cPCI
Compact PCI is designed to address the needs of industrial/embedded users who need the performance and functionality of PCI in a more rugged package.
See Also: Compact PCI, CompactPCI Express
-
Product
64 Channel Isolated Digital Input / Interrupt Output Module
DP-cPCI-3069
-
DP-cPCI-3069 provides 32 Channel Digital Input / Interrupt and 32 Channel Digital Output with isolation. 32 Channel Inputs and 32 Channel Outputs are divided into groups of 16 channels each and are routed to rear I/O only.
-
Product
Programmable Multifunction Counter Board, Isolated, w/ 4 Function Modules & BISS-Master Logic
CPCI-1710-10K20
-
The board CPCI-1710 is a fast multifunction and multichannel counter board for the CompactPCI bus. The strengths of this board are its wide range of applications and high precision and reliability for though industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provides the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied sofware. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed or reconfigured as further requirements arise.
-
Product
Quad Channel Serial Communication Controller
CPCI-SCC04-ISO
Controller
The CPCI-SCC04-ISO Module is a quad Channel serial Communication controller with 2K Fifo per Line. The CPCI-SCC04-ISO module is based on 4 enhanced Z85233, with larger FIFOs and several SDLC improvements from Zilog. This module provides four synchronous ports up to 230 kbaud synchronous ports and up to Data Rates up to 5.0 Mbit/Sec full-duplex channels, with an independent baud rate generator for each channel.
-
Product
Compact PCI Connector Board
cPCI-J2-SCSI
-
Ribbon cable is used between the rear IO and SCSI connector. The lengths are reasonably well matched. The cable is short. The design is intended for lower speed IO - 10 MHz and below. Above 10 Mhz there may be some attenuation.
-
Product
6U CompactPCI 10 Gigabit Ethernet Switch Blade
cPCI-6S10
Switch Blade
- ARM Cortex-A9 processor integrated in Broadcom BCM56150 switch- 24-port fully managed Gigabit Ethernet switch- Pre-installed ADLINK PacketManager accelerates packet processing- Layer 2/3 switching with advanced support for VLANs, QoS and IPv6- Two 10 Gigabit Ethernet SFP+ uplink ports- Supports IPMI based on PICMG 2.9 (System Management Specification)
-
Product
64-CH Isolated Digital I/O Modules
cPCI-7432/7433/7434
Digital I/O
- Two external interrupt sources for cPCI-7432/7432RP/7433- 3U Eurocard form factor, CompactPCI compliant (PICMG 2.0 R2.1)- 32-CH isolated digital inputs & 32-CH isolated digital outputs for cPCI-7432- 64-CH isolated digital inputs for cPCI-7433- 64-CH isolated digital outputs for cPCI-7434/7434P- 5000 VRMS isolation voltage
-
Product
3U CompactPCI Quad-Core Intel Atom® Processor X Series Blade
cPCI-3640 Series
Processor Blade
- Low power quad-core Intel Atom® x6413E Processor (formerly Elkhart Lake)- Up to 32GB DDR4-2400-3200MT/s ECC soldered memory- Optional onboard SSD support- Flexibility in IO selection- Extended temperature -40 to 85 degree C supported
-
Product
32 Form C High Power Relay Module
DP-cPCI-4035
-
DP-cPCI-4035 is a cPCI-based 32-channel high power relay. It is designed as general-purpose module. Applications of this module include power routing, relay outputs for soft PLCs, automatic test equipment, hardware simulation and high current measurement routing.
-
Product
DSP Based Serial Communication Board
CPCI-ISC8
Communications Module
The CPCI-ISC8 is an intelligent DSP based serial communication board. This 3U board is based on the CPCIIPC product and has been modified to remove the IPinterface and to support additional I/O features. The CPCIISC8 provides mechanical support and the electrical interfaces for an I/O mezzanine board. Multiple CPCI-ISC8 boards may be installed in a single system.
-
Product
3U CompactPCI Serial Intel® Xeon® W Processor Blade
cPCI-A3535 Series
Processor Blade
- Intel® Xeon® W-11555MRE 6-Core processor- Max. 64GB DDR4-3200 by 2x SODIMMs- 80GB 3D Nand flash SSD in SLC mode- USB 3.2, USB-C and RJ-45 iAMT front panel service ports- 2x M12 2.5GbE front panel ports for on train use
-
Product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, all isolated
CPCI-3120-8-4
-
Input range:- ± 10 V, 0-10 V software programmable- 0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V,- ± 1 V (gain)- 0-20 mA (option)- software-programmable amplifier:- PGA x1, x2, x5, x10- Conversion triggered through software,scan, timer, external event- Onboard FIFO buffering for 256 analog values- Data exchange through 16-bit I/O or 32-bit memory (PCI DMA)- Sequence RAM- Overvoltage protection- input filter: 160 kHz
-
Product
Power Supply
VITA, VPX, VME, cPCI
-
PCI-Systems Inc. intelligent power supplies integrate a microcontroller (MCU) for a fully programmable and flexible solution. Intelligent power conversion allows configuration and reconfiguration for different applications. With intelligent power conversion, the power supply becomes a platform solution for many different applications. The power supply can easily be reprogrammed to support different operating limits and control inputs.
-
Product
8 Channel 1GHz High Frequency for SBDT Relay Module
DP-cPCI-4158
-
DP-cPCI-4158 is a 8 channel high frequency SPDT relay module. It provides for 1000V DC isolation between channels. This module is constructed using SPDT relays.
-
Product
3U CompactPCI Serial 9th Gen Intel Xeon®/Core™ i7 Processor Blade
cPCI-A3525 Series
Processor Blade
CompactPCI® Serial (PICMG CPCI-S.0) is a new modular computer standard officially adopted by PICMG in 2011. The CompactPCI Serial standard defines a completely new connector to support high-speed serial interfaces including PCI Express, SATA, USB and Ethernet. A CompactPCI Serial backplane has six high-speed connectors P1 to P6 on the system slot but only P1 is mandatory on peripheral slots, P2 to P6 being optional. A CompactPCI Serial system can comprise a total of nine blades (one system blade and eight peripheral I/O blades) through an Ethernet full mesh or single star architecture. The CompactPCI® Serial standard is the next-generation of the CompactPCI® specification and provides more flexibility and higher speed and bandwidth in modular system solutions.
-
Product
6U CompactPCI Multifunction I/O Board
CPCI-MFIO-6U
Multifunction I/O
The CPCI-MFIO-6U is a 6U CompactPCI multifunction I/O board. The CPCI-MFIO-6U offers 32 channels of 16 bit A/D, four 16 bit D/A, 16 digital I/O, counter / timers, and one PMC expansion slot for additional I/O. There is a local 60 Mhz TMS320C31DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-MFIO-6U is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
Product
Single or Dual DDC ACE 1553 Controller
CPCI-1553-DDC-1
Controller
Single or Dual DDC ACE 1553 Controller, Bus Controller, Remote Terminal, Bus Monitor Modes.
-
Product
IEEE488 (GPIB, HPIB) compactPCI Interface Card
GPIB-cPCI-XL
-
The GPIB-cPCI-XL is a GPIB controller card for PXI and CompactPCI computers.
-
Product
3U Processor Board
CP32108
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP32108 is a compact modular 3U CPCI single board computer compliant with CompactPCI specification. Based on Intel® 6th Skylake-H platform, CP32108 supports a variety of processors. On CP32108, there are rich interfaces like SATAIII, USB3.0, GbE, PCIe2.0, etc. In addition, CP32108 can provide up to 1TB SSD storage with mSATA interface.CP32108 applies high-speed CPCI connector on J2, in order to transmit PCIe2.0, USB3.0, SATAIII signals. CP32108 supports up to x4 PCIe to rear with flexible PCIe configuration including 1 x4, 2 x2, 1 x2+2 x1 or 4 x1.CP32108 integrates Intel® Gen9 HD Graphics P530 display controller, and supports various display outputs like eDP, DP and HDMI(with resolution up to 2560x2160 @24Hz, 24 bpp).
-
Product
48-CH DIO & Timer/Counter Cards
cPCI-7248/7249R
Counter/Timer Module
- PICMG 2.0 Rev 2.1- 48-CH digital TTL/DTL input/output- Emulates 4/2/1 industry standard 8255 PPI (mode 0)- Direct interface with OPTO-22 compatible I/O modules Output port status read back- On board 8254 timer/counter chip
-
Product
3U CompactPCI Serial MXM GPU Carrier Card
cPCI-A3MXM
Carrier Board
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP (100mm x 160mm)- Compatible with MXM Type A (82 mm x 70 mm) or Type B (82 mm x 105 mm)- Support NVIDIA A1000 with 2048 CUDA® cores, 16 RT Cores and 64 Tensor Cores or NVIDIA RTX™ A4500 with 5888 CUDA® cores, 46 RT Cores and 184 Tensor Cores- 4x DisplayPort 1.4, support 4K (3840x2160) resolution- Operating temperature: -40°C to +70°C- Designed to meet EN50155 standards
-
Product
8/16-CH 16-Bit Analog Output Modules
cPCI-6208/6216 Series
Analog Output Module
- PICMG 2.0 Rev 2.1- 16-bit D/A resolution- 16-CH voltage on 6216V- 8-CH voltage outputs on 6208A and 6208V- 8-CH current outputs on 6208A- Bipolar analog output range- 4-CH TTL DI and 4-CH TTL DO- Rear I/O available
-
Product
128 Channel Digital I/O With 6 Channel Counter
DP-cPCI-3015
-
DP-cPCI-3015 is a 128 channel TTL compatible Digital Input / Output card with 6 counter channels. The DIO can be programmed as input or output in groups of 16 channels.
-
Product
Quad IP Carrier Module With Rear I/O
DP-cPCI-5121
-
DP-cPCI-5121 IP carrier board provides an electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.
-
Product
24 Channel, 1 Form C 5A Relay Switch
DP-cPCI-4455
-
The DP-cPCI-4455 is a 24 channel relay switch module. It provides 250V DC/AC isolation between channels. This module is constructed using 1Form’ C’ SPDT relays.
-
Product
6U CompactPCI Rear Transition Module with AMD MXM Graphics Module
cPCI-R6500 Series
Rear Transition Module
The cPCI-R6500 Series is 6U CompactPCI rear transition module (RTM) designed for use with ADLINK 6U CompactPCI CPU blades. The cPCI-R6500 is an RTM equipped with an ATI graphics module to provide additional graphics performance for embedded applications and supports comprehensive rear I/O functionality. Dual independent display output is via two DVI ports and an onboard Realtek ALC262 High Definition Audio Codec provides analog audio output from the audio controller on the CPU blade. The cPCI-R6500 requires a compatible 6U CompactPCI backplane with rear I/O support and correctly configured CPU blade.
-
Product
3U CompactPCI Multi-Function I/O Board
CPCI-AD32
Multifunction I/O
The CPCI-AD32 is a 3U CompactPCI multi-function I/O board. The CPCI-AD32 offers 32 channels of 16 bit A/D, two 16 bit D/A, 16 digital I/O, counter / timers.There is a local 60 Mhz TMS320C31 DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-AD32 is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
Product
192 Channel Isolated Digital Input / Interrupt Module
DP-cPCI-3780
-
DP-cPCI-3780 provides 192 channel digital input / interrupt with optical isolation. The 192 channel input is divided into 12 groups of 16 channels. The inputs are designed for a input voltage range from 5V to 28V.
-
Product
3U CompactPCI Serial 2.5" SATA Storage Carrier
cPCI-A3H10
Blade Server
- 3U 4HP CPCI-S.0 peripheral- One 2.5" SATA 6Gb/s drive slot- Status LEDs on faceplate: drive activity, hot-swap status, user-configurable- Hot swap support- Operating temperature: -40°C to 85°C with qualified com
-
Product
Dual Industry Pack Carrier Module
CPCI-SIP-rp
-
The CPCI-SIP module provides a 3U high performance flexible I/O scheme that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-SIP is the perfect solution.The CPCI-SIP is also available with the Industry Pack lines routed to the CompactPCI P2 connector for application that require rear panel I/O.
-
