VxWorks
-
Product
TTESync For VxWorks 653
-
TTESync is a synchronization component that allows tight synchronization of VxWorks 653 partitions to the fault-tolerant system-wide cycle time of the TTEthernet communication network. All partitions executed on different modules can be “pinned down” within the overall system cycle time, thus enabling the lowest latency and minimum jitter in message exchange among distributed functions. At system level this results in clean layering, well-understood functional interactions and simpler application design, testing and system integration. System architects can reduce system complexity and further optimize system size, weight, power (SWaP) and life-cycle costs.
-
Product
TTEDevelopment System A664 For VxWorks 653
-
The TTEDevelopment System A664 supporting the ARINC 653 interface is an out-of-the box starter kit for integrating TTEthernet’s deterministic network technology with the time and space partitioned real-time operating system VxWorks 653. The easy-to-use and ready-to-run solution includes hardware and software as well as a Distributed IMA demo application showing deterministic communication among the different real-time operation system partitions. The system supports up to 1 Gbit/s speed, enables event-driven Ethernet (IEEE 802.3) as well as rate-constrained (ARINC 664 part 7) and hard real-time (Time-Triggered Ethernet SAE AS6802) communication on the same network with the option to synchronize IMA modules using the fault-tolerant TTEthernet network time base.
-
Product
VxWorks
-
The latest release of VxWorks includes support for OCI containers. Now you can use traditional IT-like technologies to develop and deploy intelligent edge software better and faster, without compromising the determinism and performance. Find out why independent researcher VDC has once again named VxWorks the #1 RTOS for the edge.
-
Product
Shared Memory Network XMC Interface
XMC-SMN
-
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PC104p-429
-
*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
ARINC 429 Test & Simulation Interface for VME
VME-429
-
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
ARINC 429 Test And Simulation PMC Module
PMC-429
PMC Module
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
ARINC 429 Test And Simulation PCI Module
PCI-C429
-
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
3U VPX Single Board Computer
VP32002
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP32002 is a high-performance 3U VPX single-board computer, compatible with PC architecture, especially it is a China Local-design, Local-assembling product. VP32002 is an all-in-one design, supporting the 3rd generation of Intel core processors and QM77 chipset; also supports up to 16 GB onboard DDR3 memory and up to 32GB Disk-On-Modules, these features ensure its stable operation in strong shock and vibration environments. VP32002 supports a XMC interface and various I/O interface such as two SATA600 channels, two Base-BX/T GbE, two UARTs and two USB interface.The board provides a flexible PCI-Express bus interface to the backplane. The interface can be configured as follows: 1 Port x8 PCIe, 2 Ports x4 PCIe, 4 Ports x2 PCIe. This feature makes it suitable for either distributed switching system or centralized switching system.For the user to quickly form application solutions, LinkedHope provide VP32002 a complete driver package including Windows, VxWorks, Linux and QNX.
-
Product
6U Processor Board
CP62102
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62102, a product designed by LinkedHopeTM, is a 6U CPCI processor board based on Intel QM77/HM76 platforms supporting 3rd generation Intel i series CPU, up to 2.7GHz frequency, HD4000 integrated core graphics and dual-channel SO-DIMM memory (1333/1600) with up to 16GB DDR3 ECC (optional) and up to 64GB on-board SSD storage.CP62102 provides VGA and HDMI display and supports different display terminal output. CRT displays up to 2048x 1536. Besides CP62102 provides a wealth of software drivers (BSP) support, including Windows7, Windows Vista, Windows XP, WES 7, VxWorks, Linux, etc., as can reduce system integration workloads and end application development efforts, so to shorten time to market.
-
Product
ARINC 429 Test And Simulation PXI Module
PXI-C429
-
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Extreme Rugged PCI-104 Single Board Computer with Intel® Atom™ Processor E3800 Series SOC
CM3-BT1
Single Board Computer
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
Product
ARINC 429 PMC Interface Module
PMC-429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx ChannelsProgrammable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application Interface supporting C++, C#, and .net DevelopmentDevice Driver Support: Windows, Linux, VxWorks, and other operating system - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
MIL-STD-1553 XMC Interface Module
XMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurations - Transformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating availableDesigned for extended temperature operations - x1 Lane PCI Express Host Interface - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Commercial and Open Source Implementation of the Object Management Group Data Distribution Standard
Vortex OpenSplice
-
Vortex OpenSplice enables data to be shared and integrated across a wide spectrum of operating systems and platforms. It provides a full implementation of both the OMG DDS latest rev1.4 (DCPS profiles) and the OMG-DDSI / RTPS v2.3 interoperable wire-protocol standards. It is targeted for use with server-class (desktops, racks etc.) platforms as well as more specialized real-time embedded environments and operating systems (e.g. single board computer running VxWorks). Vortex Opensplice is fully interoperable with Cyclone DDS, Vortex Link and and Vortex Insight .
-
Product
Extreme Rugged PC/104-Plus, PCI-104 Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM3-BT4
Single Board Computer
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
Product
Software Development Kit for ARINC 664 Applications
ARINC 664 SDK
-
Avionics Interface Technologies
Software Drivers for Windows, Linux, VxWorks, and other Operating Systems (on request) - Compatible with all AIT ARINC 664 Interface Modules - Includes documented APIs with source code examples for C/C++ - Integrates with AIT’s Flight Simulyzer software (share XML bus configurations between API’s and Flight Simulyzer) - Support provided by AITs industry leading applications engineering team
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Dual Port Simulator Fiber Channel XMC Module
XMC-FC4 Simulyzer
Simulator
*Two independent fiber channel ports*The two SFPs accept electrical as well as optical transceivers*Each port supports 1, 2, or 4 Gbps*Supports customer-specific defined transmission speed*Comprehensive decoding of FC-1, FC-2 and Upper Layer Protocol (ULP) frames*Triggering and filtering*Supports DMA for high-speed streaming*IRIG-B time code encoder / decoder for data correlation*Supports ULPs such as FC-AE-ASM, FC-AE-RDMA, FC-AE-1553 and FC-AV*Supports HS-1760E applications such as AS5653, AS5652 and AS5627*Optional fcXplorer, Windows-based FC simulation and analysis test software*FC SDK (Software Development Kit) provides drivers and APIs for Windows XP / 7,*Linux, VxWorks, QNX Neutrino RTOS and others on request
-
Product
HS-1760 Flight Rated XMC Network Interface Controller
XMC-1760-NIC-CC
-
Avionics Interface Technologies
Dual Channel configurations supporting NC/NC, NC/NT, or NT/NT - 75 Ohm single ended copper or 150 Ohm differential - Eight (8) opto-isolated discrete I/O lines - Rear I/O through the P16 connector - Conduction-cooling and/or conformal coating available - x4 PCIe interface to NIC interfaces, with DMA controller for data movement - Designed for extended temperature operations - ANSI Application interface supporting C development - Device driver support: Windows, Linux, & VxWorks (others on request)
-
Product
Interface
P-SER
Interface
P-SER I/O product is a native PMC form factor interface providing real-time serial input and output with high time-precision reception/input time-stamping, scheduled transmission/output, event triggering and interrupt support. This interface is designed to meet the needs of both the simulations/test and the real-time embedded applications whether in Windows or VxWorks environments.
-
Product
AFDX ® / ARINC 664 Test Cards
-
Our AFDX ® / ARINC664 test cards can be used for test and simulation applications in which it is necessary to send and receive data via the AFDX® data bus. They support the 10/100 Mbit / s ARINC 664 Part 7 Ethernet interface as well as the next generation 1 Gbit / s Ethernet. / ARINC 664 test cards are delivered with device drivers, high-level interfaces (APIs) for Windows Linux, VXWorks and LabVIEW / LabVIEW Real-Time (further on request).
-
Product
Shared Memory Network PCI & PCIx Interface
PCI-SMN
-
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Compatible with PCI & PCIx Host System Slots - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
Product
6U CPCI Processor Board
CP62101
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62101, a product designed by LinkedHopeTM, is a 6U CPCI processor board based on Intel QM67/HM65 platforms supporting 2nd generation Intel i series CPU, up to 2.5GHz frequency, HD3000/2000 integrated core graphics and dual-channel SO-DIMM memory (800 /1066 /1333) with up to 16GB DDR3 ECC (optional) and up to 64GB on-board SSD storage.CP62101 provides VGA and HDMI display and supports different display terminal output. CRT displays up to 2048 × 1536. Besides, CP62101 provides a wealth of software drivers (BSP) support, including Windows7, Windows Vista, Windows XP, WES 7, VxWorks, Linux, etc., as can reduce system integration workloads and end application development efforts, so to shorten time to market.
-
Product
COM Express Compact Size Type 6 Module with Intel Pentium, Celeron N3000 Series and Atom x5 E8000 SoC (formerly codename: Braswell)
cExpress-BW
Computer on Module
ADLINK cExpress-BW provides two DDI channels (with up to 4K resolution) and one eDP or DDI3 channel supporting three independent displays, enabling it to drive multiple HD screens without the need for a discrete graphics card. In addition, LVDS is optionally available to support next generation displays. The cExpress-BW offers up to five PCI Express lanes x1. A wide range of operating systems are supported, including Linux, Windows 7 and 8.1u, Windows Embedded Standard 7, Windows Embedded Industry 8.1 and VxWorks.
-
Product
Application Programming Interface Software
AltaAPI
Interface
Alta’s 1553 and ARINC cards include the most advanced Application Programming Interface (API) library tools in the avionics industry, AltaAPI. The API architecture is a properly OSI modeled development package that provides an extremely flexible design to provide quick porting to various operating systems (such as VxWorks 5.X/6.X/7/MILS, Integrity, LynxOS RTOS), Linux 32- and 64-bit, Solaris 10, LabVIEW and 32- and 64-bit Windows 7/8/8.1/10.
-
Product
Embedded Services
-
Firmware Development (Boot/HAL/BSP), Device Driver Development (USB/PCIe/SATA), Diagnostic software Development, Application software Development, Algorithm Development, OS: RTOS, Linux, Android, VxWorks, Kernel Porting, Optimization, debugging and Benchmarking, Processors: ARM, 8051, ARC, Languages: Assembly, C, C++, Java, Scripting: Perl, Python, C Shell Scripting
-
Product
HS1760/MIL-STD-1760E Network Interface Controller for PCI Express
PCIe-1760-NIC-FP
-
Avionics Interface Technologies
Configuration Variants available: PCIe-HS1760-NCNT: One NC Node and One NT Node, PCIe-HS1760-NCNC: Two NC Nodes, PCIe-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data - 75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
Product
3U Processor Board
CP39104
-
LinkedHope Intelligent Technologies Co.,Ltd.
Designed for industrial communication, CP39104 is a 3U CPCI serial card compliant with PICMG 2.0 R3.0 specification.CP39104 applies XR17D154 serial communication controller of EXER, and supports 4x RS232/RS422/ RS485. Therefore, CP39104 is highly suitable for testing and measuring in serial data communication applications.LinkedHope® provides CP39104 with a wealth of software drivers and BSP, including VxWorks, Linux, Windows, etc., to enable a wide range of application scenarios.
-
Product
Shared Memory Network PCI Express Interface
PCIe-SMN
-
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodesNetwork interrupts supported - PCIe 2.0 (x4) CompliantSoftware Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
