Showing results: 841 - 855 of 1382 items found.
-
SI-60F -
LINEEYE Co., Ltd.
SI-60F is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). It is the environment-friendly design, such as low power consumption from DC5V and compact body (resource saving).
-
PMC-MC-X2 -
Dynamic Engineering
The PMC-MC-X2 adapter / carrier converter card provides the ability to install up to 2 (two) PMC cards into a small enclosure. The PMC-MC-X2 has one PMC card slot mounted front and rear to create a compact arrangement with 2 PMC slots. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
PMC-MC-X4 -
Dynamic Engineering
The PMC-MC-X4 adapter / carrier converter card provides the ability to install up to 4 (four) PMC cards into a small enclosure. The PMC-MC-X4 has two PMC card slots mounted front and rear to create a compact arrangement with 4 PMC slots. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
BitNet -
NG Systems Ltd
BitNet is a 4-bit digital to Ethernet converter that enables up to four, volt-free contact inputs to be transmitted on to a local area network (LAN). Each input is assigned a unique number to identify any contact that has closed or opened. A maximum of 16 BitNets may coexist on the LAN which will facilitate up to 64 volt-free inputs.
-
HE-960RW-GC(W) -
HORIBA, Ltd.
The HE-960RW-GC(W) is a 2-channel simultaneous-measurement carbon sensor, resistivity meter that can be connected with two sensors. The measurement range is: 0 - 100.0 MΩ・cm.The high performance and high precision is maintained while simultaneously measuring the output of the resistivity of different two locations. This is carried out in a single converter for overall cost efficient performance.
-
PAS 9818/AO -
Precision Analog Systems Co.
The PAS 9818/AO provides eight programmable current output channels with sixteen bit resolution on a 6U VME card. Each channel consists of a high speed Digital-to-Analog Converter (DAC), followed by a high power operational amplifier. The output amplifier is configured to provide an output current that is proportional to the output voltage from the DAC.
-
FC5003 -
Behlman Electronics Inc.
Behlman’s FC5003 is a ruggedly built, COTS frequency converter designed to convert 120/208 VAC, 3-phase, 60 Hz, ground power to 115/200 VAC, 3-phase, 400 Hz, aircraft power. The FC5003 is in a rugged 6U (10.5”H) 19 inch rack mount chassis with an input line cord with plug and an output receptacle.
-
Renesas Electronics Corp.
Renesas Electronics offers SiP products with integrated MOSFETs to enable easy configuration of high-performance multi-phase power supplies. They combine in a single package either controller, driver, and MOSFETs or driver and MOSFETs. These products make it easy to build a high-performance DC/DC converter while reducing stray capacitance and inductance, and achieving higher mounting density.
-
PAS 9782/GEN -
Precision Analog Systems Co.
The PAS 9782/GEN is a VME based, eight channel function generator card. Each channel contains a Direct Digital Synthesis (DDS) chip that can be programmed to generate sine wave output signals. This DDS device is a Numerically Controlled Oscillator (NCO), employing a phase accumulator, a sine look-up table and a 10 bit D/A converter.
-
PAS 9883/GEN -
Precision Analog Systems Co.
The PAS 9883/GEN is a VME based, eight channel function generator card. Each channel contains a Direct Digital Synthesis (DDS) chip that can be programmed to generate sine wave output signals. This DDS device is a Numerically Controlled Oscillator (NCO), employing a phase accumulator, a sine look-up table and a 10 bit D/A converter.
-
781909-01 -
NI
20 MHz Bandwidth, 400 MHz to 4.4 GHz Software Defined Radio Device - The USRP‑2922 is a tunable RF transceiver with a high-speed analog‑to‑digital converter and digital‑to‑analog converter for streaming baseband I and Q signals to a host PC over 1 Gigabit Ethernet. You can also use the USRP‑2922 for the following communications applications: WiFi, WiMax, S‑band transceivers, and 2.4 GHz industrial, scientific, and medical (ISM) band transceivers.
-
HDR -
Computer Conversions Corporation
The HDR Series are sub-miniature modules that are; size comparable, low cost alternatives to Hybrid type D-R and D-S converters. Because of their advanced modular design the HDRL series features short lead times that are neither limited to infrequent hybrid production cycles, long term parts allocation, minimum quantity purchases, or hybrid obsolescence related concerns.
-
PCI3IP -
Dynamic Engineering
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. The PCI3IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI3IP is a half size PCI card with 3 IP sites; compatible with the smallest chassis and the tallest processors that prevent full size solutions.
-
PCIeBPMCX1 -
Dynamic Engineering
Now you can use your PMC with a new PC. The new PC´s have PCI Express connectors in larger quantities than PCI slots. The PCIeBPMCX1 ( PCIe Bridge PMC 1 slot) adapter / carrier converter card provides the ability to install one PMC card into a standard PCIe (Express) 4 lane slot.
-
PSI -
Computer Conversions Corporation
Computer Conversions Solid State Selsyn/Resolver Indicator digitizes the outputs of Selsyns, Synchros and Resolvers for position indication and control applications. The Selsyn Indicator is designed to replace failure prone mechanical selsyn torque receivers, counters, etc. The tracking converters high noise immunity and high speed tracking characteristics make it ideal for use in industrial envrionments.