AC Electronic Loads
Simulate voltage, current and power ranges.
-
product
Three Phase Phantom Load Test Bench
Supreme Instrument Laboratories
Supreme make Phantom Load Test Set is a portable testing accessory designed for field service. It simulates various load conditions usually prevailing in power supply system. The unit offers a practical solution by providing artificial load unaltered by the variation in the power supply mains and adjustable to the complete meter testing requirements.
-
product
AC and DC Non Inductive Current Shunt
Series A co-axial shunt and Option 02F/B shunt
Use with wattmeters, DMMs and power analyzers to extend current measurement ranges. Use with phase angle meters to enable phase angle measurements between voltage and current. Ultra low phase shift
-
product
Water Cooled Active Resistance DC Electronic Load
WRx Series
Utilizing Magna-Power’s new patent pending Active Resistance Technology in combination with the company’s internally manufactured microchannel water-cooled heatsinks, the WRx Series addresses high power DC applications where exhaust heat control is essential. The WRx Series greatly increases power density compared air-cooled alternatives. An integrated solenoid controls the flow of water to avoid condensation. Full power can be achieved using conventional water, with water inlet temperatures up to 25 °C.
-
product
Hand-Held 12 Volt Combo Digital Load Tester
6028DL
• 60 Amp load to test smaller batteries: CCA and Amp hours• 125 Amp load to fully test larger batteries: CCA and Amp hours• 125 Amp clamps offer greater flexibility when attaching the hard to reach applications • Made in USA of US and Global Components
-
product
VBR Load Analyzer
The Powerohm Variable Braking Resistor Analyzer will determine what braking resistor ratings are required for your specific application. The Powerohm VBR is a portable test unit that provides selectable steps of resistance for analyzing your braking requirements for a wide range of drive horsepowers. Simply connect the VBR to your drive or braking module and let the application decide what braking resistor it needs. Once you determine the optimal resistance value for your drives peak performance, the VBR's digital readout will accurately display the true duty cycle as the application runs.
-
-
product
Performance AC Power Source, 375 VA, 300 V, 3.25 A
6811C
Maximize your investment with five instruments in one device Increase your productivity with extensive built-in power measurement capabilities Flexible IO: LAN/LXI Core, USB and GPIB Lower your cost of ownership with global support & the longest standard warranty in the industry
-
product
Programmable AC Laboratory Power Supplies, Current-controlled
*Fast regulation of the current*Voltage depends on the load*Current and voltage values are configured based on the customer's actual requirements*Power from 250VA to 36kVA*Output voltages 1VAC to 300VAC*Maximum currents up to 2000A per phase
-
product
Economical Single Point Bending Beam Load Cells
ESP SERIES
The ESP Series is a economical, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point bending beam design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The ESP Series features a moisture proof sealant.
-
product
AC Clamp-On Ammeters
STB Electrical Test Equipment, Inc
STB manufactures analog, clamp-on Ammeters intended to read electrical current in a circuit. This hands-free design provides a fast and accurate reading and allows users to clamp onto any size conductor with various jaw opening options. The ammeters easily attach to a hot stick with a clamp-on adapter installed by STB.
-
product
Static Load Cells (5 N to 300 kN)
2530 Series
The Instron 2530 Series static load cells are precision force transducers engineered for versatile use in tension, compression, cyclic, and reverse stress testing, delivering accurate measurements down to 1/500th of their capacity. Individually temperature-compensated and calibrated, they support automatic recognition and electronic calibration, and are built to international force-measurement standards (ASTM E4, ISO 7500-1 class 0.5, and JIS B7721, B7733). With overload protection (150 % of rating without damage, 300 % without mechanical failure), the 2530 family offers consistent, repeatable performance across a wide force range (5 N to 300 kN).2530 Series load cells with capacities of 5 N to 100 N are for use with 3300, 3400, 5900, and 6800 Series testing systems.2530 Series Load cells with capacities of 500 N to 300 kN are for use with 3300 and 3400 Series testing systems.
-
product
16-Channel VME AC Power Analysis Module
V180
The V180 is a single-width VME module that allows accurate and comprehensive measurement of AC power circuits. The V180 acquires powerline current and voltage inputs using approved current transformers and model C750 remote potential transducers.
-
product
High Voltage Reed Relays from Pickering Electronics
Pickering Electronics' High Voltage Reed Relays are well suited for Instrumentation, Industrial Process Controls and General Purpose requirements. *Ideal for high-power applications*Plastic package with internal mu-metal magnetic screen*3V, 5V, 12V or 24V coils, diodes are optional*Dry instrument grade switches*Pickering's SoftCenter technology
-
-
product
Load Measuring Pins
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
product
Load Cell DIN Rail Signal Amplifier
LCD20
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
-
product
Three-Phase AC Power Source 320 Vrms, 18 KVA, 5000 Hz
AC6918H
Keysight’s AC6900 Series three-phase power sources provide a complete AC and DC power solution by combining the capabilities of a multimeter, harmonic analyzer, and power analyzer in one instrument.
-
product
Centor Touch Star R,advanced force gauge external load cell
CNR CTR
Centor Touch Star is the most advanced force gauge currently available, it has become the benchmark tool for force measurement. Functionality, accuracy formerly reserved for expensive and complex material testing equipment are now available with Force Gauges. The functionality of material testers previously reserved for research or development applications are now available to the production floor with the introduction of the Centor Touch Force Gauge.
-
product
Electronic Ballast Tester
WT4000
• Measure parameter: 1) Input: Vrms, Lrms, W, PF, Hz, Phasic angle, total harmonic and 0-39 component of harmonic. 2) Output: Lamp voltage, Lamp current, Filament current, Guided cathodic current, Lamp power, crest factor and oscillatory frequency, single high frequency analysis. • Startup: Startup lamp voltage, lamp current, filament current, guided cathodic current curve and parameter, preheating time; • Simultaneously display on 8 windows for input and output parameters, convenient for comparison and analysis; • Test preheat energy, filament preheat time. And the parameters changes from 0 to 5s of filament voltage, filament current and filament power; • Up to 1MHz lrms test content to every EB; • Analysis symmetry of high Frequency curve of lout; • 12-bit high-speed A/D, sampling rate up to 10MHz, can easily analyse signal curve of output; • Finish an input and output testing at the same time within 1 minute; • Portable, can test, display, print without computer. Test report include data and curve, comply with international standard; • Communication port for PC, run under Windows98 or Windows2000, English Version available.
-
product
AC Current / Leakage Digital Clamp-on Tester
MCL-500DFN
MULTI MEASURING INSTRUMENTS Co., Ltd.
MCL-500DFN AC Current / Leakage Digital Clamp-on Tester
-
product
Electronic Control Units
Delivers high-performance real-time control, functional safety, and exceptional flexibility, making it ideal for demanding applications in off-highway machines and non-road vehicles.
-
product
AC Hipot w/ Ground Bond Test Capability
HypotULTRA® Series
In a world where data is king, HypotUTLRA improves traceability with on-board data storage and allows you to automate hipot testing with a variety of communication interfaces. Increase efficiency with our direct barcode scanner connection and intuitive touch screen interface. Models 7804 and 7854 are a 4-in-1 solution with the addition of 40A AC Ground Bond test capability added to HypotULTRA's already impressive feature list. HypotULTRA is a dielectric analyzer designed to take your production line to the next level.
-
product
24-600V AC / 6-220V DC LED Display Voltage Tester
1864
Peaceful Thriving Enterprise Co Ltd
This voltage tester has multiple functions. It's perfect for solving numerous problems occurring in the household, workshop, auto and hobby areas.
-
product
Clamp type AC Current Sensor／for Power Monitor
ZCT-23
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 0.1A～120A*Current measurements of terminal feeder
-
product
On Load Tap Changer Analyzer
TAP4
The TAP-4 is the first instrument to use vibro-acoustic measurement to perform tests on On-Load Tap Changers (OLTC). The TAP-4 is a universal device, it adapts itself to any type of transformers: MR Reinhausen, ABB, Ferranti, Federal Pioneer and others.
-
product
Electronic Dosimeters & Readers
Readers operate using software packages installed on computer (PC) and communicate with DMC 3000 dosimeter and DMC 2000 and SOR families in hands-free data exchange mode. the LDM 320 reader is used as an interface to activate a dosimeter (to switch into counting mode) or to deactivate it (to switch into pause mode). When used with the included* DMCUser software, it functions as an interface to read and write the internal data of the DMC 3000, SOR and DMC 2000 dosimeters.
-
product
AC Power Supplies
BLC Series
The BLC Series delivers all the quality features our customers have come to expect from Behlman; clean sine wave output with excellent line and load regulation, high efficiency and low harmonic distortion. A multi-pulse input transformer offers low-input harmonic distortion and high power factor as required by European standards. Unique protection circuitry provides for over-temperature protection; short-circuit protection and voltage fold-back during overloads to maintain undistorted waveforms.
-
product
Battery Load Tester
Battery Beak
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
product
Battery Load Banks
Kongter Test & Measurement Co., Limited
Kongter offers many different models of battery load units for real capacity test in various industries. With our customized solution, users of different applications will find their exact models as per their needs. With its optional DAC (Data Acquisition Case), you could easily monitor voltage of each cell on PC during battery discharge test.
