Additive White Gaussian Noise
-
Product
Noise Testing Software
GN-1100 Series
-
This software has a comparator function for abnormality diagnosis based on sound/vibration analysis.You can perform simultaneously the tracking analysis and pass/fail judgment for 2 revolution input channels.It is ideal for vibration analysis of CVT and in-line 100% inspection such as carrier noise analysis of motors.
-
Product
Laser-Pumped White Light Source
LS-WL1
-
Our LS-WL1 is a laser-pumped white light source with a light output of up to 440 mW from a 600-µm fiber and a wavelength range of 450 – 700 nm, designed especially for professional requirements for extremely high luminance.
-
Product
Forward Path NPRT 2200 Noise Power Ratio Test Set
NPRT 2200-F
-
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
Product
Low Noise, High Performance, FTTP High Power Multi-port Optical Amplifier with a Gain Spectrum Band
MX5800 Series
-
Each output port for the optical amplifier has built-in high performance CWDM. Every external up-link optical port of the optical amplifier can conveniently connect with an OLT. Each of the 1550nm (CATV)’s output optical ports will multiplex 1310/1490n’s data stream from an external OLT, reducing the quantity of the components and improving the performance and reliability of the system.
-
Product
Ultra-Low Noise Filter, 42 V / 105 MA, 50 Ω
N1298B
-
The N1298 Series is a collection of low noise filters for the Keysight B2960 Series 6.5-digit low noise source.
-
Product
Low Phase Noise Amplifiers
-
Low Phase Noise amplifiers are critical for many applications requiring high signal integrity. This is especially relevant in instrumentation, defense, and telecommunication applications where low phase noise amplifiers are becoming increasingly important as the oscillators improve. Phase noise is described as the close-in noise to the carrier that can often appear as jitter on a clock signal. Analog Devices offers a large portfolio of low phase noise amplifiers to meet a variety of requirements in the LO network, receiver, as well as in the transmitter. Our portfolio supports a wide range of power levels and frequencies to provide the right solution for the given application.
-
Product
Additional Products: High Voltage 37 Pin D-Type Cables - Connector to Unterminated
Cable Assembly
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Signal, Patchcord, ITA, 72", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
7-103922000-072
Signal Patchcord
Signal, Patchcord, ITA, 72", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
-
Product
Environmental Noise Monitoring System
E-Box LITE
-
When you need to perform unattended noise measurements that are to be left outdoors, the very last thing you need is the hassle of complicated equipment.
-
Product
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
7-104962000-036
Signal Patchcord
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG White, Single Ended ( 5 Amps).
-
Product
Low Noise Accelerometer Cables & Coaxial Sensor Cables
-
Our cable assembly team in the UK produce the highest quality cable assemblies for use with a wide range of sensing and measurement applications. By making the cable assemblies in our own factory we are able to ensure the quality of every connection and every assembly, each cable is fully tested and its capacitance checked. Due to our experience in signal conditioning we understand the critical elements to quality signal analysis, this includes the correct cable. This is particularly true for accelerometer cables and sensors cables which can introduce significant noise issues if not used correctly.
-
Product
Noise Legislation Assessment Kit - Sound Meter And Dosemeter
05NK006
-
This system provides you with everything you need for noise risk assessments for noise legislation in one small package. A sound meter, dosemeter and calibrator kit featuring projected daily noise exposure from one short measurement and true peak for monitoring peak action levels.
-
Product
Additional Products: 100 Pin 1.27mm Pitch Micro-D Cables - 100 Pin To 100-Pin
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Advanced Low-Frequency Noise Analyzer
E4727B
-
Get a deeper, closer look at low frequency noise with the A-LFNA integrated with WaferPro Express, featuring data analysis, wafer prober control and test suite automation.
-
Product
Signal Patchcord, ITA, Mini Power, 50u Gold, 36", 14 AWG White Teflon, Single Ended, (40 Amps)
7-239912000-036
Signal Patchcord
Signal Patchcord, ITA, Mini Power, 50u Gold, 36", 14 AWG White Teflon, Single Ended, (40 Amps)
-
Product
Small Device Noise Emission Test System
-
The Small Device Noise Emission Test System from VIacoustics is a turnkey solution for the measurement of noise emissions of small devices typically used in computers, consumer electronics, appliances and automobiles. The system includes all hardware and software necessary (see the components tab) for the determinations of sound power levels (1/3 octave band and A-weighted), emission sound pressure levels (normalized 1/3 OB, A-weighted and high resolution FFT) and *ISO 532B loudness. The system is designed to be operated by a technician for production level testing or to be used by an engineer in the product development process.
-
Product
Low Noise Triple Band Voltage Controlled Oscillator
-
This Low Noise Triple Band Voltage Controlled Oscillator was designed to meet a specific customer requirement. The VCO cover the 3300 to 4700 MHz frequency range in three bands. The output power is +9 to +12 dBm with an integrated buffer amplifier to minimize load pulling. The three bands are selected using standard TTL control.
-
Product
Additional Products: 160 Pin DIN 41612 Cables - Connector To Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Signal, Patchcord, ITA, 72", QuadraPaddle, 22 AWG White Twisted Pair, Single Ended ( 5 Amps)
7-121422000-072
Signal Patchcord
Signal, Patchcord, ITA, 72", QuadraPaddle, 22 AWG White Twisted Pair, Single Ended ( 5 Amps).
-
Product
Noise Monitoring System
Harmony
-
A system that consists of automatic noise measuring device, transmission device, computer system, and operation analysis software, and provides accurate data necessary for establishing noise-related policiesby providing real-time information such as noise level, location, and device status for each branch.
-
Product
Low Noise Super Wide Band Amplifiers
WBA Series
-
WBA series low noise amplifiers have the octave bandwidth from MHz to GHz. With super low noise figure and exceptional low VSWR, WBA series LNA achieves exceptional gain flatness accross octave or multi-octave bandwidth.
-
Product
Additional Products: Standard Voltage 9 Pin D-Type Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Additional Products: 15 Pin D-Type Cables - Connector to Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Environmental Noise Monitors
-
Noise is one of the most complained about aspects of the environment, as not only does it have the potential to affect quality of life, it can also be difficult to monitor and therefore control. This type of noise is generally called environmental noise. There are many man-made sources of environmental noise, such as wind turbines, industrial sites, roads and traffic etc. If you are looking for equipment to measure noise in the workplace, look at sound level meters.
-
Product
Low Noise Amplifier (DC Powered)
-
RF Lambda’s DC low noise amplifiers (LNA) are broadband and offer low noise figure high IP3. Hermetically sealed options are available upon request.
-
Product
SCB-100 Noise Rejecting, Shielded I/O Connector Block
776990-01
Terminal Block
100-Pin Female SCSI to 100-Pin Female Screw Terminal, Desktop Mount Terminal Block - The SCB-100 is a shielded I/O connector block for interfacing I/O signals to NI data acquisition devices with 100-pin connectors. Combined with the shielded cables, the SCB-100 provides rugged low-noise signal termination.
-
Product
Low Noise Test Cables For N1413 With B2980 Series, 3m
N1427B
Coaxial Cable
The N1427B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1427B to the B2985B/87B.
-
Product
Noise Consultants Assessment System With 1/1 & 1/3 Octaves Class 1
01NK111/112
-
This Noise Assessment System can be configured to your exact requirements, making it the ideal product for Noise Consultants who perform a wide variety of noise assessments for industrial and environmental noise.
-
Product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
-
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
Product
Additional Products: 20 Pin GMCT Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
