Resistive Load Banks
Check power source's ability to deliver a given current and voltage at unity power factors.
See Also: Load Banks, AC Load Banks, DC Load Banks, Inductive Load Banks, Reactive Load Banks
-
Product
LED Load Simulator
63110A/ 63113A/63115A
Simulator
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is unable to simulate turn on or PWM brightness control characteristics. This may cause the LED driver to function improperly or trigger it’s protection circuits. These testing requirements can be achieved when using a LEDs as a load; however, issues regarding the LED aging as well as different LED drivers may require different types of LEDs or a number of LEDs. This makes it inconvenient for mass production testing.
-
Product
Winding Resistance Meter 100Amps, 3 Channels
WR100-13R
-
Raytech Digital Winding Resistance meter WR100-13R is the enhanced version winding resistance system with a most advanced demagnetizing circuit as a rack version. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
-
Product
Motive Power Load Banks
-
The only way to be certain that your stationary batteries will perform to specification is to test the batteries’ capacity with a DC load bank / portable battery discharge tester.
-
Product
PXI 8 Banks of 8 Chan 1 Pole MUX
40-657-001-8/8/1
Multiplexer Module
40-657 High Density Power Multiplexer Modules are available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
Product
Non-contact Sheet Resistance /resistivity Measurement Instrument
EC-80
-
*Easy operation and compact design*Auto-measurement start by inserting a wafer under the probe*Easy set up to measurement condition by JOG dial*5 types of model for each measuring range
-
-
Product
PXI MUX 4 Bank, 16 Channel Screened 1 Pole
40-610-021-S-4/16/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Hand Cranked Analog Insulation Resistance Tester
IRT20
-
UEi Test & Measurement Instruments
The IRT20 is a Hand-cranked Insulation Resistance Tester. With a insulation resistance range of 0.1 to 1000MΩ, 250, 500 and 1000V output ranges and accurate to with in one division. It is in a sealed, water resistant, rugged metal housing and is backed by a 1-Year limited warranty.
-
Product
New 12v Battery Load Tester
-
Hangzhou Xun Anda Electrical Co., Ltd.
battery maximum capacity: 120Ah or 1200CCA(SAE)voltage test range: 7-15VDCoperating voltage: 7-15VDC , storage battery power suppliedmaximum power dissipation: 0.5W aroundoperating temprature: -10°C~50°C;operating humidity: 30%~90% (without condensation)display modes four super bright nixie tube with 0.56 inch ,four different color Led indicator lightkeying: three keying total for using related operation
-
Product
Shear Beam Load Cell
SB-1.0
-
The Shear Beam Load Cell SB-1.0 is a single point weighing device, suitable for use in multiple applications.
-
Product
Hipot Current Calibration Load Resistors
HPRS-HIPOT-LOAD
-
The IET HPRS-Hipot-Load is an excellent replacement for the Fluke 5320A-Load Hipot current calibration load resistors. The IET high power resistive load can be used with the Fluke 5320A Multifunction Electrical Tester Calibrator or standalone. It provides a high power and high voltage load to various hipot tester to create the leakage current needed to calibrate various manufactures hipot testers.
-
Product
Ground Resistance Tester
2521
-
Shenzhen Chuangxin Instruments Co., Ltd.
High measuring accuracy, high speed, easy to use, especially suitable for using in laboratory and automatic testing line. Test current AC / 5 ~ 30 (a), resistance Ω (0 ~ 600 m), time (1 ~ 99 s) shows at the same time. Test time can be arbitrary setted. Test alarm value can be arbitrary set up. Pass/fail sound and light alarm.
-
Product
AC & DC Action Load Test
-
Shanghai Guantu Technology Co., Ltd.
1. AC action load power supplyVoltage range: 0~1000V;Current range: 5A ~ 100A.2. DC action load power supplyVoltage range: 0~1500V;Current range: 5A ~ 100A.
-
Product
Load Monitoring Units (LMUs)
-
Magtrol's Load Monitoring Units are used for measuring load, force and weight from signals generated by strain gauge transducers. Specifically designed for use with Magtrol's Load Measuring Pins and Load-Force-Weight Sensors, the LMU Series provides excitation voltage while conditioning the bridge output signal. Each unit contains DIP-switches and jumpers for greater flexibility and complete adaptability
-
Product
Portable Winding Resistance Tester
-
1. Handheld winding resistance meter2. Conversion function for standard temperature resistance.3. 500 test data can be saved and download by flash disk.4. Temperature testing function.
-
Product
Electronic Loads
-
We offer devices that provide wide-ranging AC, DC, and AC/DC electronic load capabilities to meet a variety of telecommunications, manufacturing, utility, and other applications. Our models accurately simulate the operational load that equipment.
-
Product
Handheld Contact Resistance Tester
-
Weshine Electric Manufacturing Co., Ltd
The hand-held Circuit resistance tester is an innovative product. The product is compact, hand-held operation, battery power supply, easy to carry. The product is mainly used in the measurement of contact resistance and other micro-Euclidean resistance of switch contacts. The test speed is fast and the accuracy is high.
-
Product
Insulation Resistance Tester
-
Aarohi Embedded Systems Pvt. Ltd
Aarohi make device enable us to measure electrical leakage in wire, results are very reliable as we shall be passing electric current through device while we are testing. The equipment basically uses for verifying the electrical insulation level of any device such as motors, cables, generators, windings, etc.
-
Product
AC Load Bank
XL750-XL800 Series
-
Mosebach Manufacturing Company
The XL750-XL800 Series load banks offer you a continuous load at various voltages in a compact, lightweight enclosure.
-
Product
Load Cell Power Supply Module
MODEL PSM-F10
-
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
Product
Metal Foil Llow Resistance Chip Resistor
MFR (Metal foil)
-
*Low Resistance / TCR / EMF 9only FOR MnCu) / Inductance*Excellent long term stability*RoHS compliant and halogen free.*Lead free.* High precision current sensing and voltage division.
-
Product
150~300W DC Electronic Loads
JT631 Series
-
Nanjing Jartul Electronic Co., Ltd
JT631 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT631 series load very suitable for testing power supply when produced in large quantity. Besides, JT631 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT631 series load satisfing most of R&D requirements. Moreover, JT631 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
Product
Load Cells
-
is a transducer that is used to create an electrical signal whose magnitude is directly proportional to the force being measured.
-
Product
Load Testing for Evolved Packet Core (ePC/VePC)
Flare
-
Linkbit Flare is designed for load testing of Evolved Packet Core (ePC) networks, and the upcoming VePC deployments. It is based on the technology initially develped for Linkbit functional testers, and as a result is extremely flexible.
-
-
Product
Load Cell Indicators
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicator will need to be mounted in to a case or control rack for safe use.
-
Product
Battery Load Tester
Battery Beak
-
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
Product
Load Cell Indicator
9840
-
The 9840 is suitable for use in calibration labs, field service, or anywhere high accuracy is important. Features include a bipolar 6-digit 2-line display, remote sense, low noise, 22-bit resolution, USB port with RS232 communication, mV/V calibration and the ability to store up to 25 different sensors. 6-point linearization, unit conversion, front-panel tare. Self calibration via TEDS Plug & Play ready IEEE1451.4 compliance.
-
Product
Single-Phase Transformer Winding Resistance Meters
RMO-TW Series
-
RMO-TW series is perfect for winding resistance measurements of inductive objects. It is ideal for testing transformer windings (power transformers, distribution, autotransformers) and for on-load tap changer verification. In addition, any RMO-TW transformer ohmmeter & tap changer analyzer can also perform transformer demagnetization.The series contains 4 models, with maximal test currents from 10 A (RMO10TW) to 50 A (RMO50TW). They are fitted in a portable and lightweight metal housing.All transformer ohmmeters from RMO-TW series generate a true DC ripple-free current with automatically regulated measurement and discharging circuit. The injection of current and discharge of energy from the test object are automatically regulated.Three independent channels enable testing of three windings in series. Consequently, this enables measurements of winding resistance in every tap position of an on-load tap changer without discharging between the tests.DV-Win software enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test. Finally, a user can export all results in the form of a report.
