Analog Input
measurable voltage value.received from a sensor.
-
Product
Analog Output DAQ Cards
-
Analog output cards are ideal for DAQ applications where multiple A/O channels are needed for voltage and current output.
-
Product
Analog Control Variable Gain Amplifiers (VGAs)
-
Analog Devices voltage controlled variable gain amplifiers provide continuous gain control over a wide dynamic range for a variety of audio and optical frequency bands. Our VGAs improve the dynamic range of a circuit by allowing users to adjust a signal’s amplitude in real time, which is invaluable for ultrasound, speech analysis, radar, wireless communications, and instrumentation-related applications.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
8-Ch Digital Input EtherCAT Slice IO Module
AMAX-5051
EtherCAT Slice IO Module
Channels: 8Digital Input: Dry Contact Logic level 1: close toIso.GND; Logic level 0: open; Wet Contact Rated voltage: 24VDC; Logic level 1: 10~30 VDCand -10~-30 VDC; Logic level 0: -3~3 VDCInput Delay: From logic level 0 to 1: 4ms; From logic level 1 to 0: 4msDigital Filter: 3ms
-
Product
Digital-To-Analog Converter
DAC-200
-
Advanced Thermal Solutions, Inc.
The DAC-200 is a digital-to-analog converter designed to convert the output of the ATVS family of instruments to 0-5VDC. The device produces an output whereby the voltage is linearly proportional to both the air velocity and temperature for the ATVS product family, including the ATVS-Nxt, ATVS-2020, eATVS-4, eATVS-8, and iQ-200.
-
Product
Isolated RTD Input Module
ADAM-3013
Thermocouple Signal Conditioner
1000 VDC 3-way optical isolationBuilt-in microprocessorSwitch configurable for 0~5 V, 0~10 V or 0~20 mA outputsSwitch configurable Pt and Ni RTD input ranges
-
Product
9 Inputs Satellite Multi-Switch
HJMS-900B (Stand alone)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*8 satellite IF & 1 terrestrial TV inputs. *Built-in amplification circuit to compensate cable loss.* 13/18V.22KHz and DISEqC. *Suitable for residential multiple LNBs reception. *Sheet Metal Housing.
-
Product
Analog Multimeters
-
Mirrored Scale reduces errors due to parallax 13 Versatile ranges, ideal for use in shop, home, boat, car, ect.2k/V DC/AC sensitivityRecessed input terminals for safe useFuse and doide protection
-
Product
High Speed Digital Analog
ITA
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
Product
Smart Inductive Analog Measurement Sensors (AMS)
-
Contrinex Smart Inductive Analog Measurement Sensors (AMS)
-
Product
Analog Clamp Meter
-
Operation0C~ 40C(32~104)/<80% R.H.(no condensation) Storage-10C~ 50C(14~122)/<70%R.H.(no condensation) Dimension & Weight 243(L)x91(W)x45(H)mm Approx.360g (Including battery) Accessories Battery UM-3 (AA) 1.5V x1 Instruction Manual x1 Test Lead (red + black) x 1 Carrying case x1 Optional Accessories Temp. Probe (NR-81) AC Line Splitter(DE-10ALS) *Applicable to electrical appliances small current
-
Product
Oscilloscope 40 GHz, 4 Channels, 1.85 mm Inputs
UXR0404B
Oscilloscope
XR0404B Infiniium UXR-Series is the 40 GHz, 4 channel, 1.85 mm input, Infiniium UXR-Series real-time oscilloscope.
-
Product
Analog Controller Meters
-
Accuracy 0.05% F.S.±1digit Measuring six channel DCA/DCV/Pt-100/Thermocouple/etc... Programmable rate -1999 to 9999 digit Input channel number(1~6) can be modified Digit RS-485 interface function (optional) CE EMC certification
-
Product
Temperature Module
U1586B
Temperature Input Module
The U1586B temperature adapter expands the capabilites of your handheld oscilloscope or handheld digital multimeter to measure temperature, either in °C of °F. To be used with a K-type bead thermocouple, and with approximately 1600 hours battery life with an alkaline battery, this adapter ensures you get the most out of your handheld scope or DMM purchase.
-
Product
Buffered Analog Multiplexers
-
Analog Devices’ leading edge buffered multiplexers are designed in single, dual or triple independent channels with two inputs (2:1) or four inputs (4:1) and are offered in standard plastic packages, as well as in space saving LFCSP packages. These multiplexers are very high speed primarily useful for switching video and RF signals with either 50 ohms or 75 ohms systems.
-
Product
Analog Insulation Resistance Tester (CE)
MIS-A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
The single and fluorescent scale indicator for 3 ranges insulation measurements enabled easy observation. Especially, useful when working in dark place. Hand free and continuous measurements with custom made switch. Safe design with built in automatic discharging function for any capacitors present in the circuit. The voltage in the circuit can be pre-checked without any switch operation for safe insulation measurements. Compact, light weight and heavy duty rugged case.
-
Product
40 mA to 800 mA EN Series Analog System
-
An EN modular multi-channel solution is composed of an ENT power supply, one or more ENV controllers/amplifiers and a case. Depending on the specific application, multiple control modules can be used. This allows for the most cost effective solution for the highest precision piezo control system.
-
Product
Saluki LSG022 Analog Signal Generator (Modular)
-
Saluki LSG022 analog signal generator offers 100kHz to 22GHz frequency coverage with 10ms frequency switching speed. It can be used independently or combined with the chassis to form a test system.Saluki LSG series signal source is the cost-effective choice when you need to balance budget and performance. It provides the signals you will need for radar performance evaluation, high-performance receiver test and components parameter test etc..
-
Product
17 Inputs Satellite Multi-Switch
HJMS-171700 (Cascadable)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*16 satellite IF & 1 terrestrial TV inputs. *Built-in amplification circuit to compensate cable loss. *13/18V.22KHz and DISEqC Switching. *Suitable for residential multiple LNBs reception. *Cascadable. *Sheet Metal Housing. *Adaptor type SMPS power supply.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
PCI Express 16 Isolated Input Digital Interface (10-30V)
8006He
-
Optimized for sensing up to 24V inputs, the 8006He PCI Express digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, pushbuttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
AC Input Single
-
AC input/single transistor output photocouplers (optocouplers) are optically coupled isolators containing GaAs infrared light emitting diodes and an NPN silicon phototransistor. This type consists of two infrared light emitting diodes connected in inverse-parallel, and operates directly on AC input current.
-
Product
16-Bit ,32/16-Ch Analog Output PCIE Card
PCIE-1824
PCI Express Mini Card
32/16 high-density analog output channelsFlexible Output Range: ±10 V, 0 ~ 20 mA and 4 ~ 20 mASynchronized output functionKeep output values when hot system resetHigh ESD protection (2,000 VDC)Board ID switch
-
Product
96 Channel Isolated Digital Input / Interrupt Output Module
DP-cPCI-3096
-
96 Channel Isolated Digital Input / Interrupt Output Module
-
Product
Analog Oscilloscope
FS-404
-
*OSCILLOSCOPE: 40 MHz Dual Trace,Dual Trigger, 1mV Sensitivity, 10ns Resolution.*FUNCTION GENERATOR: 0.5Hz~5MHz Frequence, Sine,Square,Triangle,3 waveforms, Max output:20 Vp-p(No Load),10 Vp-p(50Ω? Load)., TTL Synchronous Output
-
Product
Telephone Line Testers for POTS / Analog Line
-
*This analog line tester is suitable for all instalers installing telephone equepement on POTS line.*Led indications signaling the status of analog line.
-
Product
Oscilloscope - 500 MHz, 4 Analog Channels
DSOX4054A
Oscilloscope
500 MHz4 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
8/16-CH 16-Bit Analog Output Cards
PCI-6208/6216 Series
Analog Output Module
ADLINK PCI-6208/6216 series are 8 or 16-CH, 16-bit, analog output cards. The PCI-6208V-GL offers 8 voltage outputs with ±10 V range, featuring 15-bit monotonicity and 10 V/μs slew rate. The on-board analog switches minimize the power-on glitches. PCI-6216V expands the voltage output channels to a total of 16 for higher analog output density requirements. In addition to the voltage output functions, the PCI-6208A features 8 current outputs with ranges of 0-20 mA, 4-20 mA, and 5-25 mA. The daughter board EXP-8A provides high-quality voltage to current transducers. The PCI-6208A device is capable of delivering 14-bit monotonicity with 1.3 mA/μs slew rate. ADLINK PCI-6208 series devices provide high-resolution, high-density analog output functionalities and are suitable for ATE, signal generation, industrial process control, servo control and other industrial control applications.
-
Product
Low Power Analog to Digital
7430
-
Smart A/D for thermocouples, thermistors, RTD's, strain and pressure gauges8-channels of 16-bit A/D resolutionEliminates trimpot adjustments by using software calibrationPerforms concurrent 32-bit floating point operations to minimize host computer loadingEach channel is software programmable for sensor type, gain, low-pass filtering, scan rate
-
Product
Temperature Input Device
-
The Temperature Input Device is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take temperature measurements with your PC. You can connect the Temperature Input Device to any USB port to use your PC as a display and monitor data in real time. The device is compatible with J, K, R, S, T, N, E, and B thermocouples.The Temperature Input Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
