-
Product
2 GHz to 6 GHz, 25 W Power Amplifier Module
HMC7748
-
The HMC7748 is a multistage power amplifier (PA) that provides 25 W of saturated output power across the band of 2 GHz to 6 GHz. It draws 0.7 A from a 12 V supply and up to 4 A from a 28 V supply. Input signals of as much as −8 dBm are acceptable, and the module has small signal gain of 60 dB. The 12 V supply is regulated internally and generates the negative voltage required for the gate bias. Built-in bias sequencing prevents the drain voltages for the amplifier stages from being applied without the negative voltage present, which protects the amplifiers if 28 V is applied without 12 V supply applied.
-
Product
Very Broadband Seismometer
KS-54000/KS-1
-
Geotech's Model KS-54000 is a borehole, Model KS-1 a vault, three-component seismometer, designed for ultra low-noise monitoring for frequencies from 0.003 to 5 Hz, being below the Low Noise Model for frequencies up to 5 Hz.
-
Product
Test & Measurement Instrument Amplifiers
MPA-series
-
The MPA-series Test & Measurement Instrument Amplifiers are based on state-of-the-art GaN PA modules and operate from 0.7 to 26.5 GHz (multiple frequency options are available). They provide High continuous power across the band, high linearity for wideband communications testing, have variable gain adjustment and a high-resolution display shows amplifier status. Amplifiers offer a wide range of application-specific requirements including simultaneous high-power, wide bandwidth, low harmonic power and high linearity.
-
Product
Composite 1×24 Video Distribution Amplifier
VDA124RM
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Measurement Amplifier In Rugged IP65 Housing
-
INELTA Sensorsysteme GmbH & Co. KG
For DMS Force Sensors and LVDT
-
Product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
Product
Load Cell Amplifiers
-
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
Product
Rack Mount Type Amplifiers
-
Amplifiers for each of O-, S-, C- and L-bands– Compatible with high-speed transmission (up to 100 Gbps)– Available for all signal types and protocols– Compatible with transmitters from all manufacturers– Compatible with SNMP
-
Product
HDMI Audio Extractor with Audio Amplifier, RS-232 and IP Control
EMX-I-AMP
-
The EMX-AMP is a 4K HDMI Audio Extractor with built-in 50 watt audio amplifier for direct connection of 8 ohm speakers. The device also provides line-level stereo Aux audio input and allows audio mixing of HDMI audio with the Aux input. Volume can be controlled from the front panel, RS-232, or external digital rotary pot (encoder) that can be mounted on a wall-plate.
-
Product
Ultra-low Noise High Voltage Amplifier
WMA-200
-
The Falco Systems WMA-200 model is a high quality, high voltage, linear laboratory amplifier optimized for experiments requiring world-class, ultra-low output noise. The excellent noise performance, combined with the wide bandwidth and large voltage range make this amplifier the preferred choice for the most demanding precision positioning systems. The amplifier will routinely enable sub-atomic positioning resolution with piezo positioning systems and MEMS devices. Two WMA-200 amplifiers and a WMA-IB-LN phase inverter - buffer can be used to double the output voltage.
-
Product
Power Amplifier
DPA8-0.4-22G-2032
-
Power Amplifier, Frequency 0.4~22GHz, Gain 40dB, Psat 30dBm, SMA Female
-
Product
Composite 2×12 Video Distribution Amplifier
VDA212RM
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
RF Amplifier
SA812AGC
-
Hangzhou Softel Optic Co., Ltd.
SA812AGC Field Bidirectional AGC Amplifier is a new high gain amplifier. Adopt optimized circuit design and scientific and rational process. High performance AGC control circuit inside is useful for stable gain and low distortion. It's the best choice for large and medium-sized bidirectional CATV transmission network.
-
Product
Amplifier Dyno
AD-1
-
The AD-1 Amplifier Dyno is a tool that is designed to be used any place an amplifier exists. It can be used in a lab or production line to test true amplifier power output, quickly and easily. It is simple menu driven, does not require a computer, and cannot be cheated as the load banks are internal. It can be used in an automotive audio install shop to test true amplifier output while the amplifier is installed in the customer's vehicle.
-
Product
PXI Amplifier And Attenuator Modules
-
Pickering's PXI Amplifier and Attenuator Modules include our accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices. The other programmable attenuator available has a bandwidth between 10MHz and 6GHz available in triple or hex formats.
-
Product
MOSFETs For Amplifier
-
These are enhanced power MOSFETs with excellent frequency characteristics. They are ideal for audio amplifier output.
-
Product
RF High Power Amplifier Modules
-
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the Ka-band (29 GHz to 31 GHz). Our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of test, radar, and aerospace and defense applications that they are used in.
-
Product
Limiting Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's limiting amplifiers use FET device with good consistency and distributed traveling wave amplifying circuit to design. Good amplitude and phase consistency characteristics can be achieved in a wide input dynamic range. It's the key component of the electronic system. Keylink's limiting amplifiers can be categorized as follows.
-
Product
Ultra-broadband Power Amplifier Systems
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink provides ultra-broadband power amplifier systems in rack-mounted configuration with output power capacity from 50-Watt to 2000-Watt for applications including EMC testing, communications, and TWT replacement.
-
Product
Air Amplifiers
-
Nex Flow® Air amplifiers are compact, low cost air flow “movers” that are virtually maintenance free. Applications include the venting of fumes and smoke, conveying of low weight materials, and entraining a high volume of air to cool, blow off, and dry. Air Amplfiiers use the “Coanda effect” to draw in the surrounding atmosphereic air while consuming only aminimal amount of compressed air. These products can amplify airflow up to 17 times (depending on the size) resulting in dramatcally reduced levels of noise. Air Amplifiers (also called Air Movers) draw in atmospheric air from the back of the unit as well as having downstream entrainment further amplifying the flow. They are used for cooling and venting. While the force produced for blow off decreases as the amplifier outlet diameter increases, these Air Movers are ideal for cooling because of the high velocity outlet fow and and are much more effective for cooling compaed to air nozzles.
-
Product
Fiber Optic Sensor & Amplifier
FG-1300 | FS-5500/FS-540
-
The FG-1300 is a non-contact type high-performance amplifier that emits red light from LED to a rotating object, and detects the variation of the reflected red light amount.This amplifier is used in combination with an exclusive detector FS-5500*/FS-540 Fiber Optic Sensors which has adopted environment resistant design. The glass fibers are covered with flexible stainless steel tube for rotation measurement in limited space.
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-816
-
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Digital Quad-Phase "DSP" Lock-In Amplifier -
eLockIn203
-
The eLockIn203 can be used as spectrum analyser, as oscilloscope, as sinus generator or as measurement control system.
-
Product
System Amplifiers
-
The perfect combination of high performance, wide bandwidth and low noise
-
Product
40mA Multi-Channel Amplifier
-
For the precise nanometer movement of actuators and other piezo products, an amplifier is required. Multi-channel amplifiers allow you to control multiple actuators or piezo products with a single amplifier. The NV40/3 piezo amplifier was designed for controlling low voltage piezo elements. It includes a voltage amplifier, a display and a PC-interface. The high-resolution display shows the voltage of the actuator, along with the mode of operation and the temperature inside the amplifier.
-
Product
High-end Cable DAC & Amplifier
Impacto essential
-
Beyerdynamic Digitalize high-end headphones.
-
Product
Standard CW Amplifiers
-
An electronic device that boosts radio frequency (RF) or optical signals while maintaining an uninterrupted, constant output waveform.
-
Product
Dual Channel High Voltage Linear Amplifier
A800D
-
This unit contains two independent A800 amplifiers that share common ground reference and power supply.
-
Product
RF Benchtop / EMC Amplifier (110/220V)
-
RF-Lambda is a world leader in the design and manufacture of high-power, solid-state, broadband AC-powered EMC power amplifiers.
