V.35
-
Product
PXI/PXIe High Density Digital Input Module, 128-Channel, 50V
42-414-101
Digital Input Module
The 40-414-101 (PXI) and 42-414-101 (PXIe) are 128-channel digital input modules with 50 V inputs and provide a convenientway of determining the status of input lines by comparing the input voltage with two threshold voltages - quicklyestablishing if the input is low, high or in an intermediate logic state.
-
Product
IO60-DIO48 Module
IO60-DIO48
Module
WINSYSTEMS’ IO60-DIO48 Module adds GPIO to embedded systems with IO60 expansion featuring 48 GPIO (General Purpose Input-Output) tolerant to 30 V DC. The SPI interface is implemented through the MACH XO2 SPI-slave EFB (Embedded Function Block) interface. Each bit of each port is implemented as a bi-directional tristate driver. Each bit of each port can also be configured and enabled to detect rising and/or falling edge events and generate a system interrupt.
-
Product
Advanced Power System - Dynamic DC Power Supply, 20 V, 50 A, 1000 W
N7951A
DC Power Supply
The N7900 Series dynamic DC power supplies are designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
Product
Compact Low-Frequency Control Element
900-LFC
-
The 900-LFC Low-Frequency Control Element extends the response of mid-sized P.A. systems to 35 Hz, revealing the nuances of your mix, down to the deepest bass with total accuracy.
-
Product
JR-1
12820
-
• 35 Amp relay [@ 24VDC max. or @ 48VAC max.]• Crystal controlled timing• Rechargeable battery• Immediate or delayed interruption operation• Low battery indicator• Countdown and relay status indicators• On and off cycle times up to 999.9 seconds• Synchronized operation with any number of JR-1's and JR-2's
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-01
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
Photometric Radiometric Transmitters
HD2021T6 / HD2021T7
-
The transmitters allow converting the photometric quantity “equivalent veiling luminance” – HD2021T7 – or a photometric quantity Luminance (cd/m2) – HD2021T6 – into a current (4…20 mA) or a voltage (0…10 V) signal according to the version chosen. If the acquisition station is far from the probe (>50m), it is necessary to use the current output version.The probe is used for the control of street lighting, in particular, the measurement of equivalent veiling luminance is essential to determine the threshold luminance at the entrance of the tunnels (UNI 11095:2011).
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 1 kV Isolation
43-752A-103
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
20 Bit Dual-Channel Reference Source
DRS20
-
The DRS20 is a dual-channel reference source offering ultra high precision and stability and provides a +/-10 V output. The output current can be up to 10 mA and the 4 wire connection provides a 1 µV/mA load regulation. The high precision and stability is achieved by using a temperature controlled voltage reference.
-
Product
AC / DC - Power Supplies
-
The spectrum of DC power supplies ranges from simple power adapters with only one output voltage to complex controllable power sources. Power adapters, often also called plug-in mains adapters, are mainly used for small electrical appliances (such as telephones, strings of light, notebooks, etc.) in private households. They are included in the scope of delivery of the product and only serve to supply power with a defined output voltage of 6 V or 12 V, for example. The output power is usually limited to < 200 W due to the simple design.
-
Product
Multifunction Meter for Electrical Installations
AMPI-530
-
Measurement of short-circuit loop ; Testing of differential, general and selective protections for differential current ; Measurement of insulation resistance ; Up to 10GΩ ; Voltages: 50 V, 100 V, 250 V, 500 V, 1000 V ; Measurement of earth resistance ; Bi-directional continuity test on PE cables, phase sequence ; Measurement and recording of voltage, frequency, alternating current, cosϕ, power, harmonics and THD
-
Product
Ku Band Gain Control Amplifier
-
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
Product
8 SE Or 4 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-8-4
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
E1 Testers
-
GAOTek provides a large collection of high quality, affordable E1 testers that are specially manufactured to speed up the ethernet maintenance time and work efficiency for sale to the United States, Canada and Globally. These devices consist of PING, router trace, a port location tool, a loop-back tool and offers a variety of Ethernet diagnostic functions. These E1 Ethernet test instruments are all incorporated with test tools for E1, V port, and Gigabit Ethernet link repairs, and failure diagnosis. E1 Ethernet testing devices are user-friendly, can be used in Ethernet cable tests, flux error code tests, connectivity performance, traffic testing, ethernet wire testing, and bandwidth verification. As these devices help in measuring and proving performance for criteria Ethernet networks they are commonly used in the RFC2544 performance test.
-
Product
Bench Power Supply, Single, Fixed, 1 Output, 13.8 V, 25 A
72-8115
-
25 Amp Current Switch Mode Power Supply Efficient switch mode power supply features a very compact footprint and lightweight design. It is perfect for telecommunications equipment, two-way radio (including HF) and audio equipment including high power autosound and multimedia systems.
-
Product
PXIe-4300, 16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module
781337-01
Analog Input Module
16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module—The PXIe‑4300 provides integrated data acquisition and signal conditioning for high-voltage measurements. It provides increased accuracy, simultaneous sampling, and synchronization features for scalable measurement systems. The PXIe‑4300 includes 300 Vrms channel‑to‑channel CAT II isolation and 3,300 Vrms channel‑to‑earth 5 second withstand isolation to protect users and equipment from hazardous voltages. This module offers programmable lowpass filtering, DC input coupling, and two PFI lines for digital input triggering. The included NI‑DAQmx driver simplifies hardware and configuration and measurement.
-
Product
FC Impedance Meters
-
designed for testing of the fuel cell with the small current (5 A or less), and not only the current-voltage characteristic test, the KFM2005 can easily measure for the impedance of a fuel cell using the AC impedance method, and the Cole-Cole plot. Using the measurement data of the Cole-cole plot, it is possible to calculate the circuit constant of the approximate equivalent circuit of the fuel cell. The built-in DC load (60W) is capable to operate from 0 V, and it can perform the test for the fuel cell up to 20V and 5A.
-
Product
Standard 1.00 (28.00) - 2.75 (78.00) Non Replaceable General Purpose Probe
E-S-R
General Purpose Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 30Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 65Full Travel (mm): 1.65Recommended Travel (mil): 43Recommended Travel (mm): 1.09Overall Length (mil): 495Overall Length (mm): 12.57Rec. Mounting Hole Size (mil): 67Rec. Mounting Hole Size (mm): 1.70Recommended Drill Size: #51Overall Length Remark: Overall length for E-S-V and E-S-W is .540 (13.72)
-
Product
DC Power Supply, 6 V, 5 A, 30 W
E36102B
DC Power Supply
The Keysight E36102B is an accurate, 6 V, 5 A, 30 W compact power supply for your bench or system.
-
Product
Turns Ratio Testers
TRT Standard Series
-
When it comes to choosing a transformer turns ratio tester, TRT Standard series offers some of the most advanced instruments with LCD display out in the market. Each model measures transformer excitation current and phase shift performs automatic vector group detection and magnetic balance on three-phase transformers and three-phase autotransformers. Furthermore, they have a built-in true three-phase power source. Because of that, TRT Standard instruments can test transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.The instruments can output test voltages from 1 V AC to 250 V AC, depending on the chosen model. High test voltage of 250 V AC provides more accurate turns ratio testing compared to other turns ratio testers on the market and extremely low test voltage of 1 V AC enables turns ratio verification of current transformers.TRT Standard series consists of:TRT03 Models (TRT03A, TRT03B, TRT03C) – single-phase voltage up to 100 VTRT3x Models (TRT30A, TRT30B, TRT30C, TRT33A, TRT33B, TRT33C) – single and true three-phase voltage up to 100 VTRT63 Models (TRT63A, TRT63B, TRT63C) – single and true three-phase voltage up to 250 VMore about models differences can be found under the downloads tab, in brochures and comparison sheets.A user can create test templates using the DV Win software and store them in the PC’s memory for later use when in the field.TRT Standard series models have a built-in tap changer control unit. Consequently, it enables remote control of an on-load tap changer (OLTC) directly from the tester. In order to make the most out of this feature, the DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions and saving results. This option, especially in combination with test templates, significantly facilitates and shortens the turns ratio testing time.
-
Product
Digital Insulation Multimeter Tester 1 KV
MIRT-61
-
The Motwane Manufacturing Company
The MOTWANE multipurpose tester Model MIRT-61 is a Versatile, battery operated Digital insulation tester with true RMS industrial grade multimeter features best suited for industrial preventive maintenance. With test voltage range up to 1 KV , highest insulation resistance range of 6G Ohm and multi featured function of RMS multimeter (i.e. AC/DC 1000 V) ; makes it a superior offering for Industry and Service segment. It is designed predominantly for low voltage insulation resistance testing in maintenance and services, which involves the applications like Cables/Wires, Rotating Machines, LT transformers, Switchgears and Industrial installations. It is designed to suit the extreme environment conditions. Save your operating cost and test more with this single box design rather buying two different products.
-
Product
PXI-4110, 3-Channel, 20 V, 1 A, 9 W, PXI Programmable Power Supply
779647-10
Programmable Power Supply
3-Channel, 20 V, 1 A PXI Programmable Power Supply—The PXI‑4110 is a programmable DC power supply. It is an excellent general-purpose, single-quadrant power supply for design validation and manufacturing test applications. The PXI‑4110 has two isolated and a single non-isolated supply channel, all capable of generating up to 1 A per channel. You can program the voltage setpoint and current limit as well as the voltage and current readback/measurement functionality. You can also combine channels for higher voltage or current.
-
Product
Amplifier Module
LNAM-FBX
-
Ultra-low-noise voltage amplifier module (LNAM) with ac coupled FET input allowing measurements between 1 Hz and 20 MHz. High gain precision and low distortion are achieved by using internal negative feedback and >1000 V/µs output stages.
-
Product
2 in 1 Power Meter
FiberPal OT-2000-V
-
The FTTx Wide Band VFL Meter, OT-2000-V, is a powerful optical measuring tool which can be used in various optical fiber systems and applications, especially in FTTx field installation and maintenance. With 850, 1310, 1490, 1550 nm calibration wavelength, it is ideal for both single mode and multimode fiber field installation and maintenance. The additional 650nm light source makes for a convenient, easy to use yet powerful device to check for broken fibers as well.
-
Product
Bench Power Supply, Calibrated, Adjustable, 1 Output, 0 V, 30 V, 0 A, 5 A
72-2690 CAL
-
The 72-2690 CAL from Tenma is a single channel adjustable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has complete digital control, intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +20mV (voltage), ≤0.5% +10mA (current).
-
Product
DC/DC Converter 150 W
CQB150W-110S48
-
DC/DC converter with 150 W from Cincon | input ranges 43 - 160 VDC | output 48 V | operates in temperature from -40 to +105 °C | according to EN45545-2 fire and smoke
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 750 V Isolation
43-752A-003
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Solder Cup Connector Kit
Y1141A
D-Sub Male Connector
Used to build custom cables for 34951, 34952 – 50-pin Dsub male – 125 V.
-
Product
NI-9221, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
779373-01
Voltage Input Module
±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the NI‑9221: a 36‑position spring‑terminal connector and a 37-position D‑SUB connector.
-
Product
PXIe-4141, 4-Channel, ±10 V, 100 mA, Precision PXI Source Measure Unit
781743-01
Source Measure Unit
PXIe, 4-Channel, ±10 V, 100 mA, Precision PXI Source Measure Unit - The PXIe-4141 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4 wire) sensing for accurate measurements. The fast sample rate of the PXIe-4141 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4141 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
