Protection Relay Test
-
Product
Built-In Relay Self-Test Diagnostic Test Tool
BIRST
-
Verification and diagnosis of complex switching operation in a test system has always been an issue. BIRST (Built-In-Relay-Self-Test) diagnostic test tool provides a quick and simple way of finding relay failures available on some of our LXI and PXI switch matrices.
-
Product
Test SIP
-
VoIP, Video, and IPTV products must withstand and continue to function when facing all the conditions that occur on the Internet. These include attacks from hackers exploiting vulnerabilities in security and protocols as well as the common phenomenon of congestion, delay, jitter, drops, and so on. VoIP, Video, and IPTV products must demonstrate robustness and resiliency in the face of unusual and/or illegal conditions.
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 25xDPST
42-146A-002
-
The 40-146A-002 (PXI) and 42-146A-002 (PXIe) 25xDPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
Protection And Control For Electric Vehicle
-
Solutions designed specifically to protect electric vehicle charging systems. Wide range of protection, including Type A + 6 mA DC or type B devices, with or without automatic reclosing, in compliance with the applicable laws.
-
Product
Conformance Tests
-
According to german Duden conformance means ‘in agreement, accordant’ (from Late Latin conformitas – similarity). Any check on compliance of a test object with its specification can therefore be regarded as a conformance test. A conformance test has become established in the field of networked systems.
-
Product
Overdrive Protected Amplifier
-
RF Lambda’s line of overdrive protected amplifiers incorporate a technology which eliminates the need for a limiter to protect the amplifier from damage. High input powers up to 10W can be injected in the amp without damage. Hermetically sealed options are available upon request.
-
Product
Loudspeaker Testing
TTC
-
The weakest link in your measurement chain is your chamber, the new TTC chambers solve these problems...*Anechoic chambers have massive footprints:The TTC gives you equal or better results with a compact footprint*Achieving repeatable measurements is difficult in an anechoic chamber:The TTC guarantees the microphone and loudspeaker positions*Anechoic chamber accuracy suffers at low frequencies:The TTC is capable of measuring below 20 Hz*Results are not transferable between most test chambers:The TTC meets international standards IEC 60268-21:2018 & IEC 60268-22:2020*Most chambers are difficult to calibrate and awkward to use:The TTC is calibrated and is ready to interface to your microphone and analyzer
-
Product
Test System
Tessy
-
TESSY automates the whole unit test cycle including regression testing for your embedded software in C/C++ on different target systems. As an easy-to-install and easy to operate testing tool TESSY guides you through the unit test workflow from the project setup through the test design and execution to the result analysis and reporting. TESSY takes additionally care of the complete test organization as well as the test management, including requirements, coverage measurement, and traceability.
-
Product
Isolated Relay I/O Card
mPCIe-IIRO-8
-
The mPCIe-IIRO-8 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Product
Test Automation
-
Test automation can be the solution to releasing new features and functionality with reduced time to market and uncompromising quality. There will, however, always be times when manual testing is the most appropriate approach.
-
Product
Test System
DA-1 ATS
-
The DA-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
Product
SuperHeater Overheat Protection
SHOP
-
The SuperHeater Overheat Protection (SHOP) system is a proprietary technology that helps mitigate the risk of superheater tube failure due to short-term overheat during boiler start-ups. SHOP assists operators in the management of boiler start-ups by enabling the detection of superheater tube clear events (TCE’s).
-
Product
Test Accessories
-
For in-house designed ATE systemsFor any customer’s existing systemProviding complete electrically- and mechanically-designed units from the customer’s own specificationsUtilize our build-to-print services to duplicate your existing design
-
Product
Test Sets For Diagnostic Testing
-
Test Sets For Diagnostic Testing are designed to test Oil Resistivity, Tan Delta, High Voltage Surge Comparison, etc. These test sets are automated instruments used to measure electrical features to insulate transformer oil, liquids and varied other insulating materials. They are ideal for revealing different localized problems and varied weak spots in the insulation. These modern testing sets are designed to provide high accuracy in results. In addition to this, they are easy to maintain testing sets available to ensure accurate readings.
-
Product
Test Receiver
NTR GNSS
-
Our primary objective is to provide a high performance and fully flexible test receiver for all types of GNSS systems. Thus, the NTR fully supports all existing navigation systems. The signal processing is fully flexible. The high performance correlation engine with up to 80 channels is implemented in a powerful set of FPGAs. Signal acquisition and tracking are realized on a high performance embedded ARM Cortex A8.Supporting up to 4 L-band frequencies in parallel, the NTR GNSS test receiver supports all current GNSS transmission frequencies. Due to its plug-in design, the RF front-end can easily be customized for special filtering and other frequencies.
-
-
Product
Safety Relay
-
Leuze electronic GmbH + Co. KG
With the MSI safety relays, individual safety sensors can be integrated quickly and easily into the safety circuit of machines and systems. The MSI contact extensions are used both as an output extension for OSSDs and for contact multiplication for evaluation units and safety controls.
-
Product
In-circuit Test
Medalist i1000 Systems
-
Cover Extend Technology (CET) is now supported on the Medalist i1000D. The i1000D only requires a VTEP MUX card to enable CET. If you are already using test fixtures with VTEP MUX cards , you can now implement CET without any fixture modification. Simply add new VTEP probes to devices that were previously not testable. This greatly reduces implementation efforts.
-
Product
ITA, i1, EMI Shielded, With Protective Cover
410128102
-
The i1 EMI has many of the standard features of the i1, in addition to Electro-Magnetic Interference (EMI) protection. The EMI shielding effect on the i1 EMI ITA is provided by the stainless steel fibers in the removable plastic cover and threaded metal coupling adapter.
-
Product
Safety Testing
-
Whitelegg has over 80 years of experience in the design manufacture of market-leading electrical safety test equipment. Our unrivalled range of electrical test equipment serves a wide variety of safety testing and precision measurement applications for use in a variety of industries including manufacturing, construction, education, utilities, aerospace, calibration and anywhere else where there is a requirement for electrical safety testing or precision resistance measurement.Test equipment is cost effective, helps you to minimise expense, improve efficiency and increase profit. Whether you need electrical test equipment, environmental test, power analysers or HV Test Equipment, we stock the products to meet your demands, all backed by our first-class technical support if you have any problems using the equipment.
-
Product
Microwave Testing
40A
-
The GGB Industries, Inc., MODEL 40A microwave probe sets new standards in microwave probing performance. Using low loss coaxial techniques, the Model 40A achieves an insertion loss of less than 0.8 db and a return loss of greater than 18 db through 40 GHz.
-
Product
Memory Testing
-
C.C.P. Contact Probes Co., LTD.
Standard and Custom test solutions for RAM, Flash and many other memory chips.
-
Product
Digital Relay Test Kit
PW636i-F
-
PW636i-F (6×32A, 4×300V, 8 fiber optic ports) is the new generation of PW series relay test set which can be used both as an conventional relay test kit and IEC61850 testing tools.
-
Product
Adaptive Relay, Virtex-6 FPGA - 3U VPX
Model 52624
-
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Single-In-Line Reed Relays
Series 106
-
SIL relays - 0.2 inch wide packages. Requires a board area of 0.2 x 0.8 inches (5.1mm x 20.3mm)
-
Product
Packaging Test
-
Underwriters Laboratories Inc.
UL offers ISTA packaging tests to assess the security of goods during transport, so retailers and manufacturers can feel confident that packaging is up to the job, thus reducing product loss and customer complaints.
-
Product
Test Adapter
RAMCHECK® SIMM
-
The RAMCHECK SIMM Adapter is another addition to the RAMCHECK memory tester. It provides a needed solution for testing older 72-pin EDO/FPM DRAM SIMM modules. An optional adapter for 30 and 72-pin SIMMs is also available
-
Product
Relays
-
Mitsubishi Electric Automation, Inc
Mitsubishi Electric offers AC and DC controlled Contactor Relays with multiple open and closed contacts configurations that can be used in a variety of applications; alarms and sensors, signal switching, detecting and controlling faults that occur in electrical circuits.
-
Product
Attribute Testing
-
Critical attribute testing during manual or automated processing is essential to any manufacturing success. Tech Group has developed many testing solutions both standard and custom-made for mainly electronics and mechanical industry. Our modular designs give the advantage to offer short lead-time, cost efficient solutions according to your exact needs.
-
Product
Safety Testing
-
Seaward's high quality electrical safety testing equipment has a worldwide reputation for technical excellence in the appliance, electrical and electronics manufacturing sectors.
