High Voltage Amplifiers
-
Product
3-Phase AC Voltage Transducer
ENVIROMUX-PT3-600
-
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.
-
Product
High Voltage Probe: Single-Ended
-
A high voltage single-ended probe is typically used for measuring ground referenced signals up to 40 kV. However, some single-ended probes are designed for oscilloscopes with isolated or floating inputs for measurements that are not ground referenced. Users should select probes with a low input capacitance specification (< 4 pF) to minimize the probe’s loading effect on the circuit because a probe with lower input capacitance will offer higher input impedance at higher frequencies.
-
Product
DC Josephson Voltage Standard
-
The system enables a number of calibration and measurement functions for dc voltages:*Calibration of secondary standards*Calibration of linearities and accuracies of dc voltmeters in the measuring range from 0 to ± 10 V.*Extremely exact output of any reference voltages*Direct comparison of two voltage standard measuring systemsNo other measuring system in the world offers such a variety with the highest precision.
-
Product
Five Channel Amplifier
-
Teledyne RF & Micrrowave designed the Five Channel Amplifier specifically for a custom space application. Each independent channel used dedicated RF Input/Output and DC bias connections. Each channel's RF performance was tailored differently to meet the application requirements. All components were manufactured and screened per MIL-PRF-38534, Class K. Additionally, to meet mission requirements The top assembly was also tested for RF and DC parameters during MIL-STD-202 thermal cycling and random vibration environments. This effort required disciplined development, manufacturing and program management efforts to meet challenging mechanical and RF engineering requirements.
-
Product
High Power Connectors
-
High power connectors are offered in ruggedized, single and multi-way formats with power up to 1,200 Amps that provide excellent performance in harsh environment conditions.
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-905-HI
Multiplexer Module
The 65-231-905-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Low Voltage Differential Signaling (LVDS)
-
Available in QML-Q and QML-V processing flows, CAES LVDS solutions meet all of the stringent mechanical qualification requirements defined in MIL-PRF-38535.
-
Product
AC Voltage Sensors
-
Continuously monitor single or three-phase power lines for over or under voltage conditions with DARE?s AC voltage sensors, voltage monitors, and voltage sensing relays. DARE?s complete line of AC Voltage Sensors will protect system equipment and circuitry from voltage that is hazardous or unsuitable for operation.
-
-
Product
High Power Devices
-
SemiProbe configures our PS4L Adaptive Architecture into the Voltarus (TM) family of probe stations to fulfill the unique requirements of testing high power devices at wafer level prior to packaging. Voltarus probe stations are available in manual, semiautomatic, and fully automatic configurations that can test and characterize power devices up to 10 KV or 200 Amps (pulsed).
-
Product
Uniload Voltage Transformer
2J4-4
-
The Type 2J4-4 Knopp Uniload Voltage Transformer Test Set consists of three major parts:
-
Product
Single Phase And Three Phase High Voltage Test Bench Type KP-V3000-A
-
Bofa Instrument & Equipment Co., Ltd
Electricity meter high voltage test bench KP-V3000-A is a new generation of high voltage testing equipment based on the latest international standards, which adopt special current transformer and high voltage relay to ensure high accuracy and safety.
-
Product
Non-Contact Voltage Tester With Wire Stripper
5227
-
Peaceful Thriving Enterprise Co Ltd
This product combines most required tools for an electrician to do the wiring job within the building, which includes screwdriver, non-contact voltage detector, illumination and wire stripper for most type wires.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-333-HI
Programmable Resistor Module
The 40-230-333-HI (PXI) and 42-230-333-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 52.4kΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-903-HI
Multiplexer Module
The 65-231-903-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Precision Voltage and Current Sources
VI-700
-
The VI-700 Voltage and Current Source is a versatile precision dialable or remotely programmable voltage and current source. Its three ranges provide up to 20 V full scale (200 V with the HV option), and down to 100 mV resolution; and 20 mA full scale down to 0.1mA resolution. Both voltage and current outputs are available simultaneously. The output is set by a range selector and thumbwheel switches in the LOCAL mode, or by a digital input at the rear panel. The REMOTE mode control can be a RS232 or IEEE-488 interface.
-
Product
Low Noise Op Amplifiers (≤ 10nV/√Hz)
-
Analog Devices’ portfolio of low noise (≤ 10nV/√Hz) op amps includes many amps with the lowest noise performance in the industry. These high speed, low distortion (1 nV or less) op amps enable better signal fidelity in the most demanding conditions, allowing system designers to achieve the lowest total system noise performance in applications with high source impedances. We feature a considerable variety of these amps with wide supply ranges and low power.
-
Product
High Voltage Instrumentation
-
For applications requiring high voltage isolation, Encore Electronics offers a line of DIN rail mounted instruments.
-
Product
PCI & PXI Signal Amplifiers
-
Low power supply rails, a main part of the PXI, cPCI and PCI equipment, are a common cause for an inability to produce high voltage output. Tabor Electronics’ new amplifiers convert the supply rails to higher voltage suitable for signals up to 40Vp-p, thus solving thit problem.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-235-HI
Programmable Resistor Module
The 40-230-235-HI (PXI) and 42-230-235-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 201kΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Oil Breakdown Voltage Tester
DTA IL
-
Insulating oil testing with the BAUR DTA IL. The BAUR DTA Inline is a high performance and reliable oil tester for continuous testing of the breakdown strength of insulating oils during production (inline tests). The combination of extremely short switch-off times during breakdowns and the easy oil sample handling facilitate high quality statements and conclusions on the insulating oil quality.
-
-
Product
LVDT Sensor Amplifiers
-
Analog Devices signal conditioning ICs, together with linear variable differential transformers (LVDTs), can be used to convert mechanical position to a dc voltage. The IC provides both the excitation for the LVDT and the output conversion to dc level with a user selectable gain. ADI LVDT signal conditioners are available to interface with a wide range of LVDTs, including half bridge and standard 4- and 5-wire.
-
Product
Amplifiers
-
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik GmbH offers a large portfolio of high performance broadband RF amplifiers. Optimized for linearity, high dynamic range and low noise, they cover all widely used radio standards like cellular, satellite radio, TETRA/BOS, GNSS, GPS, 802.11, including the new bands for LTE-U. They amplify wideband radio signals from shortwave over UHF, VHF up to 18 GHz in 50 Ohm technology (I-band, G-band, P-band, L-band, S-band, C-band and X-band). They are used as compact RF drivers, antenna pre-amplifiers or RF boosters in a variety of applications ranging from tunnel radio coverage extension, over airspace radio monitoring to in-ear monitoring and can also be offered as 1U 19” rack variants. Due to their advanced design, the power consumption is significant lower than typical industry alternatives, saving cost at customers with respect to cooling.
-
Product
Cross Voltage Testers
-
designed to perform the 60 Hz power line cross test/AC power fault tests required in GR 1089 issue 6 table 4.5 surge test 3,4, 4.3,and 6, and for UL 1950 section 6.4 paragraph 3 and 4.. Preset and Adjustable Time Settings Measuring Terminals including Voltage Sense and Current Shunt portals provide a safe location for users to accurately measure test voltages and output current while setting up tests. Calibration of the Mini_PT-600 is designed to be performed with a simple handheld multi-meter and the removable Currents Shunts can be easily sent to a calibration laboratory if required.
-
-
Product
Solid State Power Amplifier Module (SSPA)
-
Macom Technology Solutions Holdings Inc.
MACOM’s Solid State Power Amplifier (SSPA) and waveguide module product portfolio leverages our world class MMIC technology and system design expertise for high performance Industrial, Aerospace, Defense, and Communications applications. Our SSPA modules feature up to 16 power-combined MMICs in a single module and we can power-combine multiple modules up to 100GHz featuring either coaxial or waveguide interfaces.
-
Product
High Impedance Probes
-
Everbeing offers GGB’s high impedance active probe for failure analysis of your devices. The high impedance with low capacitive design allows measurements of internal nodes without loading the device. For more information, please visit http://www.ggb.com.Everbeing offers GGB’s high impedance active probe for failure analysis of your devices. The high impedance with low capacitive design allows measurements of internal nodes without loading the device. For more information, please visit http://www.ggb.com.
-
-
Product
Panel-mounted Power Amplifier
PAC2000B
-
PA series amplifiers are specially designed for power network real time simulation applications,which requires large power output,high accuracy even at high current output for all kinds of load.
