Showing results: 631 - 645 of 812 items found.
-
National Technical Systems
Fourier Transform Infrared Spectroscopy (FTIR) is a standard technique used in the identification of contaminating materials on the surface of printed circuit boards (PCBs) and around the leads of electronic components (BGA, capacitors, resistors, inductors, connectors, diodes, oscillators, transformers, IC, etc.) on printed circuit assemblies (PCAs). Additionally, FTIR can be used for “simpler” identifications, such as determining a specific type of plastic or rubber compound.
-
KT-96A -
KILTER ELECTRONIC CO.,LTD
LCD Max. Indication 3999,with length unit. Locate the broken point of a cable. With RS-232 interface, it can be connected to your computer. Takes a new ¡°VECTOR MEASUREMENT¡± technology in measuring the length of the cable. Length Test Range:400m/4000m/40km. Accuracy: ¡À1% rdg ¡À 0.3m. For use in computer network, CATV, communicate engineering. With Volt, Resistance,continuity,diode test
-
VX Instruments GmbH
The digital multimeter (DMM) is the all-rounder of electronic measurement technology. It is used to measure the basic electrical variables of voltage, current and resistance potential-free. Many devices also offer a wide range of additional functions, such as the measurement of electrical capacity, test functions for diodes or transistors and much more. Some devices also allow to record signal curves, which is equivalent to the function of an isolated digitizer.
-
CPCI-48IN -
ALPHI Technology Corporation
The input board consists of three Zilog Z8536 controllers for DC input control. An FPGA provides the timing and control. Each input has its own optical isolation, and supports a hardware adjustable resistor/opto-diode combination for various input voltage ranges. An AMCC PCI controller provides the interface to the host computer. All I/O is accessible from the front panel.
-
6400 DM -
Standard Electric Works Co., Ltd
● 4000 counts LCD with a maximum display of 3999.● Angled display design helps the user to identify the reading of value easier.● Auto ranging designed.● Range change function.● Continuity check.● Diode measurement.● Data hold function.● Low battery indication.● Over range indication.● Fuse protection.● Special hook design used to hang the meter for ease of use.
-
PDMT25 -
Pyle Audio Inc.
4000 Display CountPeak Capture ModeData HoldMax/Min Recording ModeVoltage DC: Max Range 1000 V, Accuracy +/- 0.5%Voltage AC: Max Range 1000 V, Accuracy +/- 0.8%Current DC: Max Range 10 A, Accuracy +/- 1.2%Current AC: Max Range 10 A, Accuracy +/- 1.8%Resitance: Max Range 40 M, Accuracy +/- 0.8%Duty Cycle: Max Range 99.9%, Accuracy +/- 1.2%Temperature: Max Range 760 C / 1400 F, Accuracy +/- 3.0%Frequency: Max Range 10 MHz, Accuracy: +/- 1.5%Capacitance: Max Range 40 mF, Accuracy +/- 1.5%Diode Check
-
ERF-5W™ Series (Single & Dual) -
Pole/Zero
The new ERF-5W™ filter takes Pole/Zero’s MINI-ERF® technology to a higher level of RF power handling, with 5W (average) in-band power handling, and covering the entire military tactical radio tuning range of 30-520 MHz in one integrated package. This tunability is accomplished by the use of three poles of selectivity, multiple internal tunable filters along with high performance PIN diode RF band select switches. The tunable filters are designed to minimize size and power consumption, while maintaining high RF power handling and linearity characteristics. Serial control is accomplished via a standard Serial Peripheral Interface (SPI)-based bus.
-
KT3202 -
Ketai instrument (kunshan) Ltd.
It has AC and DC voltage, DC current, resistance, capacitance, continuity, and diode measurement functions.Comply with safety standard CAT III 600V Fuse Φ6x31mm 600VKT3202 is a specially designed AC and DC voltmeter.KT32034 specially designed AC and DC ammeter.KT3204 is a specially designed DC low-current, low-voltage meter. The voltage can be measured from 0 to 100mV, and the current can be measured from 0 to 50uA.The pointer "0" is at the median value, and the voltage and current are divided into two sides.This set of four tables has certain practical significance for students' knowledge and understanding of Ohm's law in electrical engineering.This set of meters complies with the CAT III 600V standard.
-
KT3204 -
Ketai instrument (kunshan) Ltd.
It has AC and DC voltage, DC current, resistance, capacitance, continuity, and diode measurement functions.Comply with safety standard CAT III 600V Fuse Φ6x31mm 600VKT3202 is a specially designed AC and DC voltmeter.KT32034 specially designed AC and DC ammeter.KT3204 is a specially designed DC low-current, low-voltage meter. The voltage can be measured from 0 to 100mV, and the current can be measured from 0 to 50uA.The pointer "0" is at the median value, and the voltage and current are divided into two sides.This set of four tables has certain practical significance for students' knowledge and understanding of Ohm's law in electrical engineering.This set of meters complies with the CAT III 600V standard.
-
COMM-connect
The COMM-connect Entry Level Broadcast Power Monitor type 3025 can control two external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. Equipped with the RMS Probes the Power conversion algorithms handles multi carrier, multi mode signals. With the 3026 Diode base probe the power readout gives good repeatable results. The power readout is auto scaled and VSWR will be calculated between the two probes. The COMM-connect Entry Level Power Monitor gives a number of application to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
Extech SDL400 -
Extech Instruments Corporation
The SDL400 records data on an SD card in Excel format. Wide range to 10,000Fc or 100kLux. Cosine and color-corrected measurements. Utilizes precision silicon photo diode and spectral response filter. Offset adjustment used for zero function to make relative measurements. Adjustable data sampling rate. Stores 99 readings manually and 20M readings via 2G SD card. Type K/J Thermocouple input for high temperature measurements. Large backlit LCD display. Record/Recall Min, Max, Data Hold and Auto power off. Complete with 6 x AA batteries, SD card, hard carrying case and light sensor with protective cover.
-
Autobuild™ -
CAMI Research Inc. (CableEye®)
Our optional, add-on AutoBuild™ software (Item 728) offers Guided Assembly for cables and wire harnesses. Use a supplied probe, or a finger with wrist strap, to touch an unterminated wire and the software shows (and says) exactly where the wire should be connected. As the operator attaches each new wire, AutoBuild checks the entire assembly and provides a clear checklist showing all completed good connections. When using our resistance-capable testers, you may connect diodes and resistors by name and value, check resistance values over the tester's specified range, and test conduction and isolation resistance against specified thresholds. Programmable tones accompany the graphic screen to give clear signals to the operator when good connections are completed or when incorrect connections, resistance violations, or diode insertions are detected. Combine with our Light Director™ option for light-guided assembly.
-
DCM402 -
Draper Tools Ltd
Expert Quality, auto and manual ranging clamp meter capable of voltage, current, resistance, diode, continuity, capacitance, frequency, duty cycle and temperature testing. Maximum jaw - opening diameter of 36mm, backlit LCD screen, auto power off, linear bar graph functions and a useful inspection light. Supplied with test leads, temp probe, case and 3 x AAA batteries.
-
Insight Product Company
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Renesas Electronics Corp.
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a high-accuracy D/A converter on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.