Conductance
See Also: Battery Conductance Testers
-
Product
Ultrasound Leakage Tester
-
Measures both the conductivity of the cleaning medium and the leakage current of the ultrasound transducer.
-
Product
Conductivity Type Tester
HS-HCTT
-
It is strictly designed according to the requirements of the hot-probe thermal EMF conductivity type test in standard ASTM F42: Standard Test Methods for Conductivity Type of Extrinsic Semiconductor Materials. A temperature controlling heating element is installed inside the hot probe so that the hot probe is heated automatically and its temperature is maintained in the range 40-60℃.
-
Product
PXI High Density MUX BRIC, 96-Chan, 10-Pole
40-570-416
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Online Conductivity Controller
LD-LOCC-A10
-
Online Conductivity ControllerLD-LOCC-A10features 3 points conductivity calibration system, TDS measurement mode, and 4 to 20 mA output signal transmitter. The large and clear back light LCD displays Calibration and setup values, Temperature values, ATC (automatic temperature compensation) values, high and low limit of measurement. This controller measures Conductivity and TDS values in µS/ cm, and mS/ cm units.
-
Product
Electrodes
-
Electrodes are offered in a wide variety of types. Spring electrodes are normally used in the inspection of pipes, although circular brush electrodes can also be used. Flat brush electrodes are used for flat surfaces. Brush materials can be of brass, steel or conductive neoprene construction. Internal electrodes are for testing internal pipe coatings.
-
Product
Storage Modules
-
Elma offers the most complete line of storage modules in the embedded computing industry. Board sizes include 3 U, 6 U, mezzanine and small form factors in VPX, VME, CompactPCI, PMC and XMC standards. Environmental capabilities address commercial and rugged applications with SSDs (solid state drives) and rotating drives (HDD) and surface mount NAND flash. Choose from features including RAID, front panel removability, high capacity conduction cooled mezzanine storage, secure erasure or write protection.
-
Product
Safe Discharge Rods
-
These instruments will allow you to conduct the safe damp discharge of the residual charge on the cable / equipment by limiting the discharge current.
-
Product
PXI 3A Power MUX BRIC, 32-Channel, 6-Pole
40-571-404
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Environmental Noise Measurement Kits
-
Environmental conditions can significantly impact the accuracy of sound level measurements, particularly when conducting assessments in outdoor environments, so this is where an Outdoor Environmental Noise Kit can help you. The kit provides a fully weather-protected system for outdoor noise measurement to protect your sound level meter and microphone from harsh weather conditions, ensuring reliable and accurate readings in any environment for up to 1 week.
-
Product
DX4015
-
The DX4015 empowers professionals to monitor gases in environments that have typically been challenging to conduct measurements. Thanks to its heated sample cell, the DX4015 can be used in humid conditions – with exceptionally low detection limits.
-
Product
FTIR Analysis
-
Anton Paar offers state-of-the-art Fourier-transform infrared (FTIR) instrumentation with the possibility to automate and connect to other Anton Paar benchmark instruments. It combines FTIR spectroscopy with comprehensive data analysis to provide rapid results and increase efficiency in the laboratory. A high-resolution touchscreen with a user interface inspired by modern smartphones enables operators to conduct the most intuitive FTIR analysis available on the market. Anton Paar’s FTIR specialists and a worldwide service network are ready to support you with your spectroscopy applications.
-
Product
VPX High Power
VPX 371
-
WIENER VPX power supplies are commercial off-the-shelf (COTS), conduction cooled single stage converters according to the ANSI/VITA 62.0 specification. They can be used to power a VPX chassis and will fit into the standard envelope defined by VITA 48.0 specifications.
-
Product
Process Analyzers
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Industrial meters for pH, ORP, conductivity and oxygen. In 2- and 4-wire technology, explosion-proof.Bus Communication: HART, FOUNDATION Fieldbus, Profibus DP and PA. Robust industrial housing with high IP protection. Suitable for outdoor use. For analog and digital sensors. Simple intuitive operation. From DIN rail transmitters up to the modular system.
-
Product
Field-installation Type Electric Conductivity Meter (Two-Wire Transmission, For Low-concentration)
HE-300C
-
HE-300C connects conductivity sensor (ESH/FS Series) and measures conductivity and temperature in the sample water. It is suitable for monitoring pure water/boiler water drainage recovery control and inline measurement of pharmaceutical water conductivity according to USP<645> quality guidelines.
-
Product
Self-testing Static Grounding Clamp
Bond-Rite CLAMP
-
In many branches of the process industries, fires and explosions can result from electrostatic discharge in hazardous areas. Even relatively small sparks have sufficient energy to ignite many flammable vapours, gases and even airborne dusts. In situations, where this risk exists, static grounding (earthing) and bonding clamps are required wherever mobile or portable conductive plant items (such as drums and vessels etc) are used.
-
Product
Handheld Gas Detection Meter
GT-Fire
-
Teledyne Gas & Flame Detection
The GT-Fire is a dedicated hand-held gas detection meter specialized for the fire industry.It provides the confidence and assurance required by fire fighters when called to safety-critical environments.The GT-Fire enables gas detection to be conducted via one instrument in a complete, professional and timely manner, with easy access to data simplifying the reporting process.
-
Product
Process Automation
-
At GF Industry and Infrastructure Flow Solutions, we provide comprehensive solutions for your processes, focusing strongly on manual and actuated valve, and measurement solutions such as flow, pH/ORP, conductivity, temperature, pressure, level, dissolved oxygen (DO), free chlorine as well as monitors, transmitters and controllers for the safe management of your liquid processess.
-
Product
Human Potential Measuring Instrument
KSD-4000 / KSD-4100
-
Electronic devices and metal tools carried by workers have individual capacitance to ground and are charged at human potential. When the charged electronic device touches the ground or a metal tool touches the electronic device, a transient current with a high peak current flows at high speed, Causing A Failure. By Using The Human Body Potential Measuring Device, The Potential Of The Human Body Can Be Measured Accurately, And It Can Be Immediately Determined Whether Or Not The Electronic Device Is Damaged By The Potential. You Can Also Find Out How Much Static. .. .electronic meters such as conductive floors, electrostatic mats, electrostatic shoes, and wrist straps reduce the human potential.
-
Product
Thermitest
THW-L2
-
Designed with speed and operational simplicity in mind, the Transient Hot Wire (THW-L2) Liquid Thermal Conductivity Meter is an advanced measurement system for direct determination of the thermal conductivity of liquids and pastes in accordance with ASTM D7896-19. In less than 2 seconds, a single measurement of small volumes of liquids and pastes can be accurately and precisely measured for thermal conductivity. Using a non-stationary measurement approach, the THW-L2 uses rapid test times to limit convective effects for samples with a wide range of viscosities. The THW sensor consists of a 60 mm heating wire that is fully inserted into an isothermal sample. A constant current source (q) is used to heat the sensor wire and the temperature rise is recorded by monitoring the change in electrical resistance of the wire. The slope (m) is determined from the plot of temperature rise vs. logarithm of time and is used in the calculation of thermal conductivity (λ). Liquid samples of high thermal conductivity will have a lower slope, while liquid samples with low thermal conductivity will have a higher slope.
-
Product
Coupling Decoupling Network
TBCDN-M2
-
The TBCDN-M2 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6.
-
Product
PXI High Density MUX BRIC, 40-Chan, 20-Pole
40-570-315
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Near Field Probes 1GHz - 10 GHz
SX set
-
The SX1 set consists of 3 passive near field probes for making measurements in the development phase of E-field and magnetic field with a high clock frequency in the range from 1 GHz to 10 GHz. The probe heads of the set SX allow for measurements close to electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors, to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through trained use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
Product
Digital Conductivity Pen (EC)
CD601
-
The Milwaukee CD601 digital electrical conductivity (EC) Pen is designed for aquariums, aquaculture, pools, water conditioning and many other applications. The CD601 helps you make sure that your water has the right amount of nutrient to help keep fish tanks healthy or helps you keep your filters up-to-date and clean for water filtration. Keep EC in your target range to help your achieve better results.
-
Product
Photometry
-
Photometric equipment is one of our main activities. Two distinct areas are involved - Industrial, Commercial, Road Lighting is one, while Automobile Lighting is another. Photometric equipment areused to conduct tests on Lamps, Industrial Lighting, Street Lighting,Automotive Lighting & related products. Most Photometric equipment are custom built to suit specific customer requirements.
-
Product
Oil Content Analyzer
OCMA-500
-
OCMA-500 to measure concentration of oil contained in drainage and environmental water.After injecting the water sample and solvent, all you have to do is press the start button,and the system will automatically conduct the monitoring operation from oil extraction to sample measurement and draining. With no more troublesome operations like opening/closing the drainage valve, monitoring is speeded up.In addition, the color graphic LCD and the backlit extraction tank have improved operability.
-
Product
Charge Logger Sensor
NUL-246
-
This sensor measures electrostatic charges. It can be seen as a highly sensitive electroscope indicating whether a charge is positive or negative. Other uses are: to explore the nature of static charge, to measure both charge and voltage, to measure charge by induction, quantify the charge on a capacitor or discover the charge distribution on a conducting sphere.
-
Product
Application Specific LC Systems
Nexera Organic Acid Analysis System
-
The Nexera Organic Acid Analysis System has been well-received in the fields of food and environment as a highly selective high-sensitivity system. It uses separation by ion exclusion chromatography and Shimadzu’s unique detection technique (pH-buffered electric conductivity detection). Recently, this system is being utilized by even more users in a wide variety of fields, and its usage in the fields of pharmaceuticals and life science is increasing.
-
Product
pHmeter-Conductivity-Thermometer Data Logger
HD2156.2
-
pHmeter-Conductivity-Thermometer measures pH, mV, conductivity, liquid resistivity, total dissolved solids, salinity and temperature. Datalogger, stores the maximum, minimum, average value and can store up to 20,000 sets of three measurements.
-
Product
PH Meters, Water and Oil Testers
-
PeakTech Prüf- und Messtechnik GmbH
To measure the conductivity value (ranging from 0 - 2000 µS) which can therefore judge whether water is pure or not. The conductivity value will become lower if there is much less impurities existed in water (for example, distilled water that its purity is higher than others will get a lower conductivity value of approx. < 10 µS). In industrial sectors, it would be a great help for the quality of the products if using the good water (more pure water) in the process. It may cause several diseases if home drink water existing high conductivity & contain impurities, the (pure water tester) are designed to check the purity of water (water conductivity) also can determine the conduction of the “water filter” easily and rapidly.
-
Product
Ring Wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Ring wave interference on electronic line, control line and signal line can be caused by transient due to switch of mains and controlled switch or lightening strike. RWS 600 is designed to conduct immunity test for electronic and electrical device.
