Strain Gage Amplifiers
See Also: Strain Gages, Strain Gauges, Strain Gage Signal Conditioners
-
product
SOA & Raman Amplifier
They are designed for distributed Raman amplification in a narrow spectral range in C band.
-
product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3
The AAF-3 is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier ISA bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
product
Full W-Band Power Amplifier
SBP-7531142515-1010-E1
For communication and radar applications, SAGE Millimeter has released a new full W-Band power amplifier. Model SBP-7531142515-1010-E1 is a power amplifier with a typical small signal gain of 25 dB and a nominal output power of +15 dBm across the frequency range of 75 to 110 GHz. The DC power requirement for the amplifier is +15 VDC/190 mA. The mechanical configuration offers an in-line structure with WR-10 waveguides and UG-387/U-M flanges. Other port configurations, such as with 1 mm connectors or a right angle structure with WR-10 waveguides, are also available under different model numbers. Features include: Full Band, High Gain, High Output Power.
-
product
Waveguide Power Amplifiers
RF solid state power amplifier (SSPA) PE15A4006 from Pasternack is part of the largest selection of in-stock radio frequency microwave and millimeter wave amplifiers available for same-day shipment. This Pasternack solid state RF power amplifier is a medium power amp design constructed in a connectorized package. Our SSPA is designed with SMA connectors and rated at 1 Watt.
-
product
Torsion And Shear Strain Gauges
Shear/Torque Strain Gages are for measuring shear strain and torque, typical applications are for measurements on torsion bars and determining shear stresses in shear beam load cells.
-
product
8-Channel VME Strain Gauge/Load Cell Module
V385
The V385 is a VME/VXI compatible eight-channel strain-gauge signal conditioner applicable to generic bridge-type transducer applications. The V385 adds individual remote-sensed excitation supplies to each channel, increasing its precision over the V380's single excitation supply.
-
product
Dual-Mode Charge Amplifiers
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
product
Pressure, Strain And Shock Data Loggers
Dataloggers for pressure, bridge input for strain or load measurement and also tri-axial shock dataloggers with built in accelerometers.
-
product
Amplifiers
Elbit Systems of America’s secure networks and communication solutions provide warfighters secured and reliable radio communications for most operational applications. Our teams work hard to deliver a number of scalable options from extremely rugged to standard industrial or commercial specifications. Our family of Single-Channel and Dual-Channel Modular Power Amplifiers operates with current and next-gen radios and offer lightweight, compact solutions on most platforms. The modular design simplifies maintenance, provides customer flexibility, and accelerates the fielding of new capabilities.
-
product
Solid State Power Amplifiers (SSPAs)
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
* Ruggedized for use in pulsed airborne, naval and ground radar* Found in weather forecasting Doppler radar systems* Utilized world-wide in air traffic control and precision approach radar systems
-
product
Cylindrical Crankshaft/Camshaft Gage
1200-HC
The Adcole Model 1200 Cylindrical Coordinate Measurement Machine (CCMM) is a highly accurate gage for measuring camshafts, crankshafts and other cylindrical parts that feature tight part tolerances. The system employs a proprietary laser interferometer technology to deliver precise radial and length measurements.
-
product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
product
Power Amplifier (DC Powered)
RF Lambda’s DC solid state power amplifiers (PA) are used in a variety of applications and offer high output power, wide band operation and good linearity. Hermetically sealed options are available upon request.
-
product
Erbium Doped Fiber Amplifier
S-102
The EDFA slot module of FOTS system with built-in power booster EDFA module offers a special function that is able to change the optical signal amplification feature variously, which is followed by user’s driving embedded pump LD freely. The output power of eash pump LD can be controlled separately by the program that is set up by user. When an optimum optical signal amplification particularity is needed, it is made up so that it can be materialized by choosing the Default mode provided along with User mode. More stable application of EDFA is possible through the monitoring of the factors such as in/out signal power, gain, alarm status and pump LD enabled by the application of FPGA processor which makes high speed driving possible. It is also set up that user’s present-time monitoring and control through LCD monitor of system main frame or GUI display for remote control can be possible. Through optimization of amplifier gain, noise figure, and saturated output power, this EDFA module will expand test capabilities in systems, components or sub-assembly manufacturing.
-
-
product
1.5µm PM Ev-Yb Fiber Amplifier ( PM EYDFA )
HAPM5000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM5000 is a C-Band Polarization Maintaining Optical Amplifier which worked in 1540~1570nm operating wavelength. Adopt Polarization Maintaining (PM) Multiclad Ev-Yb fiber, output optical power range 27~37dBm(0.5W~5W) ， extinction ratio >20dB.
-
product
Handset Power Amplifiers
Broadcom Handset Power Amplifiers support different operating modes (CDMA, UMTS, LTE, and GSM/EDGE) and multiple frequency bands offering premium performance in a very small form factor.
-
product
Power Amplifier
2734
The 2734 is a compact class D power amplifier, intended for acoustical measurements in the field or laboratory. All controls and connectors are placed on the front panel, enabling you to set up the 2734 very quickly, and to operate it in horizontal or vertical position. The 2734 is built into a robust flight case making it safe and easy to carry along.
-
product
Erbium Doped Fiber Amplifier
EDFA
Optoplex designed and produced high power single-mode and polarization-maintaining EDFA, which met MSA compatible requirements. C-band MSA EDFA Module with +23 dBm Output Power is Optoplex standard product. Optoplex designed Pre-EDFA provides more than 35dB gain with -40dBm input power. The Double-Cladding pumped EDFA produces 2W output power.
-
product
PXI Strain Gauge Simulator Module 4-Channel, 1.5k
40-265-404
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
Fuel Injection Pressure Tester with 2 Gages
33950
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Test all Ford vehicles with multi-port fuel injection systems.Includes two gages: Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR) and Small Gage for lower pressure requirement 0-50 PSI (0-3.5 BAR).
-
product
Bridge Amplifier
90376
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
product
Scaling Amplifier
SIM983
Stanford Research Systems, Inc.
The SIM983 Scaling Amplifier provides fine adjustable gain and offset control for analog signals. Both gain and offset are set with 3½ digits of resolution, and the signal path has more than 1 MHz of bandwidth.
-
product
Rack Mount Type Amplifiers
Amplifiers for each of O-, S-, C- and L-bands– Compatible with high-speed transmission (up to 100 Gbps)– Available for all signal types and protocols– Compatible with transmitters from all manufacturers– Compatible with SNMP
-
-
product
Saluki SPA Series Solid State Power Amplifier (max. 23KW output power)
Saluki SPA series is a solid-state RF power amplifier with an output frequency of maximum 110GHz and an output power of a maximum of 23000W. Its design is based on the most advanced GaN technology in the industry, and its power output is efficient and reliable. The product has functions such as temperature and current detection, alarm protection and so on.The broadband solid state power amplifier is mainly used for testing and measuring instruments, Communication or interference, aviation control and other fields.*Customization Available*
-
product
PCI & PXI Signal Amplifiers
Low power supply rails, a main part of the PXI, cPCI and PCI equipment, are a common cause for an inability to produce high voltage output. Tabor Electronics’ new amplifiers convert the supply rails to higher voltage suitable for signals up to 40Vp-p, thus solving thit problem.
-
product
Fracture Mechanics Clip-On Gages
Model 3541
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
GaN 100W Power Amplifiers
PE15A5033F
The PE15A5033F is a 100 W high gain Class A/AB Coaxial Linear Power Amplifier operating in the 0.7 to 2.7 GHz frequency range. The amplifier offers 100 Watts typical saturated power and 45 dB minimum small signal gain with 1.5 dB typical gain flatness @ Psat. The amplifier requires typically a +30V DC power supply. The SMA connectorized module is unconditionally stable and operates over the temperature range of 0C and +50C. The unit comes with a Heatsink and Fan.
-
product
Lock-in Amplifier
HF2LI
The Zurich Instruments HF2LI (high-frequency, 2 inputs) is a digital lock-in amplifier covering the frequency range between DC and 50 MHz. It features 2 physical input channels so that it can replace 2 devices in many measurement setups. The 128-bit digital signal processing delivers superior precision thus boosting both the noise performance and the dynamic reserve. With these unprecedented capabilities, the HF2LI brings lock-in amplification to a new level and enables new applications in a frequency range that was previously tied to analog instrumentation. The computer is connected by a high-speed USB interface, which allows data acquisition at high rates. The HF2LI is delivered with a fully featured graphical user interface and a choice of programming interfaces that greatly add to the usability of the instrument.
