Phase Locked Loops
See Also: PLL
-
Product
Surge with 3 Phase Transfer Switch Consoles
TC Model
-
(Surge with 3 Phase Transfer Switch Consoles) Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TC" Model has the same characteristics as the "C" Model, but includes a Built-in 3 Phase Test Selector Switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
Loop Resistance Measuring Device According to DIN EN 61557-3 (VDE 0413-3)
-
PeakTech Prüf- und Messtechnik GmbH
A loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
Product
Pulsed Injection Locked IMPATT Amplifiers
-
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
One Phase Electric Power/Energy Calibrator
MC133
-
The MC133 master unit model is a one phase electric power/energy calibrator. It can supply the device under test with single phase precise voltage and current with calibrated phase shift along with DC voltage and current capability. Output voltage can be set in five ranges up to 280V and output current in six ranges up to 30A. Simulated electric power can be set independently for each phase. Frequency can be set from 15Hz to 1 kHz with resolution 0.001Hz to 0.01Hz. The MC133 Calibrator is equipped with 5 1/2 digital DC meter with DC ranges 20mA or 10V for direct calibration of various types of power transducers and wattmeters.
-
Product
Three Phase Site Energy Meter Test Instrument Type KP-P3001-A
-
Bofa Instrument & Equipment Co., Ltd
Three-phase site energy meter test instrument type KP-P3001-A (without voltage and current source) is an ideal instrument to test all kind three-phase energy meters accuracy below 0.2, especially for meters on site. When we want test a meter errors, the tested meter must be on load condition (or we can say the tested meter must be working). The instrument can test the errors, by comparing energy impulse from the tested meter with energy impulse from the reference meter which inside the instrument. The equipment is box structure and weight is very light, easy to carry, it is very convenience to test the installed meters on site.
-
Product
Natural Cooling Input 380VAC 3 Phase to Output 190-300VDC 10A-40A Rectifier Battery Charger
SD230D20ZZ
-
Zhejiang Sandi Electric Co., Ltd
SANDI “SD” series intelligent high-frequency switch power supply modules are specially developed to meet the demands of modern DC system. The charger rectifiers are designed with world leading patent technology “resonant voltage type soft switching power supply technology”. They feature high efficiency and stability, intelligent control, small size and light weight. Standard RS-485 interface, easy to connect with automation system. “Four remotes” functions, intelligent management. The products are widely used in power plant, substations and etc..
-
Product
Short Circuit Loop Impedance Meter
AMZC-305
-
Loop impedance measurement with resolution 0,01Ω ; Loop impedance measurement without tripping the circuit breaker > 30mA with resolution 0,01Ω (100...440V) ; Measurements possible in installations 110/190V, 115/200V, 127/220V, 220/380V, 230/400V, 240/415V, 290/500V and 400/690V (range 100...750V)
-
Product
Motor&Phase Rotation Indicator
-
Precision Mastech Enterprises Co.
A diagnostic tool used to identify the sequence or \(A,B,C\)) of a 3-phase power supply and determine the proper direction of rotation for 3-phase motors.
-
Product
Digital Image Correlation System for Complete 3D Warpage, Thermal Expansion, and Strain Analysis of Materials and Components in the Heating and Cooling Phase
Q-400 TCT
-
The Q-400 TCT system is designed for complete three-dimensional and highly sensitive warpage, thermal expansion measurement and strain analysis of materials and components in the heating and cooling phase. Areas from 50 mm x 70 mm down to 2 mm x 3 mm can be investigated. Measurements can be done from room temperature up to 300°C and down to -40°C. The system is specially suited for thermal expansion measurement of electronic components and is frequently used in the development and testing of complex anisotropic materials, components, and structures in electronic applications.
-
Product
Single Phase Din Rail Multi-Tariff Energy Meter Type DDS999D
-
Bofa Instrument & Equipment Co., Ltd
Single phase Din rail multi-tariff energy meter type DDSF999D is a new type of single phase electronic multi-rate energy meter, which accords international standard IEC61036. It features: good reliability, small volume, light weight, convenient installation, etc.
-
-
Product
Phased Array Corrosion Mapping Software
Concerto
-
Concerto is a UT acquisition and analysis software specially designed for Phased Array corrosion mapping. For the tough field conditions that operators deal with Concerto features no menu, less than 18 icons, and few controls so that operators can easily work and not be bothered by complex GUIs. Concerto is simple and easy to work with yet WT, Surface, and back wall C-scan can still be analyzed and setting can be changed using the same acquired data.
-
Product
Phase Angle Voltmeters
Phase Angle Voltmeter
Since the development of the first Phase Angle Voltmeter (PAV) over 50 years ago, North Atlantic Industries has been the industry leader in AC Measurement Instrumentation. Our name has become synonymous with innovation and quality. Our products, specifically designed for defense, industrial, and commercial applications, deliver industry-leading accuracy, repeatability, and reliability.NAI’s units of today are actually multifunction Digital Analyzing Voltmeters that combine a complete Voltmeter, a Phase Angle Voltmeter, and a Waveform Signal Analyzer in a single microprocessor-based instrument. With these versatile and flexible instruments, a wide range of tests can be performed, either manually using the front panel controls or automatically using the IEEE-488 bus. Designed for the Synchro/Resolver and LVDT/RVDT marketplace, NAI’s Voltmeters are used in a variety of applications.
-
Product
Phase Detectors
-
High DC output versus phaseLow DC offsetRugged metal coaxial packageTiny surface mount packages, 0.38 x 0.50 x .023 in.
-
-
Product
9KHz-3.2GHz, Spectrum Analyzer, Phase Noise<-98dBc/Hz, Amplitude Accuracy<0.7dB, 10.1" Color Display
T3SA3200
Spectrum Analyzer
9KHz-3.2GHz, Spectrum Analyzer, Phase Noise<-98dBc/Hz, Amplitude Accuracy<0.7dB, 10.1" Color Display.
-
Product
Scienlab Regenerative 3‑Phase AC Emulator
SL1200A Series
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Phase ID Systems
-
LED Meter Probe allows the user to take Real time Phase Angle readings along with AC nominal voltage readings. A PD800W LED Meter Probe works in conjunction with the Receive Unit to verify phase identification along with the actual phase angle data. This is all done without any calculations or data transfer from the field to a base computer. The meter probe and reference probe or receive unit can operate at 100 feet of separation and up to 300 feet line of sight separation. In the event that this distance would need to be greater, the Receive Unit can be unplugged from the charging cable and taken into the field while operating on it's rechargeable batteries for up to 8 hours at a time.
-
Product
Rail Wheel Testing Using Phased Array System
ECHOMAC® PA Wheel Tester
-
MAC introduces two versions of Rail Wheel Testers using ECHOMAC® PA platform based on customer requirements. One is a semi-automated solution using local immersion technique. Used for tread inspection of new and/or reprofiled wheels. This solution meets or exceeds EN13262, ISO5948 or AAR M-107/M-208 standards for tread inspection. The second solution is a fully automated immersion tank. Performs tread and face inspection of rail wheels using two phased array probes simultaneously. This solution meets or exceeds EN13262, ISO5948 or AAR M-107/M-208 standards for tread and face inspection, while monitoring the backwall on the face side per EN 13262.
-
Product
Regenerative AC Emulator, 600 VAC, 125 A, 90 KVA, 3‑Phase
SL1203A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Line Loop Tester
8455
-
Simpson?s Model 8455 Line Loop tester detects line shorts, opens and multiple ringers, DC voltages and loop resistance. It can measure DC voltage up to 100 volts and loop resistance to 2 megohms. A front panel ?reverse polarity? switch allows changing polarity positions quicker and easier than manually switching test leads when making line checks.
-
Product
Field Testing Equipment for 3 Phase Energy Meter
SY3002
-
Hong Kong Songyang Industrial Ltd.
The field-testing instrument SY3002 is made by using the newest international digital electron technical skill To use DSP processor, as the axis to install this intelligent comprehensive automation field-testing instrument, which comes with a portable computer, the 11.3" colorful display screen, and Chinese characters operation menu suggestion.
-
Product
Dual Channel HV Amplifier with Phase Inverter
A800DI
-
This unit contains two independent A800 amplifiers that share common ground reference and power supply. Please see A800 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase.
-
Product
USB3, 3 meter, Type-A to Micro-B (Locking) Cable
USB 3.1 Locking Cable
-
USB3, 3 meter, Type-A to Micro-B (Locking) Cable.
-
Product
ThePoint - Loop Powered Level Switch
-
ThePoint Loop Powered two wire level switch provides a current output and has hazardous area approvals making it a good choice for most of your point level application requirements. ThePoint level sensing device offering is suitable for most temperature, pressure, and material types.
-
Product
180 Degree Phase Shifter
-
- Weather proof housing and galvanized mounting hardware- 5 kW continuous duty for reliability- 12 V DC 100 mA control voltage and current – for easy integration- Lightning protection
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 4 Channel
43-765-004
Analog Output Module
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Single Phase Reference Standard Meter
-
Signals & Systems India Private Limited
The Single Phase Portable Reference Standard (SPRS-1102) from SANDS is a portable meter test equipment that helps to calibrate the error present in the single-phase energy meter i.e. the meter under test (MUT). The SPRS supports both static and electro-mechanical types of meters. It can also be used to compute the voltage, current, energy, phase angle etc of the meter under test. It has an LCD display and an alphanumeric keypad to suit the user. It can be interfaced with the PC for analysis. It has the capability of storing 1000 test results.
-
Product
Single Phase And Three Phase Ageing Bench Type KP-S31000
-
Bofa Instrument & Equipment Co., Ltd
This ageing bench is used for ageing single phase energy meter and three phase emergy meter in meter manufacturer. It consists two parts: Power source and meter rack (single phase and three phase), usually we sugest 1 power source + 9 single phase meter rack (96 positions each) or 6 three phase meter rack (48 positions each).
-
Product
Automatic Solid Phase Extraction Instrument
DRK-SPE216
-
Shandong Drick Instruments Co., Ltd.
The DRK-SPE216 automatic solid phase extraction instrument adopts a modular suspension design. It relies on a precise and flexible robotic arm, a multifunctional injection needle, and a highly integrated pipeline system, which greatly improves the efficiency of sample pretreatment and brings you easy and convenient Work experience.
