Earth Testers
See Also: Earth Resistance Testers
-
Product
Flight Simulator Tester
-
Excalibur’s Flight-Sim Tester is a hardware and software solution for enabling near-real flight testing scenarios for airborne system testing (avionics testing).
-
Product
Mixed Signal Automated Tester
MSAT
-
Whether you are testing radar systems for the Department of Defense (DoD), or the next actuator circuit card for aircraft landing systems, ARC’s Mixed Signal Automated Tester (MSAT) offers flexible automated testing capabilities for nearly every budget.
-
Product
ADB Bearing Sensor Tester
-
The ADB Sensor Tester (ADBT) has been designed to test 4B adjustable depth bearing (ADB) style temperature sensors in the field. During planned maintenance or periodic testing, the ADBT can be used as a diagnostic tool to verify the alarm and shutdown sequences of the control unit are functioning as expected. The unit operates in two testing modes, direct (heated) and indirect (simulated).
-
Product
Flexible AC/DC Current Tester
FCM-100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Bending free flexible clamp sensor *Wide measuring ranges (AC/DC 0.001A～2500A)*Easy accessibility to the hard to clamp object*Big CT window (φ200mm)
-
Product
Shock Absorber Tester
-
Maschinenbau Haldenwang GmbH & Co. KG.
Display on LON analog displays with theEvaluation in "Lehr''s damping factor" or damping ratio "D"Fully automatic testAutomatic test start after bilateral plate load of more than 60kgFrequency controlled drive excitation by electric motors to determine the maximum vibration amplitude with subsequent evaluation of the axle dampingrunning underbody as self-supporting frame constructionParallelogram guided test plates, thus no fixed wheel contact requiredgalvanized version
-
Product
Ball Rebound Resilience Tester
UI-FT95
-
Ball Rebound Resilience Tester is used to test foam resilience by vertically dropping a steel ball on foam from required height.
-
Product
Electrical Tester
T6-1000
-
The Fluke T6-1000 Electrical Tester with FieldSense™ technology lets you quickly, safely take True rms voltage and current measurements without test leads.
-
Product
Chassis Dynamometer Smoke Testers
-
A chassis dynamometer smoke tester (CDST) is used to test diesel emissions when the engine is under load. This is of course a much more realistic test than the commonly used free acceleration test. It is also better for the diesel engine.During a CDST test an automatic test cycle is performed, whereby the emission is measured at different engine loads. The monitor shows checks and actions to perform before the test, shows real-time measuring data and instructions for the driver during the test, and the end results after the test.
-
Product
Cable ID & PoE Tester
PK-170 INNOTESTER PRO
-
INNOTESTER PRO combines the functions of a smart cable tester, network tester, port identifier and organizer with the capability to identify up to 100 cables run at a time, and 8 Test + ID remotes allows one person to test 8 cables run up to 600 meters. Tone mode, transmits 2 powerful tones for tracing inactive and active network cables on a Switch or HUB. More effectively tracing at patch panel, termination blocks or hidden within bundles.
-
Product
Transmission Line Testers
-
GAOTek provides affordable, safe and reliable transmission line testers, digital clamp meters and power meters for sale to the United States, Canada and Globally. A transmission line is a specialized cable designed to conduct alternative current of radio frequency. Transmission lines are used for connecting radio transmitters and receivers with their antenna to distribute signals.
-
Product
HDD Motor Testers
BK8015/BK8015A
-
The BK8015 HDD Mechanical Specifications Tester and the BK8015A HDD Circuit Specifications Tester were designed and manufactured by BaKo to test HDD motors as they come off the assembly line. The two machines are complementary, and were designed to test a complete set of HDD motor characteristics.
-
Product
LATCH UP Tester
-
Tokyo Electronics Trading Co., Ltd.
The purpose of Latch-up testing on your components is to verify their robustness against overvoltage/ overcurrent events during their operation.
-
Product
Comparative Dissolution Tester
CD14 Comparative Dissolution Tester
-
The Teledyne LABS 14-vessel CD14 Comparative Dissolution Tester runs two methods simultaneously or independently—ideal for bioequivalence studies of generic vs. innovator drug formulations. The 14 stirring positions allow for 6+1 or 12+2 configurations for improved workload efficiency in R&D, formulations, QC, and stability-test labs. With digital temperature probes at 12 positions the CD14 comparative dissolution tester is able to test two different formulations with separate settings for every parameter under the same temperature conditions.
-
Product
CELL TESTER
SPOTLIGHT
-
SpotLIGHT was designed to minimize maintenance and to significantly reduce downtime. The lifecycle of its contacting system is longer than that of standard systems currently available on the market, thus substantially reducing TCO.
-
Product
Insulation Resistance Testers
-
UEi Test & Measurement Instruments
Measures the total resistance between any two points separated by electrical insulation.
-
Product
6-24V Circuit Tester
1789
-
Peaceful Thriving Enterprise Co Ltd
*Check on 6 and 24V.*For use on automotive fuse blocks, marine fuse blocks, light sockets and trailer wiring.
-
-
Product
Online PD Spot Tester
Liona
-
Cable testing and diagnostics with the BAUR liona. Liona is a portable online PD spot tester for measuring and locating partial discharges in cables and switchgear during normal mains operation. Liona lets you test cable systems and electrical equipment online without switching off partial discharge activities, and then generate trend analyses. Even a PD spot test (duration: 5-10 minutes) is capable of reliably assessing the current status of your system.* Automatic PD detection during normal mains operation (without switching off the cable route)* With DeCIFer technology: PD identification based on 500 million measurement results* Precise online PD mapping with PD transponder
-
Product
Partial Discharge Tester
GTPD-2C
-
GTPD-2C Digital partial discharge tester is the digital partial discharge measuring and analyzer adopting the complete new generation technology. It is suitable for partial discharge detection in manufacturing factory and field handover test of transformers, generators, CT/PT, bushings, GIS, capacitors, power cables, switches and other high-voltage electrical equipment with various voltage levels and capacities.
-
Product
Power Steering Tester Kit
PST22A
-
Pinpoints defective power steering pumps, defective power steering gears and kinked or clogged power steering lines.
-
Product
Energized Distribution Insulator Tester
-
A sensitive voltmeter, the tester measures the difference in potential across each insulator in a suspect string. Comparative readings from satisfactory strings in the same operating situation quickly indicate the state of every insulator in the string being tested.
-
Product
Voltage Continuity Testers
-
Built tough for use in industrial and commercial environments, measures voltage range up to 1000 V AC and 1200 V DC (2100-Gamma only). Designed with reinforced components for dependable performance.
-
Product
3 Wire (Analogue) Earth Resistance Tester
2105 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
Product
Leak Tester
DRK134
-
Shandong Drick Instruments Co., Ltd.
DRK134 Leak Tester is an advanced and intelligent tester designed according to related standard. It is applicable to test the seal property of flexible pack in food industry, pharmacy industry and daily chemical industry.
-
Product
Automatic Battery Testers
-
T100BT is an innovative, modular battery testing equipment able to combine, on a single test platform, all the tests required to detect any possible defect on battery cells and modules: from defective cell wiring, to geometrical or surface irregularities, to out-of-specs performances.The battery tester is designed for the high-volume production test of battery modules composed by prismatic, cylindrical, or pouch cells, as well in a Lab/NPI version for engineering, prototypes and low-volume battery testing. The complete configurability allows you to equip the tester with the modules and tools you need to test your products, reaching the desired throughput.
-
Product
Automatic Hardness Tester
AF-400
-
Automatic Hardness Tester AF-400 Series for foams is totally changed the models and ASKER Flagship is born here. AF-400 Series is Automatic Hardness Tester for flexible urethane foams to be used for cushion materials in such products as car seat, furniture, and bedding, and for other kind of plastic foam.
-
Product
Compact Professional IC Tester
ChipMaster
-
The ABI ChipMaster Compact Professional is a low-cost, hand-held out-of-circuit IC tester. The ChipMaster is designed for testing digital ICs with up to 40 pins through a ZIF socket (see LinearMaster for analogue devices). A range of adapters is also available for SOIC and PLCC devices.
-
Product
Burn-in Board Continuity Tester
CT-1
-
Burn-in Board Coninuity Tester. Verifies burn-in board continuity and component tolerances. 768 I/O channels, can be forced to the constant current source or grounded independently. Highly accurate measurement of resistance, voltage, and capacitance using a pair of precision instrumentation amplifiers.
-
Product
Ground Resistivity and EarthService Tester
AD-510
-
Large, readable LCD display (2000 counts), Instant battery life indicator, Test frequency: 128 Hz (quartz generator), Test Voltage: max 30 V peak-to-peak, Range: 0,01 W ? 2 k W. Accuracy resistance measurement: 1 % 2 digits,
-
Product
DC Hipot Tester,
294
-
Our Model 294 is a simple-to-use DC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). The 294 DC Hipot Tester includes all the features you need to get the job done and move on. Make testing simple with common sense security settings. PLC Remote allows you to make DC Hipot Testing safer with Personal Protective Equipment (PPE).
