High Voltage Amplifiers
-
Product
PXI High Voltage Programmable Resistor Module REDEL Connector
40-230-211-HI
Programmable Resistor Module
The 40-230-211-HI (PXI) and 42-230-211-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 62.1Ω with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-153-HI
-
The 40-230-153-HI (PXI) and 42-230-153-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 11.32MΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
40mA One-Channel Amplifiers
-
Piezo amplifiers/controllers are designed for high precision low to mid-speed positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
Product
PXI/PXIe High Voltage Multiplexer, Single 9-Channel, 2-Pole
42-321-124-HI
Multiplexer Module
The 40-321-124-HI (PXI) and 42-321-124-HI (PXIe) are single 9-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
-
Product
Multi - Purpose Digital High Voltage Phasing Meter
Model KM-MPS-50K
-
Kusam Electrical Industries Limited
• AC 50kV and DC 50kV measurement with direct reading.• 4000-count LCD.• Input impedance : 400 Mohm• Auto-ranging : AC : 4.000kV / 40.00kV / 50.0kV, DC : 4.000kV / 40.00kV / 50.0kV• KM 50K must be connected with an approved hot stick (Optional).• Check phases are "in-phase" or "out of phase".• Polarity indication : Positive / Negative• Backlight function.• Auto power off.• Power source : 1.5V(AA) alkaline battery × 2.• Low battery indication(Multi-level).
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-145-HI
-
The 40-230-145-HI (PXI) and 42-230-145-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 2.954MΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
RF Power Amplifiers
-
Specially selected products to complement our ultrasound measurement equipment.
-
Product
Optical Parametric Amplifier
-
AVUS is an Optical Parametric Amplifier (OPA) that provides widely tunable high energy pulses and high repetition rates (up to 1 MHz). AVUS offers highest average output power on the market and is designed for 1 µm fs pump lasers.
-
Product
120 A High Voltage 50 Ω Pulse Generator
TLP-12010C
-
High Power Pulse Instruments GmbH
- High pulse output current up to 120 A (short circuit)- Ultra-fast 50 Ω high voltage pulse output with typical rise time 100 ps (0 A to 40 A) and 300 ps in high-current mode (0 A to 120 A)- Wafer, package and system level TLP, VF-TLP and HMM testing- Up to 180 kW peak output power into 50 Ω load- Built-in HMM pulse up to ±32 kV in 50 Ω-configuration- High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)- 6 USB programmable pulse rise times: 100 ps to 50 ns (custom selectable)- 8 (optional 9) programmable pulse widths: 0.5 ns (optional), 1 ns to 100 ns (0 A to 40 A), 1 built-in pulse width: 100 ns (>40 A)- The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0 A to 40 A)- Optional external pulse width extensions from 5 ns to 500 ns (>40 A to 120 A)using the external pulse width extender TLP-12012A6- Built-in pulse reflection suppression- Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses- Efficient sofware for system control and waveform data management- The sofware can control automatic probers for fast measurements of complete wafers- Combines TLP-12010A and TLP-4010C into one system- Can be operated together with TLP-12012A6 and TLP-3011C pulse width extenders- Integrated interlock safety shut-down- Industrial isolated and EMI/ESD protected USB control interface
-
Product
Distributed Amplifiers
-
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support distributed amplifiers that provide a simple and easy solution for a wide variety of commercial and aerospace & defense applications. MACOM’s distributed amplifier family cover frequencies from DC to 80 GHz and are offered in both bare die and air cavity packages. These devices offer an excellent combination of broadband performance and ease of use for a variety of high-performance applications.
-
Product
Voltage Transformer
PT2
-
SHANGHAI POWOO INDUSTRY CO., LTD
- completely enclosed, good mechanical behavior, suitable for various environments, strong voltage isolation ability, delicate appearance; - the lead wire has a pin format, which makes it easy to be fixed on a PCB; - the mechanical dimensions for this series of PTs are relatively small, hence can be used an electronic component; - good linearity, high precision, wide operating range; - ABS anti-combustion plastic casing; - encapsulated with epoxy resin to ensure strong insulation ability.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-046-HI
-
The 40-230-046-HI (PXI) and 42-230-046-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 5.806MΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Amplifiers
-
Use our optical amplifiers to improve the signal-to-noise ratio (OSNR) and range performance of optical transmission systems.
-
Product
Trip Amplifiers
-
Datexel manufacture a large range of Trip Amplifiers and Process Limit Alarms that accept universal inputs and provide either relays or NPN or PNP transistor outputs. The DAT5028 is also an isolated signal converter and has a local display with up to 4 relays and is DIP switch programmable. The inputs can be Thermocouples, RTD, mV, mA, Resistance, Potentiometers or Voltage. They can be supplied fully configured set up by PC or DIP switches. The DAT5024 is a trip Amplifier / Temperature limit alarm for RTD's, Thermocouples, Voltage, Resistance and Current with the option of 1 or 2 relay outputs hysteresis and delay timers. The DAT5024 E range is an economical choice with DIP Switch programmable for voltage or current input. Either 1 relay or 2 relays (SPDT) are available with delay timers.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-122-HI
-
The 40-230-122-HI (PXI) and 42-230-122-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 1.81kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-016-HI
-
The 40-230-016-HI (PXI) and 42-230-016-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 1.8kΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High Voltage DC Electronic Load
3360F Series（600W~14.4KW）
-
3360F has its own control and display panel, CC/CR/CV/CP/Dynamic modes, 150 sets Store/Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB, RS232,USB and LAN interface.
-
Product
Digital 5KV High Voltage Insulation Tester
Model KM 6305IN
-
Kusam Electrical Industries Limited
• Microprocessor-controlled.• Tests insulation resistance up to 10 TΩ • 4 Insulation test voltages: 500V, 1000V, 2500V, 5000V.• AC / DC Voltmeter.• Short-circuit current up to 5mA• PI (Polarization Index) indication.• DAR (Dielectric Absorption Ratio) indication.• Auto-ranging on all insulation ranges.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-314-HI
-
The 40-230-314-HI (PXI) and 42-230-314-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 470Ω with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-246-HI
Programmable Resistor Module
The 40-230-246-HI (PXI) and 42-230-246-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 5.806MΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Analog Summing Amplifier
SIM980
-
Stanford Research Systems, Inc.
The SIM980 Summing Amplifier has four input channels that can be added or subtracted from each other. The output noise is less than 60 nV/√Hz, and crosstalk between channels is less than -80 dB. With a bandwidth of 1 MHz, a slew rate of 40 V/ms, and input offsets that are trimmed to ±100 µV, the SIM980 is extremely useful in many analog applications.
-
Product
RF POWER AMPLIFIERS
BSA Series
-
RF Input:N-f, standard on rear panelRF Output:standard on rear panel<1 kWN-f<3 kW7-16-f<5 kWEIA 1 5/8Mains Supply:Line Power:<1000 VA100 ... 240 V AC ±10% / 47 ... 63 Hz1000 ... 3000 VA200 ... 240 V AC ±10% / 47 ... 63 Hz>3000 VA3x 400 V AC ±10% / 47 ... 63 HzElapsed Time Meter:via status displayAmbient Temperature:0 ... +45 °CStorage Temperature:-20 ... +85 °CRelative Humidity:up to 95% (non-condensing)Operating Altitude:up to 2000 m above sea levelVibration and Shock:MIL-STD-810 GCooling:forced air with integral blowerair intake from front, air exhaust at rear
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-010-HI
-
The 40-230-010-HI (PXI) and 42-230-010-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
VOLTAGE TRANSFORMERS
-
Designing & manufacturing a range of high quality, voltage transformers in three different frame sizes for both measuring and protection duties. Transformers which are designed to comply with the requirements of IEC 61869-3 or other international standards as required can be supplied to satisfy most Low Voltage applications.
-
Product
High Voltage Power Supplies
-
High voltage SCR controlled power supplies require the following:Output voltage is high. Output current is generally Low.Voltmeter and ammeter display the output voltage and current under load.Potentiometers are used to adjust output voltage and limit output current from minimum to maximum.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-251-HI
-
The 40-230-251-HI (PXI) and 42-230-251-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 2.95MΩ with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Power Multiplexer, Single 24:1
40-331A-001
Multiplexer Module
The 40-331A-001 single 24:1 MUX is part of our range of 40-331A/332 High Voltage Power Multiplexer and Matrix Modules and is suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching.
-
Product
High Voltage Probe
HVP-39pro
-
* 39KVDC+ACpeak* 900MΩ Impedance* DC~50MHz(-3dB)* 1000:1 for Oscilloscope* Very Low Nosie
