Showing results: 991 - 1005 of 1255 items found.
-
PE42512 -
pSemi Corp.
The PE42512 is a HaRP™ technology-enhanced absorptive SP12T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42512 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
PE42562 -
pSemi Corp.
The PE42562 is a HaRP™ technology-enhanced absorptive SP6T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42562 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
PE42582 -
pSemi Corp.
The PE42582 is a HaRP™ technology-enhanced absorptive SP8T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42582 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
400C Series -
CH Instruments, Inc.
The quartz crystal microbalance (QCM) is a variant of acoustic wave microsensors that are capable of ultrasensitive mass measurements. Under favorable conditions, a typical QCM can measure a mass change of 0.1-1 ng/cm2. QCM oscillates in a mechanically resonant shear mode under the influence of a high frequency AC electric field which is applied across the thickness of the crystal. Figure 1b below shows an edge view of a QCM crystal undergoing oscillatory shear distortion. The central portions of the top and bottom of the crystal are coated with a typically disk-shaped thin metal film (e.g., gold).
-
Quantic PMI
PMI's line of Bi-Phase Modulators includes a comprehensive selection of different models which cover broad octave frequency bands ranging from 0.5 to 40 GHz. Bi-phase modulators take a TTL level digital bits stream that’s encoded onto the RF carrier using 2 Phase Shift Keying (2PSK) modulation, where the 2 phases are separated by 180º. This performance is desirable in communications systems, microwave radio, radar, high data rate test & measurement, serial data transmission, base station infrastructure, and other industrial and military applications.
-
MISS -
BioAge s.r.l.
The Micro Smart System is one of the many autonomous systems with very low consumption designed by BioAge. The system is characterized by autonomous operation with very low energy consumption thanks to its operation in "Energy Harvesting" which allows to exploit the power supply from a micro solar panel with which each sensor is equipped. Furthermore, these systems are equipped with radio frequency communication able to remotely transmit the information acquired by the sensors on board, it is therefore possible to create a network of sensors, operating autonomously and with a very high autonomy thanks to solar energy.
-
PP007-WS-1 -
Teledyne LeCroy
The PP007 embodies leading technology in passive probe design. The small probe is optimized for maximum waveform fidelity, including high frequency signal components, in a rugged probe suitable for every day.The sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head. The tip does not slip off the object being probed—important when probing small geometry surface-mounted components. Probing dense circuits is easier with the small 2.5 mm ground sleeve, which provides much better visibility than 5 mm and 3.5 mm probes.
-
PP007-WR-1 -
Teledyne LeCroy
The PP007 embodies leading technology in passive probe design. The small probe is optimized for maximum waveform fidelity, including high frequency signal components, in a rugged probe suitable for every day.The sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head. The tip does not slip off the object being probed—important when probing small geometry surface-mounted components. Probing dense circuits is easier with the small 2.5 mm ground sleeve, which provides much better visibility than 5 mm and 3.5 mm probes.
-
Apex Technologies
The new AP6051A stand-alone benchtop fiber-coupled polarimeter enables real time monitoring of the SOP, DOP, and power of a light signal in fiber. It can display SOP data information either on a Poincaré sphere, a Jones diagram or on a virtual oscilloscope. Covering the operating wavelength range from 1520 to 1610nm, it offers excellent performance, fast sampling rate, high SOP accuracy, and wide dynamic input optical power range. Optionally, it can be used in combination with an internal Optical Filter to measure the SOP as a function of frequency. Intuitive software and touch screen allows an easy manipulation of the device.
-
LPT-3000RX4 -
LP Technologies
Latest DSP Technology; 9 kHz to 3 GHz Frequency Range; External 10 MHz Reference; 17 RBW filters Down to 1 Hz; 17 VBW filters Down to 1 Hz; > 88 dBm Dynamic Range; High Definition Spectrum Trace; 55 dBm Input Port Isolation; 50 dBm input attenuator; 0.5 millisecond Port Switch Speed; Available in 4, 8 or 16 RF inputs; Optional Internal Carrier Identification CID module; Optional Internal Down Converter modules
-
SA-S -
EMC Test Design, LLC
RF Frequency Range: 1 Hz to 4.2 GHz. Low noise amplifier available above 500 KHz. Wide dynamic range: -151 dBm to +10 dBm. Resolution bandwidths (RBW) of 0.1 Hz to 250 KHz and 5 MHz. Includes a High Dynamic Range Measuring Receiver. 0.25 dB relative accuracy. 0 dBm to -125 dBm, 150 KHz to 1 GHz. 0 dBm to -115 dBm, 1 GHz to 4.4 GHz. Adjustable digital audio filters. Accurate AM and FM measurements
-
Fivestar HV Testing Equipment Co., Ltd.
FSHV offers three different types of AC voltage test systems, the conventional type is AC test transformer design, mainly for testing objects of medium & low capacitance products, particularly for tests requiring stable voltage even if the load changes under voltage (corona, wet & pollution tests) or when the load is inductive (like inductive voltage transformers). Another is AC resonant test systems, according to series resonance circuit XL=XC (2πfL=1/2πfC), by setting F frequency of power supply or L inductance of reactor, generate a pure sinusoidal waveform of the test voltage, and the required input power is only 1/Q. Variable frequency type operates in a frequency range from 20Hz to 300Hz, ideal for field commissioning test of power cables and GIS/GIL. Variable inductance type outputs continuous AC voltage of power frequency (50/60Hz), mainly for factory testing of high and ultra-high voltage cables, power transformers, GIS, etc.
-
Pickering Interfaces Ltd.
Pickering's RF SPDT PXI Switch Modules are capable of providing economic switching for frequencies up to 6 GHz. Our other PXI RF options include RF matrices and RF multiplexers. For higher frequency applications or applications requiring high performance levels, please take a look at our microwave switching modules.
-
MicroContact AG
With the micro probes and the fine-pitch adapters used on them, you are able to contact the finest test structures. E-tests, functional tests, IC tests or high-current tests are made to be affordable, efficient and with a short cycle time. With the integration of HF adapters we also enable the double-sided testing of HF substrates up to high frequency ranges.
-
Pasternack Enterprises, Inc.
Pasternack SMP connector (sub-miniature push-on connectors) category contains mostly RoHS and REACH compliant product varieties. The SMP connector category includes dozens of configurations including coaxial sub-miniature push-on connectors, PCB mounted, non-sealed and hermetically sealed terminals and shrouds. Our subminiature push-on SMP connectors are built to precise microwave and RF industry specifications and are part of over 40,000 in-stock RF products. Connectors in SMP series from Pasternack are manufactured in male or female gender with a 50 Ohm impedance. Pasternack's SMP subminiature connector are available in straight or right angle versions as well as bulkhead or mount-less options. These connector designs include solder or solder/solder attachment methods. Pasternack’s SMP connectors are miniaturized push-on interconnects commonly used in high density, blind-mate systems that can operate up to 40 GHz. Standard sub-miniature push on connector items are offered in a high frequency 40 GHz version as well as a low frequency 8 GHz version and are also available in smooth bore, limited detent and full detent styles. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMP connector series is in-stock. Not just in stock, these subminiature push on connectors will also ship the same day as they are purchased.
