Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
20-Pin GMCT Cable, Female to Unterminated, Cut Ends, 10A, 2m
A020GFR-C-0C200
-
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
PMC-to-PCI Express Adapter (PCIe/PCI-e)
5243
-
Our PMC-to-PCI Express Adapter (PCIe/PCI-e) 1X (5243) permits the use of a single-wide PMC module in a 1x PCIe slot. The A and C rows of a 96-pin DIN connector, located toward the rear of the board, connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card.
-
Product
Signal, Insert, Receiver/ITA, QuadraPaddle ,SIM, Right Angle, 4 Pos, 1 Slot
610138126
-
This insert contains 4 right-angle QuadraPaddle contacts and is designed for soldering directly to a PCB as part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 1 of the 34 slots in this module.
-
Product
Ship-to-Shore Connector
-
Navigating the world’s shorelines just got easier with the Ship-to-Shore Connector (SSC). The SSC is the next generation of the Landing Craft, Air Cushion (LCAC), providing a modernized means to reach the world's shorelines for the next 30 years. The all-aluminum craft offers increased performance, reliability and maintainability and meets the Marine Corps’ requirements for increased payload and availability.
-
Product
TLP Probe Arm Kit
TPA-95
-
High Power Pulse Instruments GmbH
*Flexible pulse force, pulse sense combined TLP probe arm kit based on TPA-95L and TPA-95R*Compatible with typical standard micropositioner mechanical interfaces*4.7 kΩ pulse sense voltage divider, which results in a voltage transfer ratio of (4700 + 50)/50 = 95 : 1 into 50 Ω*Variable probe pitch configuration*1 m flexible 50 Ω cables with SMA connector for pulse sense*0.1 m flexible 50 Ω cables with SMA connector for pulse force*Tungsten probe tips*Can be used for chuck backside grounded TLP measurements
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Low PIM Coaxial Cable Assemblies
-
For applications that demand low VSWR, low insertion and low PIM cable assemblies; RFI now offers semi-rigid and corrugated cable assemblies with factory soldered N and DIN connectors. Assembled using the latest soldering equipment for years of performance reliability. Each assembly is tested for insertion loss, VSWR and PIM rating and is shipped with individual test data. Available using flexible or super flexible corrugated cables with a standard or fire retardant jacket.
-
Product
LXI Microwave Multiplexer, SP4T, 11-Bank, 26.5GHz, 50Ω, SMA
60-803-311
-
Our 60-803-311 is a 11 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-346-HI
-
The 40-230-346-HI (PXI) and 42-230-346-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 5.806MΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Cable, 96-Pin 1.27mm Pitch Female To Unterminated, Tinned Ends, Screwlocks, 2m
A096SFR-T-6A200
-
The 96-Pin 1.27mm Pitch to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
Product
LXI Dual 24x8 50 Ohm HF Matrix SMB
60-760-002
-
The 60-760 is a Dual 24x8 HF Matrix Module suitable for switching frequencies up to 50MHz. It has an impedance of 50 Ohm and uses SMB signal connectors, or with a larger case size, BNC Connectors. It is designed to provide simple and scalable switching for radio frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems. Software configuration allows the 60-760-002 to be set as a dual 24 by 8 matrix, a single 48 by 8 matrix and other configurations.
-
Product
Antenna Noise Canceller
ANC-4
-
The ANC-4 is an rf device that eliminates or reduces power line noise, BPL noise, computer noise, TV-generated interference, and other types of electrical noise. The ANC-4 unit connects right to the antenna connector of the receiver or transceiver to cancel locally generated noise before it gets into the receiver and affects the receiver AGC circuits.
-
Product
R6868, Low-Cost, Unshielded Ribbon Cable, 0.25 m
182482-0R25
-
68-Pin Female to 68-Pin Female, 1 Ribbon Connection Ribbon Cable - The R68F-68F Cable, sometimes referred to as the R68-68 or RC68-68, is a flat ribbon cable that connects to 68-pin NI data acquisition or digital I/O devices. The R68F-68F Cable is offered in different lengths and with D-SUB or VHDCI front end connectors.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to Female (Female Screwlocks), 2m
A200LMR-200LFR-5B200
-
This male to female 2m cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin connector and is constructed from 4 bundles of 50-wire round/flat ribbon cable. The connector assembly can be secured to the product by screwlocks.
-
Product
Dual PMC Carrier for 6U CompactPCI
TCP262
-
The TCP262 supports standard PMC front I/O and CompactPCI rear I/O fully compatible to the TCP260. The PMC slot 2 (upper PMC) I/O lines are connected directly to the CompactPCI connector J5. The PMC slot 1 (lower PMC) I/O lines are connected directly to the CompactPCI connector J3.
-
Product
Cable Assy 78-Pin D-Type M/M 1m
40-970-078-1m-MM
-
A 78-Pin D-Type cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable to its associated products. The 78-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m
A026HM5-C-0A050
-
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 40GHz, 50Ω, SMA-2.9, External Termination
40-781A-521
-
The 40-781A-521 (PXI) and 42-781A-521 (PXIe) are single SPDT 40GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
30" Ribbon Cable
CONM50-D37-30
-
A 30" ribbon cable transitions from individual IP modules on various carrier boards to a 37 pin D-sub female connector mounted on a PC expansion card end-panel. This allows external connection to pins 1-37 on an individual IP Module.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber
40-852A-318-M50
-
The 40/42-852A-318-M50 is a PXI/PXIe 8-channel multiplexer with MU (mini SC) connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
LXI Microwave Multiplexer, SP4T, 11-Bank, 50GHz, 50Ω, SMA-2.4
60-803-611
-
Our 60-803-611 is a 11 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
-
Product
Cable Assy 68-Pin SCSI Micro-D M/M 0.5m
40-970A-068-0.5m-MM
-
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-410-004
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
Front Panel Interfacing Kit: M9018A And M9019A
Y1270A
-
The Y1270A Front Panel Interfacing Kit for M9018A and M9019A PXIe chassis provides a rugged interface to the front panel connectors of modules installed in the chassis. The frame is provided with a semi-transparent cover which provides additional protection for front panel cables and connectors.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 2 20-Pin Female Power Connectors
540054010101
-
Cable Assembly, Receiver, TriPaddle, 20", 2 20-Pin Female Power Connectors
-
Product
GMCT 26-Pin RF Cable Assembly, 75Ω, Male To Unterminated, 2m, RG179 Cable
40-979-726-2m-FU
-
This 2m long cable assembly is part of a range of cables suitable for applications using the Positronic 26-pin GMCT 75Ω RF connector. It is constructed from RG179 silver plated copper clad steel cable with FEP insulation and a bandwidth of 500MHz. Screwlocks are provided to secure the connector to the associated product.
-
Product
160-Pin DIN41612 Connector, Crimp Pin, Female, 45º
40-960-160-F5
-
Suitable for users to create their own cable assemblies where a 45 degree down cable exit would be preferred. If the user requires the connector to have a second fixing then it can be fitted with an additional screwlock assembly 40-969-101 where applications permit.
-
Product
8-Channel VME Function Generator
V340
-
The V340 provides eight independent DDS-synthesized waveform outputs, each programmable for frequency and amplitude. Any output may be switched to a front-panel test connector, allowing in-crate calibration check without removing field cables.
-
Product
FiberPal OTDR
OT-9800
-
FiberPal OT-9800 OTDR series is designed with ultra portable, light, reliable and easy to use as Fiber Quick test and Troubleshooter to locating fiber connector, break and imperfections for FTTX, CATV and optical LANs. FiberPal OT-9800 OTDR series detects event locations along the optical fiber and displays the results on a portable device like notebook, Tablet PC and Mobiles phones with Android 4.x operation system. OT-9800 is with internal battery and Bluetooth function.
