Serial I/O
Sequential input and output of data.
-
Product
Serial To Digital Interface Boards
-
*ICS's Serial to Digital Interface boards provide the user with digital IO signals that can be user configured to match virtually any application. Both boards are available with high power relay drivers and with optional firmware designed to simplify switching applications.*All boards are designed for mounting inside a chassis.
-
Product
3U CompactPCI Serial Cyclone®-V FPGA,10 ports RJ45 Ethernet
SY8-CYCLONE
-
The SY8-CYCLONE is a CPCI Serial FPGA based peripheral board with up to 10 RJ45 Ethernet ports. Via the PCI Express© x4 interface, FPGA can be used as Ethernet NIC, switch, router, or gateway.
-
Product
cPCI IP Carrier Module With Front And Rear I/O
DP-cPCI-5211
-
DP-cPCI-5211 IP carrier board provides electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.
-
Product
16-Ch Isolated Digital Input And 16-Ch Relay USB 3.0 I/O Module
USB-5862
Data Acquisition Module
USB 3.0 SuperSpeedDaisy chainable by built in USB hub16-ch Isolated Digital Input and 16-ch Form A-type Relay OutputWide input voltage range (10 ~ 30 VDC)High-voltage isolation on input channel (2,500 VDC )Quick removable European type connectorLED indicators for I/O statusSupported operating systems: Windows 10/11
-
Product
OMNIBUS Analog I/O Modules
-
I/O Mezzanine cards for Modular, Solomente & Data Acquisition boards
-
Product
CompactPCI® Serial MXM 3.0 Type B Graphics Module Carrier
SV2-MOVIE
-
3U Carrier for MXM 3.0 Type B graphics module, 4 x DisplayPort front panel connectors, installed PNY P5000 MXM, 192bit/GDDR5 16GB, 100W TDP 2048 CUDA Cores, 8HP heat sink.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
3U CompactPCI Serial 3-slot SSL w/ RTM w/ Ethernet
1CPCIS-303-L210
-
3U CompactPCI Serial Backplane with 3 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 2x CompactPCI S.0 peripheral slots, with connectors for RTMs (RearTransition Modules) in slots 2 to 3, Ethernet full mesh.
-
Product
SCB-100 Noise Rejecting, Shielded I/O Connector Block
776990-01
Terminal Block
100-Pin Female SCSI to 100-Pin Female Screw Terminal, Desktop Mount Terminal Block - The SCB-100 is a shielded I/O connector block for interfacing I/O signals to NI data acquisition devices with 100-pin connectors. Combined with the shielded cables, the SCB-100 provides rugged low-noise signal termination.
-
Product
Multifunction I/O
526
-
Four 24-bit quadrature encoder inputsFour 16-bit analog outputsEight 16-bit analog inputsEight digital I/OSingle supply (5 V) input powerProgrammable interrupt timerVersatile watchdog timerxPC Target Real-time rapid prototyping softwareavailable through MathWorks
-
Product
Regular Flex I/O For Reset, Remote Switch And 5VDC
98R17500802
Expansion Module
Flex I/O expansion on the front panel for same-side cablingReset, Remote Switch and 5VDCSupport MIC-770 V3 Fanless system
-
Product
PCI Multi-function I/O Module
APC730
-
APC730 I/O boards provide a variety of I/O functions on a single card. These high-density boards perform both high-speed and high-resolution A/D and D/A conversion and also handle digital I/O plus counter/timer functions.
-
Product
Passive Probe Interface Adapter
CX1151A
Digital I/O Adapter
The CX1151A is an adapter for passive probes for the voltage waveform measurements by the CX3300 series Device Current Waveform Analyzer.
-
Product
Easy I/O Flexibility Fanless Embedded Box PCs
ARK-2000 Series
Box PC
The Fanless PC ARK-2000 series is a brand new design with rich I/O, high flexibility and easy expansion capabilities. The rugged features of this Embedded Fanless PC include wide-input power ranges from 12V to 24V or 9~36V, wide temperature ranges from -20 ~ 70° C and structural strengthening. Multi-functional design technology simplifies your Embedded System applications.
-
Product
True Dual-Channel Analysis on iOS
IOScope
-
With IOScope, measure loudspeaker impedance, frequency response, and sensitivity. Measure a room impulse response. Tune a large sound reinforcement system, time-align a set of surround sound speakers, or optimize your home stereo. Determine the actual cutoff frequencies of your latest speaker crossover circuit, or teach your students the fundamentals of Fourier analysis of dynamic systems.
-
Product
General Purpose I/O Modules
HY-TTC 30XH
-
The HY-TTC 30XH is a CANopen based, user-friendly and smart Input/Output module that can be utilized as flexible control system extension in mobile applications. HY-TTC 30XH is used in combination with, and controlled by a master electronic control unit, communicating with the slave module via the standardized CANopen® protocol. By mounting the master control unit centrally on the machine and the I/O modules close to the sensors or actuators, a distributed electronic architecture can be implemented in order to reduce mounting time and cost for cabling.
-
Product
REM-11100, 2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O
784748-01
Voltage Input Module
2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O - The REM‑11100 is a voltage input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11100 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. This module features 2‑, 3‑, and 4‑wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling.
-
Product
Multifunction Analog I/O Card
LPCI-AIO16A
-
Model LPCI-AIO16A provides 500k samples/second, with 16-bit resolution, for the board’s 16 single-ended or 8 differential analog input channels. Also included are two 12-bit analog outputs, 16 digital I/O lines and an 8254 with three 16-bit counter/timers. The board meets the MD2 Low Profile PCI Bus Specification and can be installed in any 3.3V or 5V PCI or PCI-X slot.
-
Product
Analog I/O Board
VME-3128A
-
The VME-3128A scans 16, 32, 48 or 64 channels, continually digitizes all of them and stores the results. Choose from 64 differential or single-ended inputs and program VMEbus interrupts and interval timer to meet the unique requirements of your mission.
-
Product
PXI-7853, Virtex-5 LX85 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780341-01
Multifunction Reconfigurable I/O
Virtex-5 LX85 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7853 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7853 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
PXIe Semi-Dynamic Digital I/O Module, 16-Channel
42-419-004
Digital I/O Module
The 40-419-004 (PXI) and 42-419-004 (PXIe) are a 16-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
NI-6584, 16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
781290-01
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter
-
Product
RS-422/485 Serial Communication Card
LPCI-COM-1S
-
The PCI-COM-1S is a single port asynchronous serial communications card that can be installed in any 3.3V or 5V PCI slot computer. The card meets the MD1 PCI Low Profile Specification and is just 4.7 inches long. For low profile systems please use P/N LPCI-COM-1S for the card to be shipped with a low profile bracket.
-
Product
Digital I/O Boards
-
Cable Transfer speeds up to 400 mb/per second Large FPGA provides for flexable cable interface
-
Product
16-Bit, 8-Ch Analog Output PCI Card With 16-Ch Digital I/O
PCI-1723
Analog Output Card
Auto calibration functionA 16-bit DAC is equipped for each analog output channelSynchronized output functionOutput values retained after system hot reset2-port (16-channel) user-defined digital input/outputBoardID™ switch
-
Product
Test Slave For The LIN Bus With Various I/Os
PLIN slave
-
The PLIN slave is an evaluation board with an interface for a LIN 2.0 bus. The device also offers comprehensive I/O functionality, which is accessible via operating and display elements.
-
Product
Remote I/O
-
Schweitzer Engineering Laboratories, Inc.
Remote I/O modules transfer data from remote locations over fiber and expand the I/O of SEL relays, automation controllers, and other devices without modification to the control panel face.
-
Product
cPCI Serial 3U AC 300W
-
Hartmann’s cPCI Serial Power Supplies comply with PICMG and offer a wide range AC input with utilization of serial communication. These supplies are developed and produced with quality and durability in mind, at a price that won’t bankrupt your project. Talk to a Hartmann representative today about your power needs!
-
Product
Serial Communications Card
104-ICOM-2S
-
The Model 104-ICOM-2S Serial Communications Card can be installed in a PC/104 stack and provide effective communication on long lines in noisy environments. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
Product
OPC UA Ethernet I/O Modules
ADAM-6300
-
Industrial OPC UA Ethernet I/O Modules with Modbus protocol converge OT/IT with security, linking to SCADA and the cloud for remote monitoring.
