Circuit
-
Product
Power Probe III Set
PP319FTC
-
Full functioning voltmeter measures in 1/10th of a volt increments from 1/10th of 1V up to 70V. Easy to read dual polarity indicators: red (+) symbol indicates positive green (-) symbol indicates negative. Circuit breaker protects the vehicles electrical system and your Power Probe. 20' extension lead gives you 40' total of lead. Great for RV'S, trucks and trailers.
-
Product
Digital Earth Resistance Testers
ST-1520
-
Capable of measuring earth voltage.2mA measuring current permits the testing of earth resistance without tripping earth leakage current circuit breakers in the circuit.Auto power off function.The timer operates automatically for approximately three to five minutes when the "push button switch" and "timer on button" are pressed together.
-
Product
Power Distribution Boards
-
Power distribution systems can be offered in addition to solutions for power supplies. This includes power distribution boards, which take over the power distribution in your system. When developing the system solution, in addition to the technical requirements such as high energy efficiency, simple further processing is decisive. The competence for high-performance circuit boards, enclosure constructions as well as assembly and system tests, which has been developed over the years, enables us to offer you the best possible power supply and distribution.
-
Product
Circuit Module, Riser for ISMB 2U PCIe X16 Riser Card to 2 PCIx8 Expansion Slots , and PCI card
AIMB-RP3P8-12A1E
-
Support ISG 2U chassis
-
Product
IGBT Drive
-
IGBT gate drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode, signal processing circuit and power output transistor on the output side in a single chip. This coupler is designed specifically to provide high common mode transient immunity (CMR) and a high output current, and has an active miller clamp and high switching speed, making it ideal for driving IGBTs and MOS FETs.
-
Product
Power Supply 605D-II
-
reliable and precise power of the output DC stabilization and digital LED displays. The output voltage is adjustable from 0 ~ 15V DC in smoothly with the knobs to control coarse and precise. Output current is regulated (limited) fluent in 0.6A ~ 2A. Securing the power supply protects it against accidental short circuits, and thus against overload and damage. In addition, the power supply has 5 fixed output voltages: 1.5 V, 3.6 V, 4.8 V, 6 V and 7.2 V, specially designed for mobile services, power systems and electronic components, etc. can be used in the design of electronic products, scientific work in laboratories, production lines and in teaching. Power can be used in the design of electronic products, scientific papers, laboratories, production lines and in teaching.
-
Product
500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm
PP021-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
Product
IPM Drive
-
IPM drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and signal processing circuit on the output side in a single chip. This coupler is a high common mode transient immunity (CMR), high CTR type whose pulse width changes according to the operating temperature, making it ideal for driving IPMs (intelligent power modules).
-
Product
VME Test Extender 6U/220mm Universal
110EXT6122-000X
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Tone Coax Cable Generator
240 HAL
-
The AINES 240 HAL Tone Generator is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
-
Product
Matched Transistors
-
Analog Devices offers dual and quad transistors with excellent matching characteristics. Offset voltages, temperature drift, and hFE matching are individually tested to data sheet specifications. Device performance is guaranteed over industrial and military temperature ranges. Each of these devices is an excellent choice as an input stage for an amplifier or in log/antilog circuits. ADI’s matched transistors offer low noise and high gain, with characteristics approaching an ideal transistor.
-
Product
Electrical Testers
-
When you work with electricity, you want tools that are field tested and proven to meet the highest standards. All Amprobe tools undergo rigorous examination in our state of the art testing labs, ensuring quality and full compliance with the latest IEC and CE safety regulations. They are also listed with third party certification labs worldwide. Amprobe electrical testers include circuit tracers and testers, non-contact voltage detectors, voltage meters, socket testers and more to cover all aspects of electrical testing.
-
Product
Switches
-
Whether you are performing high-accuracy, low-speed measurements on a dozen test points or high-channel, high-frequency characterizations of integrated circuits, National Instruments delivers a flexible, modular switching solution based on PXI or SCXI to help you maximize equipment reuse, test throughput, and system scalability.
-
Product
Amplifiers
-
Is an electronic device that can increase the power of a signal (a time-varying voltage or current). It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output.
-
Product
BNC Twinax Connectors
-
BNC Twinax connector category has several part numbers, the majority are RoHS and REACH compliant. BNC Twinax connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our BNC Twinax connectors are built to precise industry specifications. Pasternack BNC twinax connector items are available in jack or plug gender with 78 Ohm impedance. Connectors in twinaxial BNC are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These BNC Twinaxial connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this twinax BNC connector series is in-stock. In addition to being in stock, these twinaxial BNC connectors will ship the same day as they are purchased.
-
-
Product
Loop / PFC Testers
-
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2715 is a loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
Product
Radio Based Ammeter & Voltmeter
Troubleman’s Kit
-
The SensorLink Troubleman's Kit consists of the Radio Ampstik and the radio-based Voltstik. These instruments are designed to assist the modern day electric utility troubleshooter in resolving problems in their low and medium distribution circuits.
-
Product
Microcontrollers
-
A compact integrated circuit designed to govern a specific operation in an embedded system.
-
Product
Mini UHF Connectors
-
Pasternack Mini UHF connector category has many part numbers, most of which are RoHS and REACH compliant. Mini UHF connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These Mini-UHF connectors are built to precise RF and microwave industry specifications. Mini-UHF connector products are manufactured in male or female gender with 50 Ohm impedance. UHF mini connector products are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These connector series in mini UHF designs include crimp/solder or solder attachment methods. Other mini-UHF connector options include Push-On or standard configurations. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this mini UHF connector series is in-stock. Not only are these in stock, they will ship the same day as well.
-
Product
(70×90×15mm) C-Band DWDM Full Function Pre EDFA Module
WPA4300-FM02
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Huatai WPA4300-FM02 series with 70 × 90 × 15mm MSA compact package, is a digital control circuit with DWDM full function preamplifier module. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Suitable for C-Band 44 or 88 waves DWDM system applications.
-
Product
Analog Control Cable for Electronic Loads
EE105T-xx
-
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
Product
WaferPro Express On-Wafer Measurement Program Software
-
WaferPro Express software performs automated wafer-level measurements of semiconductor devices such as transistors and circuit components. It provides turnkey drivers and test routines for a variety of instruments and wafer probers. Its new user interface makes it easy to setup and run complex wafer-level test plans, while powerful customization capabilities are enabled by the new Python programming environment.
-
Product
Split type AC Current Transformer
CTS-200
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Short circuit switch for secondary output is provided for safe operation.*High accurate transformer for the application of first class meter.*Easy installation by metal fitting.
-
Product
Fixed Attenuators
-
In circuits are used to lower voltage, dissipate power, and to improve impedance matching. In measuring signals, attenuator pads or adapters are used to lower the amplitude of the signal a known amount to enable measurements, or to protect the measuring device from signal levels that might damage it.
-
Product
Inbuilt External Controller ATE with Touch Screen Features
QT 200NXT
-
Qmax Test Technologies Pvt. Ltd.
QT 200 nxT is a ultra modern stylish Inbuilt external controller ATE with touch screen features, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software. The vast library support helps you to functionally test host of different IC families. Other features like user-friendly Windows based software, add-on utilities like oscilloscope, RCV meter circuit tracer, etc. makes it a favorite and makes very effective for repairing PCBs without schematic/ circuit diagrams. All these tests are carried out using simple BUT Interface like multipin test clips, probes or custom test fixture
-
Product
VME Test Extender 3U/220mm J2
111EXT3122-12XX
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Inductor Products
-
Macom Technology Solutions Holdings Inc.
They provide uniformity, durability and repeatability in circuit fabrication. The coils are polyimide coated to protect from ambient contaminants, and to eliminate the need for conformal coating. Quartz substrates are rugged and reduce dielectric losses. Chips may be bonded using either conductive or non conductive epoxies, and wire bonded with gold wire or ribbon by thermocompression bonding.
-
Product
Electrical Testers
-
The Fault Trapper is a new class of tester using Spread Spectrum Time Domain Reflectometry (SSTDR) to monitor energized circuits.
-
Product
Embedded Boards
UltraZed Family
-
Embedded boards are boards with processors, multiple integrated circuits, interfaces and other essential components assembled on it to serve a dedicated function. Embedded boards comprise multiple technologies, including processors, core logic, networking, connectivity, and multimedia components to provide functionality and performance for embedded system design applications. Embedded boards and solutions are normally employed to ensure a faster time to market for the developer. Applications of embedded systems vary from tiny portable devices, to large commercial and industrial installations, and even largely complex systems like medical or military or aviation purposes. Embedded boards can have single MCU chip or multiple MCUs depending on the complexity of application.
