DDR Test
-
Product
Amplifier, Switch and Test Box
CLIOQC Model V
-
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
Product
Bypass Diode Thermal Test System
-
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
Product
Testing Equipment for UN38.3 & UL
-
We provide complete lab equipment solutions for UN38.3 testing and you are welcomed to visit our lab located in Richmond, CA -- please contact us for an appointment. On-site training available with extra cost.
-
Product
EMI/EMC Testing
-
This type of testing is required for devices, systems, and applications within the military and aerospace industries. Weapons, aircraft, ground and support equipment, electrical, and electronic systems must meet the established requirements.During electromagnetic interference the component's electrical circuit is affected due to either electromagnetic conduction or electromagnetic radiation from an external source.
-
Product
FCC Testing & Certification
-
F2 Labs can provide you with Federal Communications Commission (FCC) Certification in our EMC Testing Lab, Supplier’s Declaration of Conformity (SDoC), formerly Verification and Declaration of Conformity, testing. Manufacturers who sell electrical and/or digital products in the United States must have their products tested by an accredited lab certified by the FCC. F2 Labs is accredited by the FCC as a Conformity Assessment Body (CAB). We partner with a Telecommunication Certification Body (TCB) in order to provide our clients with FCC Part 15 certification and compliance testing & approvals.
-
Product
Multifunction Substation Test Set
STS 5000
-
STS 5000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
Product
Wireless Router Test Platform
-
Promptlink Communications, Inc.
Promptlink's Wireless Router Test Platform (WRTP) is a complete functional router testing solution designed for the highest volume testing requirements. WRTP is the ultimate tool for accurate, high-demand testing of wireless routers. With added support for TR069 through Promptlink's own ACS, WRTP is the solution that gives you the ultimate power and productivity to keep your business moving forward.
-
Product
Interconnect Test Leads
142-1
-
This 64 inch pair of test leads connects with many different testing accessories and probes. Especially those found in typical test lead kits and assortments. The ends terminate in universal size 4mm banana plugs.
-
Product
Medium-size Compact Antenna Test Range
H-Series CATR
-
The H-Series CATR chamber provide complete 3D performance assessment for 5G OTA devices and antennas including gain, efficiency, directivity, polarization and beam characteristics for frequencies from 3 up to 110 GHz, capable of supporting forthcoming 5G Sub-6 GHz (from 3 to 6 GHz) and mmWave (24 to 110 GHz) standardized testing including TRP/TIS, EIRP, EIS, IBB and emissions in accordance to 3GPP TR38.810 and TR37.842.
-
Product
Power mixed test system
-
Power device or module with which are digitally controlled and memory can be measured per system.
-
Product
Pump, Hydrostatic Test, 15,000 psi
9901-150L
-
Hydrostatic test pump may be utilized as a standalone unit or combined with any of our reservoirs, safety test chambers, test fittings or other optional equipment to achieve a complete hydrostatic test system. with integral safety test chamber.
-
Product
Noise and Vibration Testing
-
Electronic Systems of Wisconsin, Inc.
ESW's unique Noise & Vibration Test Systems come fully equipped with the latest industry features. The on-screen operator display in our testers make it easy to set-up, read, track and record your noise or vibration information. We work directly with you to determine the best solution that will work for your application. Our data logging make sure that important data is stored and available for download for future reference. ESW's design engineers work to make sure the testing interface is easy for your operators to use. We work closely with our customers to make sure that your unique testing needs are met. Please see the slideshow below to see some of our Noise & Vibration Testers.
-
Product
Automated Lead Frame Testing
Sigma MAG
-
The Sigma MAG comes with an independent lead frame (un)loader for hands-free bond testing. The magazine handler is compatible with OHT and AGV and allows top and front-loading of multiple types
-
Product
Test Hardware
TTPSimulate XMC/PCIe
-
TTPSimulate is a high-performance test system which enables the simulation of a networked TTP system in real-time. It allows full hardware in the loop verification of a TTP unit. There are two form factors available for this product – PCIe and XMC card format. Both cards can act as four independent TTP nodes and have an IRIG-B interface for time-stamping.
-
Product
Supported Test Systems
-
TTCI is a leading solutions provider of application development for test systems from Seica, Keysight, Teradyne, Digitaltest, and XJTAG. We offer a wide variety of testers and test solutions to meet your needs. Our Seica Pilot and Digitaltest Condor flying probe systems can handle all of your low- to mid-volume production, prototypes, and PC boards with accessibility issues. The Keysight 3070 and Teradyne TestStation can address your larger production runs and fixture requirements. In addition, we can also address your functional and boundary scan needs.
-
Product
Low Loss Test Cables
SF Series
-
SuperFlexLow Loss Test Cables are very flexible, low loss and DC-26.5 GHz
-
Product
Wafer Level Test
-
Double sided wafer inspection system is an automatic inspection system for afterdicing wafer chip. It can do double side inspection simultaneously. The appearance defects of wafer chip are clearly conspicuous by using advanced illumination technology. Illumination and camera acquisition mode can be adjusted for various wafer process, like vertical chip or flip chip.
-
Product
CO Detector Testing
-
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
Product
Stimulus Test Cell
HA7200
-
The HA7200 enables these improvements by providing high-speed, high-accuracy temperature and pressure test for automotive sensor R&D and production. Advantest’s proprietary temperature control technology delivers an optimized test solution for high-spec pressure sensors across a broad range of temperatures, in the automotive industry and beyond.
-
Product
Stationary Meter Test Stations
Astel
-
Calmet Smart Calibration Devices
Multi position single and three phase series meter test stations class up to 0.01% for simultaneous and automatic calibration and legalization of 32/64 electricity meters
-
Product
Low to Medium Test Volume
KI-TK072
-
1310/1550 nm & 850/1300 nm source & Autotest power meter + acceptance reporting software, inspection microscope, cleaning materials. Interchangeable SC & LC connectors
-
Product
Contact Resistance Test Sets
-
When a high current passes through a pair of mechanically independent metallic contacts, the resistance must be as low as possible. An increase in resistance can lead to additional degradation, as I2R losses will cause local heating of the contact surfaces. Our range of micro-ohmmeters measure both steady state and dynamic low resistance values. With test currents up to 600A available, logging and trending are also available on some models. We ensure that our Contact Resistance tests sets are portable, making them suitable for field measurements. Our contact resistance testers’ portability makes them ideal for a vast range of resistance testing across the entire LV, MV HV and EHV spectrum.
-
Product
Altitude Digitizer Test Set & Simulator
ATS-400
-
Test & Simulate Altitude Encoder Parallel and Serial I/O all in One Rugged Test Set! The TCI Model ATS-400 is designed to test, display and simulate the output of Altitude Reporting Equipment, which conform to the ICAO Standard for SSR Pressure Altitude Transmission. In accordance with the U.S. National Standards for I.F.F. Mark X (SIF)/Air Traffic Control Radar Beacon System SIF/ATCRBS.
-
Product
Test Probes
-
Test Probes provide the vital link to transfer measurement signals as true and as undistorted as possible. Therefore these elements can be regarded as the heart of Test Fixtures – and for this very reason it is important for Equip-Test to offer high performance Test Probes with best quality and value, and thus ensure maximized ROI (Return of Investment) for our customers. Test Probes supplied by Equip-Test always provide the best-possible available solution for your contacting demands.
-
Product
Primary Injection Test Systems
-
Weshine Electric Manufacturing Co., Ltd
1.DC display primary current, secondary current test value, easy to observe and record the experiment..2.High measuring accuracy: 0.5 level.3.Small size light weight easy to carry.
-
Product
ETL Testing
-
Data is of utmost importance in digital systems. Protecting data, therefore, is of utmost importance. ETL refers to Extract, Transform, and Load. It supports the movement of data from its source to storage. With ETL testing we ensure that the data is not lost or corrupted during this movement. Huge volumes of data are collected in various formats and sources. The mapping process of these data is error-prone and can have quality issues.
-
Product
Specialized Machines And Custom Test Stands
-
PSE AG has been developing test stands for many years for a wide variety of clients and uses. If you don’t see exactly the specialized test stand you need for your innovative research, we will design and develop it for you. The following are some examples of test stand solutions that we have developed in cooperation with research institutes and industry clients:
-
Product
Optics Test Systems
Mirror Collimator And Autocollimator
-
Optik Elektronik Gerätetechnik GmbH
Mirror collimator and autocollimator for the entire wavelength range from UV to MIR The compact mirror collimator can be used both as an autocollimator and as a telescope.
-
Product
Flex Test Fixtures
-
FTFs are test fixtures which are dedicated for testing flex-based components and assemblies such as displays, touch panels and more. A weak spot in a typical functional test system is the method to connect DUT flexible cable to a circuit board where the simple method of attaching the flex directly with an ZIF or LIF connector fails.
-
Product
Test Handler
JOT M5
-
Simple, cost-effective way to automate PCB and pallet based testingSafe, reliable product handlingQuick-adjust ease: no product-specific partsFaster handling of smart productsIndustry 4.0 autonomous interconnectivityTruly scalable for growing test needsReusable, application-specific test boxesM-TestBoxes compatible with M1 handlerBoxes are fully independent, just pull out from M5 rack and use in off-line testingFail product separation to integrated magazineSpacious service-friendly constructionErgonomic workspaceTouchscreen UI with base statistics and service capabilityEasy start-stop operabilityAutomated width adjustment
