Showing results: 4651 - 4665 of 5012 items found.
-
Kasuga Denki, Inc.
The electrostatic resistance of electronic devices is declining, and the number of ionizers installed is increasing. Ionizers cause deterioration of static elimination performance and imbalance of ions due to dirt and wear of the discharge electrode needle. Charging of electronic devices is also caused by ion blow. of an ionizer that is out of balance due to dirt and wear, and reaches a level that destroys advanced electronic devices.The atmospheric ion monitor measures the potential of the charging plate (detector), which has almost the same capacitance as the device's ground capacitance , with high accuracy, and is the most suitable measuring instrument for checking the effect when installing the ionizer and for daily management.
-
MPS-5 Series -
Matrix Technology Inc.
The five-channel programmable DC power supply is a new generation of high quality programmable linear DC power supply. The five channels can independently adjust the voltage and current. This series of products are equipped with RS232 communication interface, which has both desktop and system characteristics, and can be arbitrarily matched with other instruments, integrated as a test system with special functions to complete the measurement requirements in different occasions. The Upper computer program can be edited through the communication protocol, which brings great convenience to the user. It is a replacement product of the ordinary programmable power supple and has a high cost-effective advantage.
-
DtifEasy Series -
Marvin Test Solutions, Inc.
DtifEasy is a full-featured tool set for importing, converting, and executing IEEE-1445 compliant digital test vectors generated by a LASAR simulation. All four IEEE-1445 file types - UUT model group, Stimulus and Response group, Fault Dictionary group, and Probe group are supported by DtifEasy; providing the user with the ability to execute go/no-go, fault dictionary, and guided probe sequences. DtifEasy supports MTS' 3U PXI GX529x series of dynamic digital instrumentation to 200 MHZ as well as the 6U PXI GX5960, 50 MHz digital instrumentation. All of these instrument families are compatible with the digital logic probe.
-
NI
PXI Analog Output Modules support both static and software-timed voltage output applications. Modules also include 5 V TTL/CMOS digital I/O lines. Some PXI Analog Output Modules can deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. These advanced features enable you to use the PXI Analog Output Module to replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators.
-
72-7770 CAL DU -
Tenma
The 72-7770 CAL DU from Tenma is a palm sized digital multimeter with 3 3/4 digit LCD. It is 3 1/2digits with steady operations, fashionable design and highly reliable hand held measuring instrument. The meter measures AC/DC voltage, AC/DC current, resistance, temperature, diode and continuity. It is an ideal tool for maintenance. The multimeter features square wave output, data hold, low battery indicator and display backlight, This meter complies with the standards CE, IEC61010, in pollution degree 2, overvoltage category (CAT I 600V, CAT II 300V) and double insulation.
-
72-7770 CAL D -
Tenma
The 72-7770 CAL D from Tenma is a palm sized digital multimeter with 3 3/4 digit LCD. It is 3 1/2digits with steady operations, fashionable design and highly reliable hand held measuring instrument. The meter measures AC/DC voltage, AC/DC current, resistance, temperature, diode and continuity. It is an ideal tool for maintenance. The multimeter features square wave output, data hold, low battery indicator and display backlight, This meter complies with the standards CE, IEC61010, in pollution degree 2, overvoltage category (CAT I 600V, CAT II 300V) and double insulation.
-
IMADA, Incorporated
Imada digital force gauges are highly accurate instruments that provide the precise force measurement required in quality testing that determines strength and/or functionality of a part or product. Digital gauges can be used for destructive or non-destructive force measurement applications and check both compression and tension (push or pull) forces. The high sampling rate of Imada digital gauges enables them to capture the peak force of destructive tests which occurs in milliseconds. Imada digital force gauges also feature selectable units: lbf, kgf and N and easy-to-program high/low setpoints for Go/No Go testing.
-
OTP2 module no.186 -
LXinstruments GmbH
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Kyoritsu Electrical Instruments Works, Ltd.
New technology permits safe testing, without the need of direct contact between probes and live wires. The insulated crocodile clips can clip insulated cables from 2.4 to 30mm. Phase rotation is indicated by the rotary illumination of LEDs and logical audible tones. The instrument can be fixed to a metal panel via the magnet on the back side. Wide measuring range for 3 phase installations from 70V to 1000V AC. Super brightness function permits clear LED''''s indication also in sunshine. Complies with IEC 61010-1 CAT IV 600V and CAT III 1000V.
-
Rinch Industrial Co.,Limited
Application of ultrasonic flaw detector : It can not only be used in lab but also can be used on engineering site. Also, it can be widely used for safety checking and life evaluating in fields of aeronautics, rail transportation and boiler pressure vessel, it can used to test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in work piece’s interior swiftly and accurately without any destruction. It is widely used for flaw detecting in fields of power engineering , boiler pressure vessel , Steel Construction , war industry , aeronautics , rail transportation ,auto and machinery etc. It is the essential flaw detecting instruments in NDT industry.
-
A10-M -
Quartzlock (UK) Ltd.
Frequency Referencing, Calibration, Standards Lab, Production Test for Oscillator Manufacturers. A very high stability LOW NOISE 10MHz Rubidium Reference, primarily for production test of quartz oscillators and RF instrumentation frequency referencing. This industry standard 2U rack-mount instrument has a long heritage and ongoing production life for this latest 2009 version that features RS232 monitoring and control of the DPLL, locking the Ultra Low Noise OCXO to the Rubidium. Damping and Bandwidth is controlled by integrator digital gain, proportional digital gain, pre-filter order and subsample rate. Eight values of user selected bandwidth are available.
-
FiberPal OT-8700 -
Radiantech, Inc.
FiberPal OT-8700 series instruments, with power meter built-in, are new miniature, high performance optical time domain reflectometer which is designed as fiber troubleshooter for locating fiber connector, break and imperfections for access networks. It detects event locations along the optical fiber and displays the results on a 7” color LCD display. FiberPal OT-8700 series are light, reliable and easy to use, hence it is ideal for FTTX testing. The Application Software equipped is used for data analysis, processing and storage. With the USB Interface port, enabling FiberPal OT-8700 series to transfer test data to computer easily.
-
HISAC Swift -
Scope T&M Pvt, Ltd.
HISAC Swift - Circuit Breaker Operational Analyser is meant for checking the performance of the MV Circuit Breakers. The Analyser contains various intelligent measuring modules designed for measuring parameters such as contact timings of Main/PIR & Auxiliary contacts, Close/Trip Coil Current characteristics and Static Contact Resistance of R, Y & B poles simultaneously. The results can be directly viewed on the TFT touch screen display in graphical as well as numerical form. It is possible to print the graph on a built-in thermal printer or download record to PC for further analysis on CPLOT software. This all in one instrument is best suited for gang operated CBs.
-
450 -
Oersted Technology
The Model 450 is a high-resolution, laboratory gaussmeter, capable of measuring magnetic fields from 0.001 Gauss to 300k Gauss (measurement range is dependent on probe used). This unit is designed for demanding applications, such as material analysis and field mapping, where low-noise, high-resolution magnetic measurements are necessary. Measurements of AC and DC magnetic fields are shown in Gauss or Tesla on the two-line vacuum fluorescent display. The Model 450 features RS232C and IEEE-488 ports, allowing the instrument to be controlled via a remote computer or automation equipment. A hall-effect gaussmeter probe is included with the Model 450, and may be selected from an extensive line of probe
-
SolarWinds
One of the most important measurement tasks in radio engineering is the analysis of electrical circuits. A network analyzer is an instrument that is designed to solve this problem with high accuracy and efficiency. The circuits that can be analyzed with network analyzers have a wide range of applications ranging from simple devices such as filters and amplifiers to complex modules used in communications satellites. PLANAR specializes in the development and production of vector network analyzers that combine the capabilities of scalar network analyzers that measure not only the amplitude components of the main characteristics of the system (gain, loss, standing wave ratio, etc.), but also allow measurements of the amplitude and phase characteristics of the system .
