Optical Amplifiers
Devices that boost light signal in an optical fiber network. The optical signal is amplified directly without need for electrical conversion.
-
Product
SM & MM Quad Optical Loss Test Set
KI2724-INGAAS-APC
-
A SM & MM Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber with an APC connector at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful solution to improve test flexibility and productivity.
-
Product
LXI Optical Switch - MEMS Dual 5x5 Matrix
65-280-422-M62.5
Matrix Switch Module
The 65-280-422 is a dual 5x5 fiber optic matrix plugin module designed to be fitted into a 65-200-002 Scalable Chassis. It uses multi-mode (62.5/125 μm) fiber and the optical interface is via front panel mounted LC high density connectors.
-
Product
- RS-422 to Fiber Optic Converter
Model 272A
-
FEATURES: Data Rate to 2.5 MBPS; Full Duplex TD and RD; ST Connectors; Extends RS-422 Network up to 2 km (6,600 ft). The Model 272A provides the capability of performing an interface conversion between full duplex, RS-422 signals and their equivalent for fiber optic transmission.
-
Product
Low Frequency Active Antenna And Amplifier
Type NLF-2
-
A Hot, Active, Noise Reducing Antenna System that will sit on your desk and copy 2200, 1700, and 600 through 160 Meter Experimental and Amateur Radio Signals!
-
Product
Electrical And Optical Clock Recovery
Series Oscilloscopes
-
Provide clock recovery capabilities for optical and electrical NRZ and PAM-4 signals up to 64 GBaud with jitter spectrum analysis (JSA) and integrated variable equalizers advanced features
-
Product
Overdrive Protected Amplifier
-
RF Lambda’s line of overdrive protected amplifiers incorporate a technology which eliminates the need for a limiter to protect the amplifier from damage. High input powers up to 10W can be injected in the amp without damage. Hermetically sealed options are available upon request.
-
Product
Load Cell DIN Rail Signal Amplifier
LCD20
-
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
Product
Time & Frequency Distribution Amplifiers
-
Brandywine offers a wide range of high quality, state of the art signal timing distribution amplifiers, all with very low phase noise. These precision timing signal distribution amplifiers offer a variety of time and frequency signals and interface formats including IRIG A, IRIG B, Have Quick, 1PPS, as well as low phase noise reference frequencies. All of our distribution amplifiers feature dual inputs with automatic failover and multiple independently buffered outputs.
-
Product
Broadband Amplifier
-
Toellner Electronic Instrumente GmbH
Will reproduce a wide range of signals without significant loss throughout the pass band.
-
Product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass
40-860A-012
Multiplexer Module
The 40/42-860A-012 is a PXI/PXIe single insert/bypass switch with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
High-end Cable DAC & Amplifier
Impacto essential
-
Beyerdynamic Digitalize high-end headphones.
-
Product
Highly Integrated Optical Inspection
BOA
-
BOA is a highly integrated optical inspection tool for controlling quality and increasing productivity. It comprises all the elements of an industrial machine vision system in a tiny smart camera style package.
-
Product
Silicon Optical Power Head
81620C
-
The new 81620C optical power head provides a 5 mm detector area and allows flexible placement of the remote optical power meter, which is then connected to the N7749C. The 81620C accepts parallel beams with up to 4 mm diameter, standard SM fiber and MM fiber with max. 100 μm core diameter, NA ≤ 0.3. A wide choice of adapters allows input from popular fiber connector types, bare fibers or open beams. The magnetic D-shaped adapters allow rapid removal and replacement without twisting attached fibers.
-
Product
Double IC Optic Node
OX 732
-
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics. Green Technology incorporated - Aluminium Housing for maximum heat dissipation.- Frequency 40 ~ 1000 MHz- Optical Wavelength : 1290 ~ 1600 nm- Flatness ±0.75 dB- LED Bar Display for Optic Signal Level- High C/N, CSO & CTB Characteristics- Inward Extruded Aluminium Channels for Maximum Heat Dissipation- High Voltage Surge Protection- -11 dBm Sensitivity- RF O/P at 0 dBm : 110 dBµV
-
Product
PXI Express High Speed Optical FPGA Board
HSS-8324-DSP
-
The Conduant HSS-8324 FPGA board provides a user programmable hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its two 12-lane HSS interfaces while performing complex calculations. The PXIe interface provides a theoretical maximum throughput of 8 GBps (simultaneous in and out) while each HSS port (12 lanes up to 16 Gbps per lane) supports a full duplex transfer at theoretical rates over 190 Gbps.
-
Product
Optical Light Sources
-
Wuhan Sunma Technology Co., Ltd.
Fiber Optic Light Sources are a necessity for performing fiber optic network testing to measure the fiber optical loss for both single mode fiber cable and multimode fiber cables. They are designed to cover a variety of wavelength ranges to suit all optical testing needs and usually the optical light sources are used with the fiber optic power meter to test the fiber system loss. Light sources are offered in a variety of types including LED, halogen and laser. Usually the optical light source is used with the fiber optic power meters, they act as an economic and efficient solution for the fiber optic network works. SunmaFiber offers handheld fiber optical light source and laser light source.
-
Product
Non-Contact Optical Setup for Recording the Beat of a Rotating Object
-
To develop an installation for contactless registration of beats of a rapidly rotating object. The installation should record the range and phase of the object beats simultaneously in several sections perpendicular to the axis of rotation. The results should be recorded in a file of the specified format.
-
Product
Optics Test Equipment
Software For Autocollimators And Test Telescopes
-
Optik Elektronik Gerätetechnik GmbH
Small investment - big improvement in measurement accuracy! The CROSSDETECT software is used to retrofit existing autocollimators of all types that are already equipped or can be equipped with a camera. The use of camera and software ensures that the measurement accuracy is increased by a factor of approx. 10 compared to visual measurements! The software can also be supplied complete with an autocollimator.
-
Product
AFM Optical Platform
OmegaScope
-
The OmegaScope is a state-of-the-art turn-key solution that combines Optics and ultra-resolution multi-range research AFM. The OmegaScope AFM is an advanced research instrument that provides path for researchers in spectroscopy and photonics. It is available in reflection configurations providing direct top and side optical access. The flexibility of the OmegaScope platform offer almost endless possibilities in correlation of high spatial resolution spectroscopies (Raman, Photoluminescence, Fluorescence) and AFM imaging modes.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-214-M50
Multiplexer Module
The 40/42-850A-214-M50 is a PXI/PXIe 4-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
3D Optical Surface Profiler
NewView™ 9000
-
The NewView™ 9000 3D optical surface profiler provides powerful versatility in non-contact optical surface profiling. With the system, it is easy and fast to measure a wide range of surface types, including smooth, rough, flat, sloped, and stepped. All measurements are nondestructive, fast, and require no sample preparation.
-
Product
Optical Power Meter
TM233
-
TM233 Handheld OpticPower Meter(TM233-OPM ) are mainly used for continuous optical signal power measurement，Low power microprocessor is used for control，The TM233-OPM has the advantages of fully functional and reliable performance. Widely used in optical fiber construction and maintenance, optical fiber communication, optical fiber sensing, optical CATV and other fields. Instrument mould adopts advanced cold shell molding process; beautiful and durable, Instrument mould Design meets Ergonomic requirements. The TM233-OPM uses the built-in detector, which can be protected well. With a small shape, you can choose the backlight display and automatic shutdown function, with ultra wide optical power testing range.
-
Product
Optical Return Loss Meter
ORL
-
•Four functions in one•Power meter and light source•Return loss meter and insertion loss meter•3 wavelength detection(1310/1490/1550nm)•Rugged, shock and water-proof for field use•Compact size, lightweight and cost-effective•Quick and easy to operate
-
Product
Low Phase Noise Amplifiers
-
Low Phase Noise amplifiers are critical for many applications requiring high signal integrity. This is especially relevant in instrumentation, defense, and telecommunication applications where low phase noise amplifiers are becoming increasingly important as the oscillators improve. Phase noise is described as the close-in noise to the carrier that can often appear as jitter on a clock signal. Analog Devices offers a large portfolio of low phase noise amplifiers to meet a variety of requirements in the LO network, receiver, as well as in the transmitter. Our portfolio supports a wide range of power levels and frequencies to provide the right solution for the given application.
-
Product
Amplifiers
-
low noise wideband current amplifiers (current to voltage converter) with a high gain and wide frequency band.CA261F2 and CA-461F2 are low noise voltage amplifiers which realize high precision signal processing and high density mounting by using single-in-line package which has six-surface strict shield.
-
Product
Limiting Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's limiting amplifiers use FET device with good consistency and distributed traveling wave amplifying circuit to design. Good amplitude and phase consistency characteristics can be achieved in a wide input dynamic range. It's the key component of the electronic system. Keylink's limiting amplifiers can be categorized as follows.
-
Product
Backlight Module Optical Measurement System
-
RayClouds Photoelectric Technology Co.,Ltd.
The DM series backlight module optical characteristic automatic measurement system is equipped with photometer, colorimeter and spectroradiometer to measure the luminance and chrominance, uniformity of the backlight module.
-
Product
3-Ch Sensor Amplifier
PS-1300
-
The PS-1300 3-Ch Sensor Amplifier is designed to be compact and light weight, and able to be used in combination with a tri-axial accelerometer. Each channel can also be used independently and connected with a single axis accelerometer. The PS-1300 has built-in integration function and enables to optimize the input signal to vibration data analysis devices connected.
-
Product
Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier
USBPGF-S1
-
Single Channel USB Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier for Signal Conditioning in Data Acquisition Systems. Differential or single ended input. 10Vmax Signal Input and Output with input protection up to 40V. Software-programmable instrumentation amplifier gains of 1 to 1000.
-
