-
product
Swing Mill for Sample Sizes 2 - 100 Grams
Disc Grinder 8500
Ring & Puck mill that accommodates sample sizes ranging from 2 - 100 grams. Ideal for pulverizing dry, brittle samples and slurry grinding.
-
product
cDAQ-9189, 8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785065-02
8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9189 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly distributed measurements over long distances. The chassis has an integrated network switch for simple daisy-chaining. The chassis also has four 32-bit general-purpose counters/timers, accessible through a hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, pulse train generation, and more.
-
product
Portable Ethernet Testers
Portable Ethernet Testers are widely used to test the performance, function, and quality of Ethernet and IP network systems by generating and validating traffic patterns.
-
product
Handheld Oscilloscopes, 100 MHz, 2 Analog Channels
U1610A
100 MHz2 analog channelsTroubleshoot in any weather with channel-to-channel isolation and a CAT III 600 V safety ratingIdentify glitches easily with dual window zoomView subtle signal details more clearly with up to 1 Gsa/s sampling rate and 120 Kpts memoryDebug under any lighting conditions with 3 selectable viewing modes (indoor, outdoor and night vision)Get 3 instruments in 1: a dual-channel oscilloscope, built-in DMM and data loggerEasier start-up with 10 selectable languages
-
product
Multibus Ethernet Card
MS 1750
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz- SDRAM Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Multibus Interface- Serial Interfaces: Up to four external UARTs- CAN 2.0B controller- Three I2C ports- Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements
-
product
Dual-Port 25GbE PCIe Ethernet NIC
P225P
Based on Broadcom’s scalable 10/25/50/100/200G Ethernet controller architecture, the NetXtreme®-E Series P225P 2x25G PCIe NIC is designed to build highly-scalable, feature-rich networking solutions in servers for enterprise and cloud-scale networking and storage applications, including high-performance computing, telco, machine learning, storage disaggregation, and data analytics.
-
product
Ethernet Instrument & System Control Software Application
F-SIM-DCE
Avionics Interface Technologies
Simulation and Data Capture application for use with AIT’s Dual Channel Ethernet (DCE) and 10G Ethernet Instruments.
-
product
1 Channel 100 MHz Flash ADC
NIMbox ADNN
NIMbox ADNN - 1 channel 100 MHz flash ADC with 3 programmable TTL I/O ports, 4 LE discriminators and 10 NIM or TTL I/O ports
-
product
OpenVPX Ethernet I/O rear transition module.
EnsembleSeries™ RTM30P
*Companion Rear Transition Module for 3U OpenVPX Xeon® D-series process payloads (LDS3506)*Field Replacement Unit capability
-
product
LXI WTB Terminator, 100 ohm
60-983-001
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
product
Cable Assembly, 100 Pin Male SCSI to 100 Pin Male SCSI, Twisted Pair, Double Ended, 18"
515109134
Cable Assembly, 100 Pin Male SCSI to 100 Pin Male SCSI, Twisted Pair, Double Ended, 18"
-
product
Automotive Ethernet Tools
Automotive Ethernet (AE) represents the latest challenge to the status quo in automotive networking. Many OEMs are now moving forward with this exciting new technology, which promises high performance at low cost, especially for infotainment applications. Capturing Automotive Ethernet Frames. Automotive Ethernet traffic cannot be monitored using the same techniques employed for buses like CAN. Ethernet networks use star topology, so there is no single point to monitor an entire network. The sophisticated technology employed also means bit values cannot be interpreted directly from voltage levels. Finally, Ethernet hardware silently discards erroneous frames, making diagnosing problem conditions difficult. Intrepid’s tools are designed to address all of these issues conveniently and efficiently.
-
product
IoT Ethernet I/O Modules
ADAM-6000/6200
Supporting Modbus & IoT protocols, Ethernet remote data acquisition modules offer analog, RTD, thermocouple, digital, relay and counter I/O.
-
product
RS232 / RS485 / RS422 / Ethernet Surge Protectors
Our passive, rugged, industrial-grade RS232 / RS485 / RS422 / Ethernet surge protectors are designed for direct industrial DIN-rail mounting and they come with two (2) or three (3) stages of surge protection — Gas Discharge Tube (GDT), protection resistors, and Transient Voltage Suppressor (TVS) - for maximum protection. From 2-wire RS485, 4-wire RS422 / RS485, to 10 / 100 / 1000M Ethernet, CommFront's surge protectors safeguard your data lines and provide you with a peace of mind.
-
product
Plus Radio Ethernet Receiver
ACSRF-4040
The Plus Radio Ethernet receiver is required as part of the Tinytag Radio Data Logging System. It controls the transmission of data to and from the radio loggers: data received from the loggers is then sent to the computer for viewing with Tinytag Explorer radio software. If power to the computer running the system is lost, the receiver has a battery back-up which will maintain the mesh network until power is restored. This receiver plugs directly into a LAN removing the need for a computer in the area where monitoring is to take place. The receiver is powered using a plug-in Power over Ethernet adaptor (ACS-0041) which is supplied with the unit.
-
product
PCI-5421, 100 MS/s, 16-Bit Waveform Generator Device
778692-02
The PCI‑5421 can generate user-defined, arbitrary waveforms and standard functions, including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms. The PCI‑5421 also features advanced synchronization and data streaming capabilities.
-
product
6-Port Hardened Industrial Gigabit Ultra PoE DIN-Rail Switch
TI-UPG62
4 x Gigabit Ultra PoE ports2 x dedicated SFP slots240 watt power budget12 Gbps switching capacityHardened IP30 rated metal switchIncludes DIN-rail and wall mountsExtreme -40 to 75 ºC (-40 to 167 ºF) operating temperature rangeDual redundant power inputs with overload current protectionAlarm output triggered by power failurePower supply sold separately (TI-S24048)
-
product
1 Channel 100 MHz Flash ADC
NIMbox DNAE
NIMbox DNAE - 1 channel 100 MHz flash ADC with 3 programmable TTL I/O ports, 2 channel DAC 100 MHz, 4 LE discriminators and 5 NIM or TTL I/O
-
-
product
Ethernet To Parallel Digital Interface Boards
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
product
Cryogenic Mill for Sample Sizes 0.1 - 100 Grams
Cryogenic Gringer 6870
Large cryogenic mill that accommodates sample sizes ranging from 0.1 - 50 grams. Specifically designed for cryogenic grinding and pulverizing tough and/or temperature sensitive samples immersed in liquid nitrogen. CE Approved.
-
product
ION 100 Portable Ion Meter
The new addition to the Environmental Express Oakton product line features updates to measuring water quality easier and faster. The larger LCD display is 2.75 in. by 2.0 in. for a better viewing angle, and has indicators for battery life, stability, and calibration. The ION 100 meter measures pH, mV, ion concentration of 16 commonly measured ions, and temperature. The microprocessor-based meter features automatic calibration, automatic temperature compensation, function setup, self-diagnostics, automatic power-off, and low voltage display. The meter uses advanced digital processing technology, intelligently improving the response time and accuracy of your measurements. Easily switch units among pX, mol/L, and mg/L (ppm).
-
product
Reach Power-over-Ethernet (PoE) Testers
After assembly, electronic equipment manufacturers need to test functionally of their products. They want to provide the most test coverage, in the shortest time, for the least cost. When test engineers develop product test plans, they select the most appropriate off-the-shelf general purpose test equipment available. Reach designs and manufactures custom test equipment which is a better fit than general purpose equipment. It not only reduces test time but also reduces costs.
-
product
VB-8012, 2-Channel, 100 MHz Bandwidth VirtualBench All-in-One Instrument
783555-04
2-Channel, 100 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8012 combines a two‑channel, 100 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interactive way to view all your measurements on a single screen and can be updated for free with software releases over time to continually add functionality and value to your VirtualBench. VirtualBench also tightly integrates with LabVIEW software to enable programmatic control and automated test sequences.
-
product
NI-9147, 4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis
783496-01
4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9147 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9147, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
product
Ethernet Controller ICs
CP220x
The CP220x family is the industry's smallest single-chip Ethernet controller containing an integrated Media Access Controller (MAC) and Physical Layer (PHY).
-
product
Ethernet Gateway
ICS's Model 9065 Ethernet Gateway is an Ethernet to GPIB Controller that connects easily to your computer's Ethernet port, company network or to the Internet to control GPIB instruments. The Model 9065 is VXI-11 compliant, does not require special drivers and is compatible with the following systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems. ICS's 9065 uses VXI-11 RPC calls for secure communication with virtually any computer. Eliminates the need for special drivers. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. See our extensive Application Notes or download our VXI-11 Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product.
-
product
E1 Ethernet cable, twisted pair 5m
182219-05
8-Pin Male Ethernet to 8-Pin Male Ethernet, CAT-5E Ethernet Cable - The 8M-8M Ethernet Cable connects devices to network hubs or switches. The cable has straight-through wiring and is available in different lengths and thin profile options.
-
product
8-port LAN Module With Intel® 82580EB Ethernet Controller
AX93316
Axiomtek's AX93316 LAN module is built with an Intel® 82580EB GbE Ethernet controller to optimize data traffic processing, employing advanced techniques including the Intel® DPDK, I/OAT, Jumbo Frames and VMDq, not only enabling network appliances to speed up their data traffic but also enhancing their packet processing capabilities for higher throughput of data.
-
product
cDAQ-9189, 8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785065-01
8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9189 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly distributed measurements over long distances. The chassis has an integrated network switch for simple daisy-chaining. The chassis also has four 32-bit general-purpose counters/timers, accessible through a hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, pulse train generation, and more.
