Tachometers
Measure number of rotations over time.
See Also: Tachometer Testers, Engine Tachometers, Motor Rotation
-
Product
Contact Type Handheld Digital Tachometer
HT-3200
-
The HT-3200 offers a Lo measurement range that starts from 0.5 r/min. The circumferential ring and contact tip for rotation measurement can be stored in the back-side pocket of the main body.
-
Product
Tachometers/Stroboscopes
-
Shenzhen Graigar Technology Co.,Ltd.
Used to calibrate or check the speed of centrifuges and other equipment that rotates or vibrates.
-
Product
Digital Tachometer
KM- 2234BL / KM 2235 B / KM 2241
-
Kusam Electrical Industries Limited
Digital Tachometer uses latest technology for accurate measurements. It has Exclusive one chip of Microcomputer LSI Circuit, It is housed in tough ABS case & has ergonomic design for easy holding in the hand.
-
Product
8-Channel VME Tachometer
V360
-
The V360 is a single-width, 6U height VME module designed specifically to acquire low frequency inputs from industrial speed sensors. The module can measure frequency and period over a wide dynamic range, and is specifically designed to ensure reliable measurement in high-noise industrial environments.
-
Product
Tachometers/Torque Meters
-
Tachometers measure rotational or linear speed and come in two styles: contact and non-contact. Contact models come with various rubber/plastic adapters for interfacing the instrument’s shaft with the surface of the spinning or moving surface under test. Non-contact models come with reflective tape that is placed on the surface to become the target of the instrument’s low-power laser.
-
Product
Tachometers
-
Labs use this high accuracy unit to check speeds of centrifuges, motors, or stirrers. Five digit LCD is a vivid ½-inch high display. Tachometer takes only three seconds for most readings. A unique memory feature permits recalling the highest, lowest, and last reading. Unit is extremely easy to use; operation may be learned in one minute. One end of the unit provides contact readings with a rotating spindle.
-
Product
EZ-Tach Digital Automotive Tachometer
325
-
The EZ-Tach makes RPM measurements quick and easy. This is a very useful tool for tune-up and other diagnostic work where accurate RPM readings are required. Just clamp over any spark plug wire and get accurate RPM on conventional or DIS ignition systems. The unit also features a data hold function. The large 2000 count LCD display shows; RPM, function, data hold indication and low battery indication. The EZ-Tach is powered by one 9 volt battery. Battery and instructions are included.
-
Product
Process Panel Meters
-
Rugged and reliable, the 1/8 din panel meter line is designed for both the OEM and retrofit markets with an array of flexibility enabling usage in a broad range of applications. Our Panel Mount Tachometers are ideally designed for speed, rate or time monitoring applications with potential connection to PLC’s and networks with available outputs. The dedicated Process Meter line-up allows usage in virtually any application with their voltage, current or temperature input selections along with a myriad of optional output signal and communication combinations. The similarly designed Process Counter line completes the offering, geared for frequency or encoder input applications.
-
Product
Photo/Touch Type Tachometer
DT-2856
-
measurement range rotative velocity: 2.5～99,999r/min (laser) 2.5～19,999r/min (touch) resolution:0.1/1 accuracy:±(0.05%n+1d) memory: max/min/last value power supply:4x1.5v aa(um-3)battery dimension:215x74x32mm
-
Product
5000
White Series
-
The Equus 5000 series white 5" pedestal mount tachometer offers excellent street performance value featuring classic performance tach design, compatibility with most 4,6, and 8 cylinder engines equipped with conventional peformance ignitions.
-
Product
Tachometer Tester
TG23P
-
Aircraft Development Industries cc
The model TG23P is an entirely solid state digital 3 Phase, 2 pole, Tachometer Generator Simulator. There are no motors, strobe lights or moving parts in the unit which makes it ideal for testing electro-mechanical type Tachometers, Percent RPM Indicators, Dual and Triple Tachometer indicators
-
Product
Calibration Units
-
Optical Stroboscope and Tachometer European Calibrator Unit was originally designed for in-house test and calibration of our comprehensive range of Digital Optical Tachometers, Optical Speed sensing products and Stroboscopes.
-
Product
DIGITAL TACHOMETER
IBL-DT2235A
-
International Biological Laboratories
This is a Digital Hand Held Contact type Tachometer and has Micro Computer LSI Chip
-
Product
NI-9234, 4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module
779680-03
Sound and Vibration
4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module - The NI‑9234 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9234 is also compatible with smart TEDS sensors. The NI‑9234 delivers a wide dynamic range and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
8-Channel VME Tachometer
V365
-
The V365 is a single-width, 6U height VME module designed specifically to acquire low frequency inputs from industrial speed sensors. The module can measure frequency and period over a wide dynamic range, and is specifically designed to ensure reliable measurement in high-noise industrial environments.
-
Product
Digital ICP® - USB Signal Conditioner
-
The Digital ICP®-USB Signal Conditioner, Model 485B39, offers plug-and-play connectivity for your measurements. Model 485B39 from The Modal Shop, a wholly owned subsidiary of PCB Piezotronics, is a pocket-sized, dual-channel ICP to USB digital signal conditioner. The unit provides any ICP sensor – accelerometers, microphones, impact hammers, laser tachometers, and more – with a digital USB output. It is truly plug-and-play, with no drivers required. Digital ICP features two BNC inputs and a 24-bit USB digital signal output, allowing a direct connection from the sensor to any PC, tablet, or smartphone device for easy data collection, analysis, and sharing on-the-go.
-
Product
CONTACT CUM NON CONTACT DIGITAL TACHOMETER
IBL-DT2236
-
International Biological Laboratories
This is a digital contact cum Non Contact combined, Hand Held Tachometer.
-
Product
Frequency, Rate Meter, Flow Rate Indicator
-
Two independent scalable pulse-input channels from 0 Hz to 1 MHz. Channels may be combined arithmetically. One channel can display total while other displays rate. High read rate for control applications: AC line frequency can be measured to 50.0000 or 60.0000 Hz in a few line cycles. Ideal for use as a tachometer or readout of a turbine flow meter.
-
Product
Sensors
-
SHIMPO INSTRUMENTS offers a variety of sensors and rotary pulse generators to send various trigger signals to panel tachometers, counters and stroboscopes. When coupled with the appropriate SHIMPO panel meter or stroboscope, our sensors can be used in many different operating environments from laboratory to hazardous Class I -Group C&D and Class II- Group E, F, & G.
-
Product
Ignition Pulse Detector
IP-3000A
-
IP-3000A Ignition pulse detector is a slim and light weighted detector by using amorphous metals fiber element. It is 1/4 in thickness (mass: approx. 1/50) and 1/3 in weight compared with the previous model of Ono Sokki. Also the IP-3000A can obtain constant output from low to high rotation with high sensitivity.Meeting the needs of structure or mechanism in recent gasoline engines, the IP-3000A can easily clamp around an ignition coil cable (the primary side cord of ignition coil or the current cord of electronic distributor). Moreover, heat-resistant design up to maximum operating temperature of +120 C° enables measurement under harsh environment.The IP-3000A Ignition pulse detector can be used with Ono Sokki’s engine tachometer.
-
Product
USB Sound And Vibration Measurement Bundle
Sound and Vibration
The USB Sound and Vibration Measurement Bundle provides a portable, USB-based sensor measurement system that helps you measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes.
-
Product
Handheld Tachometers
-
The handheld tachometer is a means of measuring revolutions within the industrial sector, either optically or mechanically. The handheld tachometer can be used for maintenance and calibration of machines that have moving parts. The principle is similar to a bicycle speedometer, where time will be measured until a wheel has completely turned. The handheld tachometer has two different measurement methods.The handheld tachometer may have a contact connection to the moving parts. Alternatively, the handheld tachometer works with reflecting marks. This will be secured on the moving part. As the laser strikes the reflecting mark during rotation, it will be reflected and detected in the handheld tachometer via a sensor. Rotation speed and speed can be seen on the handheld tachometer. The handheld tachometer may combine both possibilities (contact and non-contact connection). Next to the handheld tachometer you find other devices for measuring revolutions at PCE Instruments.
-
Product
TAKCAL Tester
H391T-56-1
-
Measures and displays individual tachometer speeds in percent RPMConnects at flight deck navigator station for signal and at St245 for power
-
Product
Tachometers
-
An instrument that measures the working speed of an engine (especially in a road vehicle), typically in revolutions per minute.
-
Product
Analysis In Real Time
Live Analyzer
-
Vibration Research Corporation
With Live Analyzer, you don’t have to wait until post-process to begin data analysis. View data in real-time and then pause the live stream to select, analyze, and export a section of the time waveform. Access the ObserVIEW graphing packages, employ averaging, analyze tachometer channels, and more.
-
Product
Speedometer Test Bench
-
Maschinenbau Haldenwang GmbH & Co. KG.
Tachometer tester for cars and commercial vehicles.
-
Product
Hand-held Tachometers
-
SHIMPO offers a wide range of hand-held tachometers that measure the total number of revolutions of a shaft or number of pulses of reciprocating equipment. Our models can measure and record last/min/max and up to 10 reading using up to 16 different units of measure. Our tachometers are designed for applications such as Motor Speed/Conveyor Speed/Fan Speed/Length Measurements that measure rpm of motors or shafts, either contact or non-contact with Laser style combination tachometer.
-
Product
Ignition Pulse Detector
IP-292/296
-
These detectors are electromagnetic induction type detector designed to detect the number of ignition pulses produced in the gasoline engines. The IP-292 pinches a primary cord (low voltage) and the IP-296 pinches a secondary cord (high voltage) of the ignition coil. The compact, light-weight and clip-on design of these detectors offer a simple and easy detection of the number of pulse. Since the detector and its cord are made of heat resistance materials, these models are not affected by the high temperature in the engine room. These detectors are used with the engine tachometers made by Ono Sokki. (AR-7240B, CT-6700, HT-6200, SE-1620, FT-2500 or GE-2500)
-
Product
Professional Automotive Digital Multimeter
CT8027
-
Full autorange features. Large 4 digit LCD display with analog bargraph. AC/DC Voltage measurement up to 600 Volt. AC/DC Current measurement up to 10 A. Tachometer function with inductive pickup measures from 30 to 20000 rpm
-
Product
Tachometer Tester
Series 1921
-
The Model 1921 Tachometer Tester is used for the testing and calibration of electrical and mechanical tachometer generators and indicators.
