Showing results: 256 - 270 of 271 items found.
-
Model 200 -
OAI
The OAI Model 200 Mask Aligner is a cost-effective high performance mask Aligner that has been engineered with industry proven components that have made OAI a leader in the photolithography capital equipment industry. The Model 200 is a tableop mask Aligner that requires minimal cleanroom space. It offers an economic alternative for R&D, or limited scale, pilot production. Utilizing an innovative, air bearing / vacuum chuck leveling system, the substrate is leveled quickly and gently, for parallel photo mask alignment and uniform contact across the wafer during contact exposure. The system is capable of one micron resolution and alignment precision.
-
ENVIROMUX-EWDS -
Network Technologies Inc
Balanced wind direction vane with a near-zero friction bearing and a high accuracy magnetic angle sensor to provide precision wind direction. Sensor range: full 360 degrees , zero deadband. Accuracy: ±1.8 degrees. Resolution: 12 bit or 0.025 degrees. Directional Vane approximately 8 inches (203 millimeters). 3 wire flying leads, 25-feet (7.6-meter). Supply voltage: 4.5 to 5.5 VDC. Current: 15 mA typical. Output: 5 to 95% of input voltage (0.25 to 4.75VDC). Requires the ENVIROMUX-S5VDC-5V to operate with ENVIROMUX-2D/5D/16D. Maximum cable length: 1000 ft (305m)
-
Extech EN510 -
Extech Instruments Corporation
Convenient 10-in-1 Environmental Meter measuring Air Velocity, Air Flow, Air Temperature, Type K Temperature, Heat Index, Humidity, Wet Bulb, Dew Point, Windchill, and Light Level. Includes built-in low friction ball bearing mini vane wheel, a precision photo diode with cosine and color correction filter, and a capacitive humidity sensor for high accuracy. The Type K input accepts standard Type K Thermocouple probes to measure surface temperature up to 2372°F (1300°C). Features large dual LCD with backlighting, Data Hold, and Min/Max function.
-
Model 200IR -
OAI
The OAI Model 200IR Mask Aligner is a tabletop system that requires minimal clean room space. It is a cost-effective alternative for R&D or limited scale, pilot production. Utilizing an innovative, air bearing / vacuum chuck leveling system, the substrate is leveled quickly and gently, for parallel photo mask alignment and uniform contact across the wafer during contact exposure. The Model 200IR Mask Aligner is capable of one micron resolution and alignment precision. It has an alignment module which features mask insert sets and quick-change wafer chucks that enable the use of a variety of substrates and masks without requiring tools for reconfiguration. The alignment module incorporates micrometers for X, Y, and z-axis.
-
YQA Series -
Jinan Testing Equipment IE Corporation
This kind of machine is designed according to the International standards EN 10263-1:2001 “Metallic materials upset test methods”, especially for the quality inspection of high-speed rods and wires. Through simulating the quick press conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. This kind of machine is widely used in the steel industry, standard samples manufacturing industry, and tools manufacturing industry, for the inspection of the metallic materials upset tests. Under the room temperature or the hot conditions, exert test force on the direction of specimen axial line, quickly compress the specimen, and then inspect the metal ability of bearing upset deformation in the specified upset ratio. It also can show the metal surface disfigurements.
-
MD-250-M -
Mustang Dynamometer
Mustang has developed a low-cost, simple to use, easy-to-install heavy duty chassis dynamometer that can be used to simulate real-world driving conditions in a safe, controlled environment and can also be used for “static” diesel smog testing for regulatory purposes. This model is used in Diesel Smog Programs in Nevada and Colorado when combined with an approved opacity meter. The MD-250-M is a compact dynamometer with industry proven design features including 10.7-inch rollers, heavy duty spherical pillow-block ball bearings, welded structural steel frame, 7.5 hp calibration motor, and an industry standard air-cooled, Eddy Current Power Absorption Unit (PAU) for road-load simulation. The MD-250-M is available in both right and left hand configurations to accommodate different facility designs.
-
YQ/YQR Series -
Jinan Testing Equipment IE Corporation
The series of upset testing machine are designed according to the International Standard 'Metallic Materials Upset Test Methods', especially for the quality inspection of high-speed rods and wires. Through simulating the quick impact conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. Under room temperature or hot conditions, exert test force in the direction of specimen axial line, quickly compress the specimen, and then the machine can inspect the metal ability of bearing upset deformation in the specified upset ratio. The upset testing machine can also show the metal’s surface disfigurements. The upset testing machine is widely used in the steel industry, standard specimen manufacturing industry, and tools manufactures for inspecting the upset tests of metallic materials.
-
Extech SDL310 -
Extech Instruments Corporation
The SDL310 records data on an SD card in Excel format. Measures Air Temperature to 122°F (50°C) and air velocity to 4930ft/min. Stores 99 readings manually and 20M readings via 2G SD card. Stores 99 readings manually and 20M readings via 2G SD card. Type K/J Thermocouple input for high temperature measurements. Large (9999 count) LCD displays Air Velocity and Temperature simultaneously. 2% velocity accuracy via low friction ball bearing vane wheel on 39 in. (1m) cable. Record/Recall Min, Max, Data Hold and Auto power off. Adjustable data sampling rate. Complete with 6 x AA batteries, SD card, vane sensor with 3.9ft (120cm) cable, and hard carrying case.
-
V-522 • V-524 • V-528 -
Physik Instrumente GmbH & Co. KG
Reference-class linear stage. Linear positioning stages with magnetic direct drives largely dispense with mechanical components in the drivetrain and the drive force acts directly on the motion platform. Together with precision bearings, a high travel accuracy and longer lifetime is achieved. The linear positioning stages are particularly suitable for scanning applications. PIMag® Voice Coil. Voice coil drives consist of 2 essential components: A permanent magnet and a coil, which is located in the air gap of the magnetic field. When current flows through the coil, it moves in the magnetic field of the permanent magnet. The direction of motion depends on the polarity. Thanks to their low weight and friction-free drive principle, voice coil drives are particularly suitable for applications, which require high dynamics and high velocities at limited travel ranges. High scan frequencies and precision positioning are also possible with these drives, because they are free of the effects of hysteresis.
-
Extech SDL300 -
Extech Instruments Corporation
The SDL300 records data on an SD card in Excel format. Metal Vane withstands temperatures to 158°F (70°C) and air velocity to 6900ft/min. Datalogger date/time stamps and stores readings on an SD card in Excel format for easy transfer to a PC. Adjustable data sampling rate from 1 to 3600 seconds. Stores 99 readings manually and 20M readings via 2G SD card. Type K/J Thermocouple input for high temperature measurements. Large (9999 count) LCD displays Air Velocity and Temperature simultaneously. 2% velocity accuracy via low friction ball bearing vane wheel on 39" (1m) cable. Record/Recall MIN, MAX, Data Hold, Auto Power Off. Complete with 6 x AA batteries, SD card, metal vane sensor with 3.9ft (120cm) cable, and hard carrying case.
-
Type HFDF -
National RF, Inc
National RF’s Type HFDF high frequency location system is a proven noise hunting and location directional antenna system that allows you, in many cases, to walk right up to the source of High Frequency (HF) noise! Used by several power companies around the United States, professional noise hunters, and other communications specialists, the HFDF has located noise sources that emanated from pole power transformers, arcing electric fences, CATV in-line amplifiers, plasma TV screens, and even Marijuana grower’s heating lamps! The system incorporates several plug-in, tunable magnetic loop sensors of a proprietary National RF design, that cover the frequency range between 1.8 MHz and 55 MHz. The unit is packaged in a hand-held, lightweight metallic enclosure, with a pistol grip and a magnetic compass mounted on top. The compass is used to get magnetic bearings to the noise source, which may be plotted on a map to triangulate, and ultimately pin-point, the location of the noise source. In certain cases, our customers tell us that they have been able to walk right up to the interfering noise source and correct the situation on the spot!
-
MOTOMEA
*Uses Hysteresis brake for measurement devicesIn addition to minimizing the magnetic field aperture in which the hysteresis cup rotates, this component minimizes the cup’s moment of inertia, enabling improved torque-control precision and controlling vibrations at high RPMs.*Enables stable measurements from low through high RPMsTorque is detected by the force exerted by the brake stator, enabling stable torque measurements from low through high RPM rages. This component features a maximum speed of 30,000 rpm (depending on torque rating). In addition, optional components can be used to improve speed resolution for use with low-speed motors of 100 rpm or less.*Compatible with broad range of torque ratings from 5mN*m through 50 N*mMeasurements components can be selected to suit motor power to ensure high-precision measurements. Users can select from 14 models of TA/TB torque measurement components, offering differing torque ratings.*Long-lasting non-contact brake Hysteresis brakes are non-contact devices and offer long service life. Except for bearings, hysteresis brakes have virtually no maintenance requirements.*Superior heat resistanceAnother hysteresis brake advantage is its resistance to changes in torque values due to increases in brake temperature or surrounding temperature.
-
HT6561 -
Rinch Industrial Co.,Limited
Product synopsis1.1 Typical Applications* Die cavity of molds* Inspection of bearing and other mass produced parts on aproduction line* Failure analysis of pressure vessel, steam generator andother equipment* Inspection of installed machinery, permanent parts ofassembled systems and heavy work pieces.* Testing surface of a small hollow space* Material identification in the warehouse of metallic materials* Rapid testing in large range and multi-measuring areas forlarge-scale work piece1.2 Testing Features* Palm size for narrow space.* Test at any angle, even upside down.* Direct display of hardness scales HRB, HRC, HV, HB, HS,HL.* Large memory could store 250 groups including singlemeasured value, impact direction, material and hardnessscale etc.* User recalibration function allowed.* Can communicate with PC computer for statistics andprinting by the optional cable.* Manual or automatic shut down.* Low battery indication.1.3 Technical SpecificationsDisplay: 12.5mm LCD with back lightAccuracy: Display error ±0.8% at LD=900Measuring range: 200-900LConversion: HL-HRC-HRB-HB-HV-HSDMaterials: 9 different common materialsWith RS232C interfaceMemory: 250 data can be stored and re-readableImpact device: D Will handle the majority of hardness testingapplications. Weight: 75gPower supply: 2x1.5V AAA size batteryDimension: 146×65×36mmWeight: 130g (not including batteries)Working temperature： - 10℃～＋50℃Storage temperature：- 30℃～＋
-
VF-121 -
National RF, Inc
The Vector-Finder Types VF-121 and VF 121A are unique in the Vector-finder series of direction finding antennas. They incorporate a proven design, electro statically shielded loop sensing element with modern solid state low noise analog and digital technology to allow detection and location of aircraft band signals. Both the VF-121 and the VF 121A incorporate a unique digital modulator which allows the user to more easily home-in on unmodulated carriers. Such cases occur at airports when transmitter may be accidentally keyed on during aircraft overnight layovers. The VF-121 is specifically designed to be used on airport premises where signal strengths are high. To compensate for very strong signals, an integral attenuator is also incorporated to allow the user to operate the unit close-in to aircraft. The VF-121A differs in that a high gain, low-noise preamplifier is utilized with the sensing element in order to hunt signals that may be weak or at a distance. The unit is ideally suited for the location of ELT transmitters in the field. Both units are tunable over the 118 MHz to 130 MHz aircraft frequencies and interface directly to the user’s aircraft band receiver or transceiver via the antenna jack. With the antenna system connected to the receiver, the user will hear the desired signal. If the signal is unmodulated, the digital modulator will generate a tone on the carrier. When the handheld unit is rotated about, an audible null on the received signal or the generated tone will be heard. This null aligns with the axis of the equipment case and represents the direction of the received signal. This direction may be read from the black dial compass mounted on the top of the enclosure. As the response is bi-directional, triangulation may be used to determine the true bearing when the true direction is not known.
-
Adamant Namiki Precision Jewel Co Ltd.
Zirconia ferrule sleeve is an important part in optical fiber communication and is the basic product of our optical communication parts. We have developed an optical communication parts part of hasad developed based on grinding and bearings. Offer Optimum Performance And Quality For Each Type Of Optical Fiber, Optical Connector And Optical Device. We Also Offer Pin Gauges And Ring Gauges For Measuring Precise Dimensions Indispensable To Our Quality Assurance . These Gauges Have Little Wear, Good Compatibility With Ferrules And Sleeves, Zirconia , sapphire and cemented carbide are used as materials.Various Optical Connectors And Adapters Using Ferrules And Sleeves, Follow The Long History FC And SC Connectors, MU , LC Connectors Are Also Available. In Particular, LC Connectors Are Deployed In A Wide Lineup With Adapters. In The Field Of Optical Devices, We Provide Codes Master , Various Patch Cords , Conversion Adapters That Connect Different Types Of Connectors, Attenuators And Terminators That Provide Stable Characteristics, Which Are Manufactured Using The Ferrule Quality Of Our Own Manufactured Parts We Will. We Also Offer Parts For Optical Devices SuchAs Fiber Array Used For Connection Of PLC, AWG And Others. In The Field Of Optical Modules, SC And LC Receptacles , Fiber Stub, Pigtail Fiber And Other Optical Module Parts, And Now We Have Provided TOSA, ROSA And Other Optical Module Manufacturing Consignment Services. We Also Deal With Various Lensed Fibers Which Processed Fiber Tip With High Precision . In Addition, We Also Flexibly Deal With Precision Component Processing Used In Optical Communication Field, Special Specification Ferrule, Sleeve Etc. Please Contact Us.
