Distribution Amplifiers
amplify each output from input's split.
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Video Distribution Amplifiers
-
Product
Amplifiers
MMICs
-
RF core has been innovating GaN-based MMIC solutions for active phased array system pursuing more ease of use, higher performance, lower SWaP (Size, Weight, and Power) as well as lower cost. We aim at integrating all components of TRM front-end for active phased array on single die.
-
Product
Voltage Controlled Amplifiers
-
Teledyne Microwave Solutions (TMS) offers a variety of high-performance voltage controlled amplifiers operating over a 5 to 2500 MHz range. These VCAmps feature an AGC range of 20.0 - 50.0 dB and Response Times from 3 – 25µs. TMS has a broad range of component products to meet your demanding needs.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
SV Range Broadband Power Amplifiers 0.8 GHZ - 3.2 GHZ
SV Series
-
Class A solid stateBroadband (instantaneous single band): 80 MHz 1000 MHzTypical output power : 100 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 100 W and H < -20 dBc up to 450 MHz andP1dB > 65 W and H < -20 dBc from 450 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to MT 200 possibleReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Mixer Amplifiers
-
Tailored for various establishments such as restaurants, schools, churches, clubs, and more. This versatile unit offers a compact and highly efficient solution to seamlessly blend up to three audio sources.
-
Product
Power Amplifiers
-
Applied Research and Technolgy
Drive studio monitors or installation speakers in any environment.
-
Product
Conventional Panel-mounted Type Power Amplifier Control Unit
PAT01
-
PAT01 is a power amplifier control unit that controls timing output and reference signal test source for power amplifier.
-
Product
4-Quadrant Power Amplifier For Simulation Applicaton
PAV20000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
-
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
150 kHz-230 MHz Broadband Power Amplifiers
-
Output power up to 80W for standard conducted immunity testing. Our 150 kHz-230 MHz amplifier range covers output power ranging from 20 W to 80 W.
-
Product
Headphone Amplifier
MH-8
-
High-power headphone amplifier that distributes the stereo input to eight headphone outputs
-
Product
Low Noise Amplifiers for Radio Amateurs
-
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don't compromise and get technology from Kuhne electronic!
-
Product
Power Operational Amplifiers
-
ST offers a portfolio of power op-amps characterized for high output current, low drop and high gain. This makes them suitable for a wide range of applications and, in particular, for driving inductive loads such as motors and lamps, as well as in automotive applications offering superior performances. Our op-amps are available in insertion and surface-mount packages to meet different environmental requirements.
-
Product
Broadband Amplifiers
-
R&S broadband amplifiers are innovative solid-state solutions with exceptional RF performance for generating RF power up to 13 kW in the frequency range of 4 kHz to 6 GHz. Designed as very compact amplifiers, at highest power density, they are robust against severest output mismatch while featuring high availability. Applications range from amplitude, frequency, phase, pulse to OFDM modulation.
-
Product
Low Noise Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
KeyLink's low noise amplifiers typically exhibit noise figures below 5.5dB and output 1dB compression points up 8dBm. These amplifiers are economical choices for general purpose applications. KeyLink's low noise amplifiers can be categorized as follows.
-
Product
LED LIGHT DISTRIBUTION TESTER
-
Essential elements among LED inspection categories are the light quality and intensity. Accurate measuring for optical characteristic requires diverse photo-measurement technology which fits into production lines. This system extracts conditions necessary for optical measuring optical characteristics on production equipment through accurate measurement both of the quality and of intensity of LED light distribution characteristics.
-
Product
Low Noise Amplifier
DLNA8-40-50-2582
-
Low Noise Amplifier, Frequency 40~50GHz, Gain 38dB, Noise figure 3dB, P-1dB 13dBm, 1.85mm-Female Removable
-
Product
Tone Amplifier And Tone Generator Set
AM5/TG5xs
-
The New Tone & Amp Set are state of the Art Testers offering touch button technology, visual qTrace (quick trace) as well as audio tracer tone technology providing accurate wire location, high output volume and sensitivity, tone tracker functionality, Visual/Audible indication of Digital Traffic, filtered amplification with multiple volume levels and two normal tones and four tonetracker tones with constant and variable interrupt rates, short detection and indication, capacitive output connection, Quick change battery and low battery indication in New custom designed High impact resistance enclosures, fully sealed to IP67.
-
-
Product
34945EXT Distribution Board, For Two 87104x/106x L7x0xx Multiport Or 87406B Matrix Switches
Y1151A
Distribution Board
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
Product
Bridge Amplifier
90376
-
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
Product
Solid State Broadband High Power Amplifier
Model 2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated, and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability, and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. The amplifier is constructed within a single 5RU drawerincluding the forced air-cooling. Available operating voltage configurations are single-phase 220 VAC up to 400 Hz and 28 VDC.
-
Product
Universal Amplifier Heatsinks
-
A universal heatsink, which is designed and fabricated for Eravant's active device applications with up to 15-watt power dissipation. The heatsink consists of the main heatsink body, a DC fan and a heat spreader. The heat spreader is also known as adapter, which is used to bridge the mounting gap between the heat sink main body and the to-be-heat-sunk devices, such as power amplifier, frequency active multiplier, oscillator, transmitter and transceiver due to various mounting hole locations. The heat spreader offers various mounting patterns to accommodate more than 15 product models. This heatsink is not only designed for Eravant's standard products and Uni-Guide™ featured products, but also for many industrial standard microwave and millimeter wave products offered by other manufacturers. Other heatsinks with different power dissipation capacities are offered under different model numbers.
-
Product
Programmable Gain Amplifiers
-
Analog Devices programmable gain amplifiers (PGAs) provide excellent gain accuracy, channel-to-channel matching specifications, and low 1 ppm/°C drift. Set your gain with a simple serial or parallel interface from 1 V/V to over 4000 V/V.
-
Product
SX Range Broadband Power Amplifiers 0.8 GHZ - 6 GHZ
SX Series
-
Solid-state amplifier / Class A. Broadband (Dual-band): 0.8 GHz - 6 GHz. Typical output power:
-
Product
Variable Gain Amplifiers
-
50 dB Gain, 14 dBm P1dB, 100 MHz to 18 GHz, Rack Mount, Variable Gain Amplifier, 6.5 dB NF, SMA
-
Product
Single-Ended SD Video Filter Amplifier With Output Short-To-Battery Protection
ADA4432-1
-
The ADA4432-1 is a single-ended output fully integrated video reconstruction filter that combines overvoltage protection (short-to-battery [STB] protection) and short-to-ground (STG) protection on the outputs, with excellent video specifications and low power consumption. The combination of STB protection and robust ESD tolerance allows the ADA4432-1 to provide superior protection in the hostile automotive environment.
-
Product
C-Band Single Channel Line Amplifier EDFA (SLA)
HSA4200 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4200 series is a line EDFA designed specifically for single wavelength optic transmission system. It is installed in the middle of the transmission line, replacing the traditional relay station, to compensate the optical power loss in the line and extend the signal transmission distance.
-
Product
Bi-Directional Amplifier
-
RF Lambda’s bi-directional amplifiers can be used in repeater type applications where a single conductor is used for both receive and transmit. These amplifiers offer low noise figure and high linearity. Hermetically sealed options are available upon request.
-
Product
Microwave Power Amplifier 1/2 Watt 100 MHz to 20 GHz
GT-1020A
-
The Spanawave/Giga-tronics GT-1020A Microwave Power Amplifier incorporates broadband MMIC-based architecture. These state-of-the-art amplifiers are based on solid-state parallel MMIC design with exceptionally wide bandwidth and high power. The unique circuit topology is highly reliable, with performance that excels where extremes of bandwidth and power are demanded.
