Radio Test Sets
See Also: TPS
-
Product
Over-the-Air Radio Waveform Analyzer Service
DiagnostX
-
Service enables LMR managers to have all of their active radios evaluated for performance and alignment Over-the-Air, without user intervention. A detailed monthly report will be sent identifying those radios as “Failed”, “Passed” and “Never Received”. This service supports P25 Trunked, P25 Conventional and Legacy systems. Available January 2018
-
Product
Secondary Injection Test Set
PTE-100-C Plus
-
In the Pro version this voltage source incorporates a dedicated LCD display and its own BUS-PTE connection that make the operation easier and enable it to be used also with other sets in the PTE range.
-
Product
MIPI Radio Front-End
RFFE
-
Mobile phone radios have developed into highly complex, multi-band and multi-standard designs that often have multiple radio frequency (RF) signal chains. The MIPI Alliance Specification for RF Front-End Control Interface (RFFE) was developed to offer a common and widespread method for controlling RF front-end devices. The RFFE Master IP core typically resides in the RFIC in a mobile platform, and utilizes the RFFE bus to identify, program and monitor the registers in RF front end Slave devices through programmed IO. It is designed to support existing standards such as LTE, UMTS, HSPA and EGPRS, and is usable in configurations ranging from single Master/single Slave to multi-Master/multi-Slave.
-
Product
Software Defined Radio Firmware
FWSDR
-
The combination of the firmware FWSDR and the high-end digitizer ADQ14 creates a unique platform for software-defined radio. This 14-bit digitizer provides the high dynamic range needed in an RF environment and the interleaving technology provides high signal bandwidth coverage.The interleaving technology is provided through the use of SP Devices’ proprietary technology ADX which removes typical interleaving artifacts and enables the unique combination of bandwidth and dynamic range.
-
Product
Circuit Tester Set
TE6-0719
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*Needle point probes*Continuity tester requires one AAA battery, battery not included
-
Product
Two-Way Optical Loss Test Set
KI23422OLF-INGAAS-APC
-
A Two-Way Optical Loss Test set (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on single mode fiber with an APC connector at 1310 / 1550 nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use. The 650 nm VFL is on a separate port.
-
Product
CATR Benchtop Antenna Test System
ATS800B
Test System
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
SM & MM Quad Optical Loss Test Set
KI2724-INGAAS-APC
-
A SM & MM Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber with an APC connector at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful solution to improve test flexibility and productivity.
-
Product
Relay Buddy Adapter Set
190-4
-
*Expands the testing capability of your Relay Buddy! *3 pack of adapters allows testing of shielded relays, same relays tested by #190 Relay Buddy *Relay adapter plugs into Relay Buddy first *Shielded relay then plugs into the top of the adapter
-
Product
Three-Phase Relay Test Set
CMC 353
-
With its compact design and low weight of 13.3 kg / 29.3 lbs, the CMC 353 provides the perfect combination of portability and power. It is the ideal test set for three-phase protection testing and the commissioning of SCADA systems. The powerful current outputs (3 x 32 A / 430 VA) optimally support 5 A relay testing.
-
Product
Test Port Cable, 1 Mm
11500K
Test Port Cable
Connect test ports to devices, fixtures, or probe tips with this 20-cm cable featuring a return loss of 16 dB minimum
-
Product
Radio Frequency Probes (Automotive) HF66FAKRAm016G775MCXfF
1037623
-
The Radio Frequency Probes (Automotive) HF66FAKRAm016G775MCXfF are essential tools designed for dependable automotive applications. With a robust design, these coaxial probes operate comfortably within a temperature range of -45°C to +100°C, making them adaptable for various automotive environments. Their precise engineering ensures minimal impedance at 50 ohms, allowing for high-frequency performance up to 6 GHz, crucial for maintaining signal integrity during diagnostics and testing.
-
-
Product
Radio & Wireless Compliance Testing
-
EMC Technologies can provide the mandatory radio and wireless testing, approvals and certification services for major international and local markets such as European CE Marking, USA and Canada FCC and ISED certification, Japan MIC, Australian RCM and New Zealand GURL. Common standards we can test against include:
-
Product
Single-phase Relay Test Set
-
Weshine Electric Manufacturing Co., Ltd
Given the diverse functional requirements of the grid’s protection system, testing capabilities require a new level of sophisticated test hardware and software with which to analyse the entire protection system’s (or individual protection component’s) operation in "real life" situations. It is further necessary that these expanding testing capabilities be met with a similar improvement in the simplification of a test instrument’s user interface and software control.
-
Product
USRP‑2930, 20 MHz Bandwidth, 50 MHz to 2.2 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device
781910-01
Software Defined Radio Device
20 MHz Bandwidth, 50 MHz to 2.2 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device - The USRP‑2930 is a tunable RF transceiver with a high-speed analog‑to‑digital converter and digital‑to‑analog converter for streaming baseband I and Q signals to a host PC over 1 Gigabit Ethernet. It also features a GPS-disciplined oscillator (GPSDO) with PPS accuracy of ±50 ns. You also can use the NI USRP‑2930 for the following communications applications: white space; broadcast FM; public safety; land-mobile, low-power unlicensed devices on industrial, scientific, and medical (ISM) bands; sensor networks; cell phone; amateur radio; or GPS.
-
Product
High Voltage Breakdown Test Sets
HT-Series
-
Dielectric Voltage Withstand Test or High Potential Test (HIPOT test) is a 100% production line test to verify the quality & electrical safety characteristics of products.
-
Product
PARTIAL DISCHARGE test set
pdnt02
-
International Biological Laboratories
This Test Kit is used for non-destructive means of assessing the quality of high voltage transformers, motors, cables etc., which are used in generation & distribution of electric power.
-
Product
Communications Manufacturing Test Set
CMW100
-
The R&S®CMW100 communications manufacturing test set is based on the R&S®CMW platform. The flexible RF interface permits simultaneous testing of up to eight devices. The R&S®CMW100 remote control and measurement concepts are compatible with the R&S®CMW500. The R&S®CMW100 is optimized for cost-effective calibration and verification of wireless devices in non-signaling mode (analyzer/generator). The tester provides a new eco-friendly hardware concept, featuring extremely low energy consumption and a very compact size, making it ideal for use in fully automated robotic production lines. It supports LTE, 5G NR, WLAN, Bluetooth® and IoT technologies, making it ready for today and tomorrow.
-
Product
EBIRST 50-pin D-type To 37-pin D-type Adapter
93-005-418
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Automated Multi-Functional Tester
QTouch 1408 C
Functional Test
Qmax Test Technologies Pvt. Ltd.
QTouch 1408 C – Automated Multi-Functional Tester with in-built camera is designed to make automatic image capturing and probing of electrical signals with ease and speed especially in PCBs with high density/high pin count device that are mounted on the PCB. It is designed to move on X, Y, Z directions making it possible to probe every component as close as 20 mils. Easy tagging feature allows the user to get the real time XY coordinates using the library information with minimal intervention. CAD import feature is available for Auto Test Generation/to extract the XY coordinates from the CAD data. Qmax Automated Multi Functional Tester can perform Board level functional test of a PCB and guided probe / Back tracking diagnostics utility to reliably test Digital, Analog and Mixed Signal PCBs and fault isolation to the PCB level or component level.
-
Product
Radio Frequency Probe HF860PCBGSG016G960MCXfPV2
1043726
-
The HF860PCBGSG016G960MCXfPV2 is a high-performance radio frequency probe designed for industrial applications, specifically optimized for PCB-GSG connections. This model is built to withstand extreme temperatures ranging from -45°C to +100°C, making it suitable for a variety of environments. Its coaxial design, characterized by a pitch of 6.00 mm (236 mil), ensures a reliable connection that supports continuous current operations up to 5 A and frequency handling up to 6 GHz, making it ideal for high-precision measurements in radio frequency testing.
-
Product
Radio Frequency Probes HF77HMTDmWPCable0120G750HMTDmF
1176857
-
Introducing the HF77HMTDmWPCable0120G750HMTDmF, a highly specialized coaxial probe designed for precise and reliable radio frequency applications. With a compact design featuring a pitch of 12 mm (473 mil), this probe can effectively handle frequencies up to 20 GHz, making it an ideal choice for high-performance scenarios in telecommunications and electronics testing.
-
Product
Modular TDM / IP Split Mount Radio System
CFIP PhoeniX M
-
CFIP PhoeniX M split mount system consists of PhoeniX M IDU and PhoeniX ODU (XPIC functionality supported). PhoeniX M IDU provides up to 63E1 and 2xSTM-1 bringing the total maximum capacity to 348 Mbps full duplex.
-
Product
In-Circuit Testing and Test Engineering
-
5184 Test NodesHPUX or Windows60 Mhz ASRU Frequency Counter, Timer10 Mhz Clock, 6 Mhz data ratesVector Test for VLSI, PLCC & ASICSTestjet and VTEP Vectorless TestingAdvanced Boundary ScanSilicon Nails AvailableSeries V upgradeable
-
Product
Combined High Voltage Test Set
-
is extensively used to measure AC and DC voltage of different electrical devices.
-
Product
Miniature Two-Point Probe Set
PRF-922B
-
The PRF-922B Miniature Two Point probe accurately measures point-to-point resistance of small areas. Like Prostat's PRF-912B Miniature Concentric Ring, the PRF-922B is capable of measurements up to 1.0x1012 ohms. Built-in distance stops provide consistent electrode to sample pressure for developing repeatable measurements. Use the PRF-922B to measure small material samples, hard to assess molded areas, edges of parts, tray or tape cells and other very small objects and surfaces. The assembly is supplied with replaceable conductive electrode covers to enhance contact resistance on irregular surfaces and composition materials. Thus, measurements may be made with either the gold plated electrode contacts, or via conductive rubber covers.
-
Product
Drive Controller Function Test – Universal Functional Test System for Industrial Electronics
Functional Test
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.
-
Product
Loss Test Set
HPT-5100
-
The HPT-5100 represents a significant improvement in technology at a competitive price. This high performance loss test set has advanced features commonly found in instruments costing far more.
-
Product
Air Data Test Sets
-
For calibrating altimeters, airspeed indicators, rate-of-climbindicators and other avionic instruments.
