Optic LIght Sources
Produce an optical signal from a laser diode or LED.
-
Product
Optical Modules
-
VI Systems GmbH introduces the fiber coupled 850nm vertical cavity surface emitting laser (VCSEL) transmitter module VM64-850M for data rates of up to 80 Gbit/s. The transmitter module features a V-connector for the electrical input signal and for the optical output a 50/125 multi mode fiber which is terminated with a standard FC/PC connector. The left picture below shows the module. The picture on the right shows an optical eye diagram at 32 Gbaud (64 Gbit/s) in a back-to-back test configuration as tested by partners at the Heinrich Hertz Institute in Berlin.
-
Product
2 kHz C Band Fast Swept Tunable Laser Source
CA92050-KT
-
The CA92050-KT 2 kHz fast swept tunable laser modules offer superior performance for the test of Fiber Vibration Sensing, DWDM components, AWG , WSS, OPM components, Fiber sensing( especially for vibration fiber sensing application) , optical amplifiers, and other general purpose of fiber optical test and measurement with high wavelength resolution applications.
-
Product
PI/O Optical Transceiver
-
GCI's sensors are the preferred solution for E84 optical communications. GCI's full line of PI/O transceivers are fully compliant and are compatible with other manufacturers' sensors that conform to the SEMI Standard E84. Leading 300mm FABs, OEMs, and EFEM manufacturers choose the GCI sensor for its superior reliability and stability.
-
Product
Fourier Transform Optical Spectrum Analyzer, 600 - 1700 nm
OSA202C
-
Thorlabs' Optical Spectrum Analyzers (OSAs) perform highly accurate spectral measurements. Compatible with fiber-coupled and free-space light sources, these compact benchtop instruments suit a wide variety of applications, such as analyzing the spectrum of a telecom signal, resolving the Fabry-Perot modes of a gain chip, and identifying gas absorption lines. Many commonly available OSAs use grating-based monochromators, which have slow acquisition times due to the need to mechanically scan the grating and average out noise at each wavelength. Thorlabs' OSAs acquire the spectrum via a Fourier transform using a scanning Michelson interferometer in a push/pull configuration. This approach dramatically improves the acquisition time, enables a high-precision wavelength meter mode with 7 significant figures and ±1 part-per-million accuracy, and allows the included software to provide robust statistical analysis of the acquired spectra, as explained in the Design tab.
-
-
Product
Pulsed Source Measure Unit
-
The SpikeSafe SMU is a precision pulsed source measure unit that precisely sources pulsed current and simultaneously digitizes voltage. Optimized for precise and repeatable high-power LED and laser testing, SpikeSafe™ SMU (Source Measure Unit) current sources deliver precise pulsing with low microsecond rise times, low-jitter triggering and integrated digitizer for more accurate and repeatable high-power LED and laser testing.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-514-M62.5
Multiplexer Module
The 40/42-850A-514-M62.5 is a PXI/PXIe 4-channel multiplexer with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Optical Test And Measurement
-
Any type of fiber optic interconnection requires its interfaces to be free of dust and scratches in order to reach the lowest transmission loss. Small, handheld and battery powered inspection tools are available from AMS Technologies for inspection of fiber optic connectors in the field as well as high resolution type microscopes suitable for use in a production environment for qualifying the endface preparation. Additional S/W tools can support the user in making a quick decision if a certain defect is acceptable or if the surface fault disqualifies it for further use. Small and lightweight test equipment for measurement of the transmitted power in an optical fiber is needed wherever technicians handle optical fibers. Our product portfolio comprises light sources for various wavelengths, power meters for the visible and infrared and integrated solutions for sources and meters as well as optical time domain reflectometers (OTDR) coupled with visible wavelength light sources for easy fault detection within a fiber optic link.
-
Product
Fiber Optic Power Meters and Fault Locators
-
Fiber optic communication systems require the right tools to commission new links and to troubleshoot existing links. Fluke Networks has a wide range of Fiber Optic testing products to help certify that power losses are within standards and to troubleshoot broken and high loss links on single mode and multimode fiber. Fluke Network fiber optic tools are designed to be rugged and reliable, and to get the job done.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber
40-850A-114-HI
Multiplexer Module
The 40/42-850A-114-HI is a PXI/PXIe 4-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
- RS-485 to Fiber Optic Converter
Model 276A
-
FEATURES: Data Rate to 1 MBPS; ST Connectors; DB-25 Connector; Half-duplex operation; Extends distance of RS-485 network to 6,600 ft (2 km) on multimode fiber cable. The Model 276A provides the capability of transmitting an RS-485 signal via a fiber optic link.
-
Product
OLP - Optical Line Protection
-
Nanning Xionghua Photonics Technology
OLP - Optical Line Protection by Xionghua Photonics
-
Product
Laser Diode Source Product Family
LDS-7200
-
5 nanometers tuning range• 10 picometer setpoint accuracy• 0.1 picometer resolution• 20mW output power• 0.005 dB power stability• Built-in coherence control• Integrated function generator• USB remote interface• Application program with source code
-
Product
32-CH Sourcing Type Digital Input EtherCAT Module
EPS-1032
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
Polymer Optical Fiber (POF) Contacts
-
VPC offers Polymer Optical Fiber (POF) contacts in the form of patchcords. POF supports low-speed, short distance applications.
-
Product
Optical Variable Attenuator
TW3303
-
Techwin(China) Industry Co., Ltd
The Perfect Handhold Tester Series Optical Variable Attenuator TW3303 TW3303 handhold optical variable attenuator is used for continuously variable optical signal attenuation. As the attenuator is used in the laser system for the on-line testing, there, thereforeTW3303 can be used in the digital system of communication devices (such as: PHD, SDH) and also in the system of adopting analog modulation (CATV
-
Product
Light 0.83 (24.00) - 2.00 (57.00) High Performance Lead Free Probe
LFRE-1L24-2
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Tunable Narrowband Terahertz Laser Source
TeraTune®
-
The TeraTune® provides a tunable narrowband terahertz source with a tuning range from 1.5 to 20 THz and a bandwidth of less than 100 GHz.
-
Product
Optical Dissolved Oxygen Meter
OD-10
-
Measurement of dissolved oxygen for aeration flow rate control at sewage treatment plants and monitoring of water quality at rivers,lakes,and etc.
-
Product
Fiber Optic Type Chemical Concentration Monitor
CS-600F
-
The CS-600F achieves a higher level of functionality best suited for manufacturing, such as the ability to perform in-line measurement of high temperature chemical solutions in various applications, stable operation for reduced downtime, and compact size for improved space productivity in order to meet the precise chemical solution concentration management required in leading-edge semiconductor wet process.
-
Product
1KVA Variable Frequency Power Source
CX- 9001
-
Shenzhen Chuangxin Instruments Co., Ltd.
1KVA Variable-Frequency Power Source
-
Product
Light Intensity Distribution Tester
HP860LED
-
Hangzhou Hopoo Optoelectronics Technology Co., Ltd
It is specially used to measure the photoelectric parameters of LED light distribution curve (LED light intensity distribution), beam angle, normal light intensity, forward voltage, reverse current, reverse breakdown voltage and other photoelectric parameters, in line with CIE pub.No. 127 condition A or B. This system achieves high-precision testing of the optical and electrical properties of LEDs, provides LED manufacturers with sufficient LED optical and electrical parameters, and makes the development and production of LEDs more effective and reliable.
-
Product
RFoG 4 Ways or 8 Ways Return Path Optical Receiver
RFoG6000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
RFoG6000 series Return Path Receivers are an integral part of two-way RF access networks, converting upstream optical signals into RF signals at the head-end or remote hubs. 4 or 8 independent receivers are packaged in a 1RU 19-inch rack-mounted unit, serving 256 RFoG optical network terminals (ONTs). A low-noise receiver design improves noise performance by 4dB or more over typical return receivers. Low noise enables DOCSIS 3.0. -32dBm receives sensitivity, allow upstream PON-bound design, such as: supporting 32 splitting way in 20km, 64 splitting way in 10km.
-
Product
Co-Packaged Optical Interleaver
-
Co-packaged interleaver consists of a pair of iterleavers in the same package. There are three input ports and three output ports. The interleaver pair may contain one interleaver (Mux) and one deinterleaver (DeMux), or a pair of (Mux) interleavers, or a pair of (DeMux) interleavers. Customers can specify configurations according to their design and applications.
-
Product
Optical Fiber Transceivers
-
Optical Fiber Transceiver Module is a self-contained component that can both transmit and receive. Usually, it is inserted in devices such as routers or network interface cards which provide one or more transceiver module slot (e.g GBIC, SFP, XFP). Fiberinthebox provide a full range of optical transceivers, such as SFP+ (SFP Plus) transceiver, X2 transceiver, XENPAK transceiver, XFP transceiver, SFP (Mini GBIC) transceiver, GBIC transceiver, CWDM/DWDM transceiver, 40G QSFP+ & CFP, 3G-SDI video SFP, WDM Bi-Directional transceiver and PON transceiver.
-
Product
Forensic Light Source
CrimeScope CS-16-500W
-
The flagship of the SPEX Forensics Product Line, the CS-16-500W was designed for those departments that prefer the power and IR capabilities of 500W Xenon lamps.
-
Product
RS232 Mode SI-module With Optical Isolation
MX232-G
-
RS232 mode SI-module with optical isolation
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-218-M62.5
Multiplexer Module
The 40/42-852A-218-M62.5 is a PXI/PXIe 8-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Long Life Seismic Energy Source
1900LLX-T
-
Output volume of 10 cubic inches to 250 cubic inches. Light weight enough for shallow draught vesselsPowerful enough for blue water seismic surveys. Available with engineered seals for more robust performance.
-
Product
PXI Dual 2 x 2 Fibre Optic Mux LC
40-860-422
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
