PMC Adapters
Computer boards that translate the data from the PMC bus to another bus and vice versa. They are used to connect two incompatible buses. (globalspec.com)
-
Product
Rugged Embedded MIL-STD-1553Conduction Cooled PMC Card
AMCE1553-x
-
Rugged embedded MIL-STD-1553 conduction cooled PMC card.
-
Product
FAX Adapters
-
The VoIP ATA for FAX is a powerful, cost-effective solution for customers who need to securely send and receive faxes using a traditional, analog fax machine often needed for legal and privacy compliance such as HIPPA or FERPA.
-
Product
VME Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
AVC-2
-
VME64x (6U) generic carrier card for PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
-
Product
Premium Microwave Cables And Adapters
-
Thorlabs' Microwave Cables and Adapter Cables are flexible, high-performance, coaxial cable assemblies designed for use out to 50 GHz, depending on connector type (see the image to the right). The design gives these cables flexibility while maintaining optimal performance. They exhibit low VSWRs (Voltage Standing Wave Ratios) over the usable frequency range, as well as low insertion losses (see the Specs tab). These cables are each tested to ensure performance.
-
Product
PMC SpaceWire
-
PMC SpaceWire implements SpaceWire in a convenient PMC format. With PMC you can install the adapter into PCI [PCIBPMC], cPCI [cPCI2PMC], or processor board pmc slots. The SpaceWire specification calls for LVDS signaling and a specific 9 pin micro-D connector. You can connect the PMC-SpaceWire to other SpaceWire compliant devices without electrical interface issues
-
Product
FMC, XMC & PMC
-
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
Product
12C Adapter Slave
LAN I2C adapter MS
-
*No driver necessary*Integration of communication via DLL and TCP / IP & UDP protocol possible*Open interface description enables communication without a DLL*Supports TCP / IP, UDP and DHCP
-
Product
cPCI to PMC Compatible Adapter/Carrier
cPCIBPMC6UET
-
cPCIBPMC6UET ( cPCI to PMC ) adapter / carrier converter card provides the ability to install up to two PMC cards into a standard cPCI slot. cPCIBPMC6UET has two PMC card slots mounted to a universal voltage 6U 4HP cPCI card.
-
Product
Coaxial Waveguide Adapter, 2.4 mm (m), 26.5 to 50 GHz
R281B
-
The Keysight R281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
100-FX Fiber Optic Ethernet PMC
3006
-
The Ethernet 100-FX Adapter provides a single port Ethernet connection using Fiber Optic media. An AMD 79C973 Ethernet controller provides a integrated link and physical layer for operating at 100 Mb/s. The Fiber Optic connector used on the board can be either the ?SC Duplex? style, or the ?ST RX/TX? style and is identified by the Technobox Part Number.
-
Product
LC Adapters
FY3
-
FIBERYO LC Adapters are available in simplex and duplex configurations. They feature self-adjusting panel latches as well as a choice of mounting orientations and labeled polarity.
-
Product
RF Adapters
SMP Adapters
-
A subminiature interface in the same scale as MMCX connectors but offers a frequency range of DC to 40 GHz.
-
Product
Test Adapter
-
Development of a 12-way test and programming adapter from Toptest for ?? The Dash ?? from Bragi, a wireless, intelligent earphone with communication and sensor technology. With the first version of the test adapter, only a purely sequential testing was possible due to the interdependencies of the tests. In version 3.0, the now autonomous tests were brought into a parallel TestStand sequence. In addition, individual sockets were prioritized in order to optimally use the hardware resources. This resulted in a time advantage of 80% compared to the initial situation.
-
Product
Adapter, 1.0 mm (f) to 1.0 mm (f), DC to 110 GHz
11920B
-
The Keysight 11920B precision 1.0 millimeter waveguide-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms and frequency range from dc to 110 GHz.
-
Product
XMC-to-PCI Express Adapter
4821
-
The XMC2PCE is a passive 8X XMC to PCI express carrier card which permits the use of XMC cards in PC style PCI express 1X, 2X, 4X, 8X or 16X motherboard slots.
-
Product
Flexible 32-bit PCI to x1 PCI Express Adapter
SKU-049-0X
-
The Flexible 32-bit PCI to x1 PCI Express Adapter (Adapter) was designed to expand the 32-bit PCI bus into an x1 PCI Express bus. It allows you to connect the x1 PCI Express expansion board to the motherboard PCI connectorThe Adapter includes an x1 PCI Express adapter board, 32-bit PCI host board and PCI Express Flat cable.
-
-
Product
Manual Test Adapters
-
Manual test adapters (MA) from INGUN are available in several series and series, which differ in terms of use, maximum permitted contact force, parallel stroke, size and service life.
-
Product
AC Current Clamp Adapter
LAD-1100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Selectable measuring range 30mA~30A with CT ratio 10:1 and 30A~3000A with CT ratio 100:1.●φ110mm CT window, possible to measure from leakage to big current up to 3000A.
-
Product
Carbon Monoxide Detector Adapter
COA1
-
UEi Test & Measurement Instruments
The COA1 Carbon Monoxide Adapter plugs into compatible iOS® or Android™ mobile device to measure carbon monoxide levels.
-
Product
ACC-188 Synchronous Serial Radio Adapter
-
The ACC-188 synchronous serial radio adapter is interoperable among various tactical radio brands and models used by the defense community. The ACC-188 works with any radio that has a synchronous serial communication port using MIL-STD-188-184 and enables the tactical radios to send data such as GPS maps, images, coordinates, and IM-type communications.
-
-
Product
Adapter, 1.0 mm (f) to 2.4 mm (f), DC to 50 GHz
11922B
-
The Keysight 11922B precision 2.4 millimeter coax in adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and a frequency range from dc to 50 GHz.
-
Product
Adapter, 1.0 mm (m) to 2.4 mm (f), DC to 50 GHz
11922C
-
The Keysight 11922C precision 2.4 millimeter coax in adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and a frequency range from dc to 50 GHz.
-
Product
Connector PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x96 Male SCSI
510150128
PCB Adapter
Connector PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x96 Male SCSI
-
Product
Flexible 32-bit PCI to MiniPCI Express Adapter
SKU-057-0X
-
The Flexible 32-bit PCI to MiniPCI Express Adapter (Adapter) was designed to convert the 32-bit PCI bus into a MiniPCI Express bus. It allows you to connect the MiniPCI Express expansion board to the motherboard PCI connector.The Adapter includes a MiniPCI Express adapter board (downstream), 32-bit PCI host board and PCI Express flat cable.
-
Product
Local DVB-T2 Adapter
T2 Edge DTH
-
T2Edge DTH is ENENSYS local DVB-T2 adapter of the OneBeam DVB-T2 solution. Running on the transmission site prior to the DVB-T2 transmitter, the T2Edge DTH aims at receiving a DTH stream to build a new DVB-T2 multiplex. It selects the services from the DTH stream and generates a T2-MI stream. The T2EdgeDTH performs an advanced PSI/SI processing to update PSI/SI information related to the filtered services.
-
-
Product
ProBus Probe Adapter for TekProbe-BNC Probes
TPA10
-
- Allows TekProbe interface level II probes to work with any ProBus-equipped Teledyne LeCroy oscilloscope- Automatic probe detection- Provides all necessary power and offset control to the attached probe- Supports probes up to 4 GHz- Easy firmware updates- Wide variety of probes supported including: Preamplifiers, Current Probes, Single-Ended Active Probes and Differential Active Probes
