PD Monitor
-
Product
Gas Monitor System
-
Henan Bosean Electronic CO.,Ltd.
Used to detect combustible, flammable and toxic gases, and oxygen depletion.
-
Product
Wired Hazard Monitoring
-
Grain dust is extremely volatile and can easily explode with the proper ignition source in confined spaces. OSHA has mandated that grain elevators in Class II, Division 1 environments must have the 3 monitoring sub-systems for elevator safety (1910.272(q)(4)(ii), 1910.272(q)(5), 1910.272(q)(5)).
-
Product
20Hz Injection Kit Monitoring System
-
Signals & Systems India Private Limited
The Display used to monitor the 20Hz and 50Hz current passing through NGT transformer. This could help to monitor the stator earth fault and could record the current every minute. The current shall be displayed in milliamps for both 20Hz and 50Hz. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. The current can be measured using clamp-on CT which would be clamped between load resistor and NGT. It gives an indication of the current values are lower or higher than the set threshold.
-
-
Product
Respiration Monitor Belt Logger Sensor
NUL-236
-
This sensor comes with a belt and measures the air pressure in it. The pressure changes according to the breathing of the subject. From the measured values, the respiration rate can be calculated.
-
Product
Process Ozone Monitor
Model 465M
-
Teledyne Advanced Pollution Instrumentation
The Model 465M is a microprocessor based medium range ozone monitor for measuring process ozone concentrations in water treatment, food processing, and research applications. The design has been specifically optimized for applications requiring the measurement of ozone at near-ambient pressure such as water treatment contactor off-gas measurement. The Model 465M has been designed to give accurate and stable readings over long time periods with little or no maintenance or calibration. The Model 465M is available in a NEMA 4X wall mount enclosure.
-
Product
Monitoring Solar Panel Strings, DC 30A, Φ10mm
CTF-30-10DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Compact, Space-saving, Low Cost DC Current Sensors.・Split-core type, easy to apply to existing circuit.・Easy to use by unipolar +5V power supply.・High speed responsibility – less than 10μsec. 0 rated primary current.・Suitable for monitoring solar panel strings.
-
Product
Direct Winding Transformer Monitors
-
Real time comparison of calculated and direct winding temperatures
-
Product
Computer Monitor & LCD Analyzer
MonitorTest 2.2
-
PassMark MonitorTest is a tool that allows users to investigate the quality and performance of their computer monitor or LCD flat panel screens. With more people spending more time in front of computer monitors it is important to purchase a quality monitor that will provide crisp, bright images, while reducing the strain on your eyes. The MonitorTest software generates test patterns on the screen at a variety of different resolutions and color depths to test for optimum visual performance.
-
Product
Panel for Energy Monitoring
Energy Box
-
The box allows a quick installation of the energy monitoring and remote control system Ducknet
-
Product
Network Monitor and Protocol Analyzer
Network Probe
-
Network Probe is the ultimate network monitor and protocol analyzer to monitor network traffic in real-time, and will help you find the sources of any network slow-downs in a matter of seconds. Collect and analyze data from multiple probes using the Network Probe Enterprise version for a total traffic overview of all your networks.
-
Product
16 Channel Thermocouple Monitor
SR630
-
Stanford Research Systems, Inc.
The SR630 is a 16-channel thermocouple monitor designed to read, scan, print and log temperatures or voltages. You can use any one of seven standard thermocouple types to read temperatures from -200 °C to +1700 °C.
-
Product
24/7 Monitoring
-
Provides a centralized overview of the Service Availability and Video Quality throughout all the strategic stages of the media processing & delivery flow.
-
Product
Video Quality Testing and Monitoring System
Net-Mozaic
-
The Net-MOZAIC can be used as a stand alone product or an integral part of our Net-xTVMS system. The Net-MOZAIC is normally located at the Head End with access to unencrypted TV channels. Customers define groups of 16 channels at the time. They are then decoded and analyzed for picture quality. Hundreds of channels can be analyzed this way on the round robbin.
-
Product
PDS Multibeam Survey and Processing/Charting
-
Teledyne PDS for Multibeam Surveys provides the functionality for survey planning, data acquisition, data processing, editing, volume calculations and chart production. This turnkey solution offers the surveyor and helmsman a strong tool to carry out the multibeam survey efficiently. Progress is shown real time in top, profile, and 3D views using a color-coded digital terrain model (DTM). Various filter settings can be applied to the multibeam data online, thus providing real-time data processing. Quality control displays reassure the operators that the data is of the desired quality.
-
Product
Fixed-Mount Thermal Imaging Camera for Condition Monitoring and Fire Prevention
FLIR A310 f
-
FLIR A310 f thermal camera can be installed almost anywhere to monitor the condition of your critical equipment and other valuable assets. Designed to help safeguard your plant and measure temperature differences, they allow you to see problems before they become costly failures—preventing downtime and enhancing worker safety.
-
Product
Condition Monitoring
Fluke Connect
-
Fluke is innovating industrial condition monitoring with the first system of portable sensors, a gateway and software that you can access anywhere, anytime. Each wireless sensor sends measurements every second, giving you a history of equipment performance before, during and after an event, allowing you to make preventive maintenance decisions.
-
Product
Branch Circuit Monitor
-
Multiple branches of load can be monitored togetherCan group the device as 3 phase load and single phase loadFaster communication through RS485 port (Modbus protocol)Simultaneous sampling of Volts and AmpsAccuracy Class 1.0 as per IEC 62053-21 & Class 0.5 as per IEC 62053-22 StandardsDisplays more than 25 parameters
-
Product
Monitoring
-
Configure sophisticated uptime monitoring checks without sacrificing simplicity.
-
Product
Event Monitoring System
Sigma 4
-
Sigma 4 utilizes the “Seismic Acoustic Monitoring” seismograph node. This is the most advanced, field-proven acquisition system in the world. It works seamlessly to provide the most fully integrated source control/recorder solution.*Autonomous Operation using Internal Storage*USB External Storage for Fast Data Collection*Use internal battery option or external power connection*Internal 3C geophone or external Geophone/Seismometer/Hydrophone/Microphone*Supports standard Ethernet equipment
-
Product
Wireless Hazard Monitoring
-
When it comes to hazard monitoring, we know it simply has to work. HazardPRO was designed from the ground up to provide turnkey, reliable, and consistent protection for your most valuable assets—products, facilities, and most importantly, people. Consistent operation is ensured with built-in tools such as self-diagnostics, transmission logging, and redundant radios providing you confidence that your critical processes are being monitored and logged at all times. Wireless nodes utilize temperature (bearing, ambient, and stud), RPM shaft speed, alignment, and vibration sensors. Ambient Sensors ensure bearing and alignment measurements are relative to the surrounding environment.
-
Product
SPM Monitor
CS-150
-
The CS-150 is a high-precision chemical concentration monitor designed for use with the SPM solutions used in semiconductor-manufacturing cleaning processes. Featuring fast response and a compact size, the CS-150 continually monitors the concentrations of the various components of the SPM solutions (H2SO4/H2O2/H2O) used to remove metal ions and organic substances. Feedback control based on the monitor output is used to keep the concentrations of the SPM solutions within the allowable ranges and to eliminate unnecessary replacement of chemicals.A short measuring cycle allows the accurate tracking of chemical concentrations, while the compact design facilitates integration with a cleaning device.
-
Product
Cable Plant Monitoring
-
Promptlink Communications, Inc.
Cable Plant Monitoring (CPM) is a real-time network device management tool for your DOCSIS network. CPM handles all of your DOCSIS cable modems, Wireless CMs, eMTA and Cable Modem Termination Systems (CMTS) along with monitoring fiber nodes. This allows you to readily see network problems, troubleshoot customer access issues, and easily deal with difficult management efforts, including upgrading CPE firmware on a very large scale.
-
Product
Diode Temperature Monitor
SIM922
-
Stanford Research Systems, Inc.
The SIM922 Diode Temperature Monitor and the SIM923 Platinum RTD Monitor are designed to measure four sensors simultaneously. Based on the modular SIM platform, they provide high-performance and multiple-channel capability in a small footprint.
-
Product
Vibration Monitoring System
Wireless Phantom
-
Wireless Vibration monitoring systems are today the #1 choice for continuous condition monitoring. Because of their easy installation and long life batteries as well as their affordable prices, wireless condition monitoring systems are replacing portable vibration analyzers little by little.
-
Product
Monitoring and Control System for Elevators and Escalators
-
The software package developed in the MS Visual C ++ environment has an attractive and an intuitive graphical interface. It provides for work with several groups of equipment controllers, provides advanced analysis and control capabilities (building equipment management, passenger traffic analysis, recording and playback of diagnostic information).
-
Product
HV Test System for Patient Monitors
Test System
HV test enclosure for testing medical products (patient monitors). Insulated test booth with large space for DUT.3 different test nests for adapting different devices.Displays from patient monitors are checked. For this, insulation tests and leakage current measurements must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.
-
Product
Deep Dive Application Monitoring
-
Application performance management (APM) is critical to business success today. Dynatrace automatically sees and analyzes every single user transaction, all the time. All relevant metrics, environment changes, and application deployments are shown in real-time.
-
-
Product
Frequency Monitors
FM Series
-
FM Series line-powered frequency monitors are high quality, dependable panel meters designed to continuously monitor line power frequency. Crystal reference-based for high accuracy, these 1/8 DIN/NEMA case style meters come with LED or LCD displays.
