which can be configured independently as sinewave or logic level square-wave signals. Additionally, CMOS logic levels can be set for 5V, 3.3V, or 2.5V logic family compatibility. A 10 MHz reference input is provided to phase lock the ITS-6200 to an external reference, such as a GPS or Rubidium standard, or cascade multiple ITS-6200 units for additional outputs. The low phase noise and high stability OCXO within the ITS-6200 is suitable for the most demanding applications, whether free-running or phase locked. The compact size and low power consumption makes the instrument highly portable and suitable for AC-powered operation in the lab or battery operation in mobile or field applications.
-
Product
Analog I/O Boards
-
General Standards Corporation is a leading supplier of a wide range of high speed Analog I/O boards for embedded applications on several form factors/buses, and for many operating systems. See our selection tables below.
-
Product
LXI Reed Relay Matrix - Single 32x32 Plugin, No Direct Y Access, 1 Analog Bus
65-227-101
-
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
Multiple Output Bidirectional PSU
LAB-MOBI
-
Electronic Test & Power Systems
The LAB-MOBI is a series of multi channel High Power Bidirectional PSUs. Each system is able to operate as either a DC Source or a DC Electronic Load. This integrated approach features high dynamics enabling the user to switch seamlessly between quadrants. When sinking energy from the unit under test the LAB-MOBI automatically inverts the DC to AC and synchronises this output to the grid. Dedicated application modes are available for battery cycling and emulation, which can be used to implement specific test routines. Other common applications the LAB-MOBI is used for include testing electric motors, fuel cells, super capacitors and solar panels. Max. Volt. Output 1000V,Min. Power 60kW, Max. Power 500kW.
-
Product
Bench/System/ATE Programmable DC Power Supply Single Or Dual Outputs, 360 To 840 Watts, With Or Without Remote Interfaces
CPX Series
-
PowerFlex design gives variable voltage and current combinations within a maximum power rangeUp to 60 volts and up to 20 amps180 watts or 420 watts maximum per outputIsolated outputs can be wired in series or parallelConstant voltage or constant current operationSettings Locking (S-Lock)PowerFlex or fixed-range operationVariable OVP tripsSelectable remote sense terminalsCompact quarter or half rack 3U case sizeIsolated analogue remote control (CPX400SA only)RS232, USB & LXI compliant LAN (P models only)GPIB Option (P models only)
-
Product
80W to 170W - Multiple Output
ZWQ Series
-
*Low Profile (1U height)*Universal Input*PFC: Conforms to EN61000-3-2*EN55022 Curve B*Forced Air or Convection Cooled
-
Product
Pressure Transmitter For Industrial Applications, Ratiometric Output
Series 21 C
-
KELLER AG für Druckmesstechnik
The C-series transmitters are noted for their ability to deliver high accuracy over a wide temperature range. This is achieved by means of mathematical modelling of the sensor characteristics and digital compensation. In order to do this, each transmitter is gauged over pressure and temperature, programmed and checked after calibration in the same test set-up.
