Op Amps
IC used as voltage amplifier. Also known as: Operational Amplifiers
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
product
Mini Power, Contact, Receiver, 65 Amp, 8 AWG
610116112
Primary mating contact 610115124. (May mate with other ITA contacts, as well.)Mini Power contacts carry up to 65 amperes continuous current. Maximum resistance is 1 Milliohms.Specifications Operating Current 65 Amps Max. Continuous – 8 AWG40 Amp Max. Continuous – 12 AWG30 Amp Max. Continuous – 14 AWG25 Amp Max. Continuous – 16 AWGContact Resistance 1 mOhms Max.Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 1000 MOhms Min.Contact Body BrassContact Plating 50µ" Au over 100µ" NiContact Termination SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 3.37
-
product
SparkFun Mono Audio Amp Breakout
TPA2005D1
This tiny audio amplifier is based on the Texas Instruments TPA2005D1. Its efficient class-D operation means low heat and long battery life. It can drive an 8-Ohm speaker at up to 1.4 Watts; it won't shake a stadium, but it will provide plenty of volume for your audio projects.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 2 Amp, 0.5m, 250 Port
A500RMR-T-5C050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Round Post
610138115
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body (RCV) – BeCu (Twin Female)BeCu/PhBrz (Crimp)Male (ITA) – BrassContact Plating Female (RCV) – 50µ” Au over 100µ” NiMale (ITA) – 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
Open Pluggable Specification (OPS) Digital Signage Player With LGA1151 Socket 8th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® H310 And TPM 2.0
OPS500-520-H
The OPS500-520-H is powered by the newest 8th generation Intel® Core™ i7/i5/i3 and Celeron® processors (code name: Coffee Lake S) with the Intel® H310 chipset. The smart cableless digital signage module has two DDR4-2400 SO-DIMMs for up to 32GB of system memory. Axiomtek's OPS500-520-H supports the LGA1151 socket-type processors offering greater flexibility for CPU selections, which is easily configured to meet various performance requirements. The OPS signage module is connected to OPS-compliant display via a standardized JAE TX-25A plug connector interface which supports DisplayPort, HDMI 2.0, USB 2.0, USB 3.1, audio and UART signals. It also has one M.2 Key E for Wi-Fi modules and one M.2 Key M supporting PCIe, SATA and SSD interfaces for storage. We believe that this new smart cableless open pluggable signage module with simplified installation, maintenance and upgrade can help you develop creative display solutions that increase your sales and improve your customers' experiences. With the enhanced multimedia performance, the Intel® Coffee Lake S-based OPS500-520-H is well suited for a wide range of digital signage applications in retail, transport, entertainment, education, and more.
-
product
High Amps, Contact, ITA, 500+ Amps, 350 MCM
610153102
High Amps, Contact, ITA, 500+ Amps, 350 MCMContact rated to 1500VDC for low duty test applications.Mating contact 610152101. (NOT compatible with other VPC contacts)Contact ONLY compatible with 410105174 ITA.
-
product
Signal, Contact, ITA, TriPaddle, 7 Amp, .025" Square Post for Wire Wrap
610110113
Primary mating contact 610110177. (May mate with other Receiver contacts, as well.)Plated with 30µ" gold.
-
product
Signal, Patchcord, ITA, 36", QuadraPaddle, 24 AWG White XLPVC, Single Ended (3 Amps)
7-121964000-036
Signal, Patchcord, ITA, 36", QuadraPaddle, 24 AWG White XLPVC, Single Ended (3 Amps).
-
product
3,000 AMP PORTABLE POWER SOURCE WITH JUMP START FUNCTION
Part No. VERSAPRO3
Shanghai Beha Electronics Co., Ltd.
*Multi-function portable power you can take anywhere*Designed to jump start cars, trucks, motorcycles, boats, ATV’s and more*Vehicle jump starting and device charging capabilities for all of your portable power needs
-
product
PCI 2 Amp Multiplexer, Single 16-Channel, 4-Pole
50-635A-003
The 50-635A-003 is a single 16-channel, 4-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI/PXIe Power Relay Module, 24xSPDT, 5 Amp, 50-Pin SGMC Connectors
40-158-002
The 40/42-158-002 is a PXI/PXIe high density power relay module with 24xSPDT switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
200 Amp AC Current Adaptor
DL6701
The DL6701 is a compact 200A AC current clamp adaptor with voltage output via standard 4 mm connectors. To be connected to a digital multimeter or other voltage measurement device.
-
product
Signal, Patchcord, ITA, 36", TriPaddle, 26 AWG White XLPVC, Single-Ended (1.5 Amps)
7-105966000-036
Signal, Patchcord, ITA, 36", TriPaddle, 26 AWG White XLPVC, Single-Ended (1.5 Amps).
-
product
PXI/PXIe Power Relay Module, 8xSPDT, 5 Amp, 50-Pin SGMC Connector, With Interlock
42-158-004-HI
The 40/42-158-004-HI is a PXI/PXIe high density power relay module with 8xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
product
Signal, Patchcord, Receiver, 72", QuadraPaddle, 22 AWG White, Twisted Pair ( 5 Amps)
7-124439000-072
Signal, Patchcord, Receiver, 72", QuadraPaddle, 22 AWG White, Twisted Pair ( 5 Amps)
-
product
48V / 200 Amp Load
EL12-48M
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely costeffective.
-
product
Signal, Patchcord, ITA, TriPaddle, 36", 26 AWG White, Single Ended (1.5 Amps)
7-105926000-036
Signal, Patchcord, ITA, TriPaddle, 36", 26 AWG White, Single Ended (1.5 Amps)
-
product
500-Pin SEARAY Cable Assembly, Male to Male, 1 Amp, 1m, 500 Port
A500RMR-500RMR-1B100
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
-
product
Microwave Wideband Direct Modulated DFB Transmitters (without RF Amp)
MT50 (40KHz~20GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MT50 series microwave wideband direct modulated DFB transmitter, are able to transmit 20G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc.
-
product
Open Pluggable Specification (OPS) Digital Signage Player With Intel® Core™ I7/i5/i3 Processor
OPS875
*Open Pluggable Specification (OPS) compliance*Socket G2 (rPGA988B) 3rd gen Intel® Core™ i7/i5/i3 processor*Intel® HM76 chipset*DDR3-1600 SO-DIMM, up to 8GB*2 USB 3.0 ports and 1 PCIe Mini Card slot*Pluggable HDD for easy maintenance*Easy to change DRAM*HDMI for 2nd display
-
product
PXI/PXIe Power Relay Module, 8xSPDT, 5 Amp, 37-Pin D-type Connector, With Interlock
42-158-104-HI
The 40/42-158-104-HI is a PXI/PXIe high density power relay module with 8xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 37-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp/Solder
610110125
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp/Solder.p/n 610110125 TriPaddle Receiver 50µ" AU platingp/n 610110101 TriPaddle Receiver 30µ" AU platingThis contact primarily used in CASS applications.
-
product
600A TRMS Clamp Meter w/ DC Amps, Inrush, Magnet
DL589
UEi Test & Measurement Instruments
True-RMS Dual Display 600A Clamp Meter w/ DC Amps & Differential
-
product
Power, Patchcord, ITA, Mini Power, 36", 14 AWG White Teflon, Single Ended, (30 Amps)
7-241914000-036
Power, Patchcord, ITA, Mini Power, 36", 14 AWG White Teflon, Single Ended, (30 Amps).
-
product
130 AMP Battery Load Tester
MD4370
Compact, ergonomically designed tester determines a battery's charge and tests batteries, starting, and charging systems.Powerful 130 amp load capacity provides more accurate test results.Uniquely designed clamps assure a positive connection on any style battery.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 1 Amp, 2m, 500 Port
A500RMR-C-1B200
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 1 Amp, 1m, 500 Port
A500RMR-C-1B100
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.
-
product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 0.5m, 250 Port
A500RMR-500RMR-4B050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
product
Mini Power, Receiver, 50u Gold (22 Amps). 18 AWG Twisted Pair Red/Black (5 Amps). Banana Plug Black, Banana Plug Red, 36"
7-245436673-036
Mini Power, Receiver, 50u Gold (22 Amps). 18 AWG Twisted Pair Red/Black (5 Amps). Banana Plug Black, Banana Plug Red, 36"
-
product
Signal, Patchcord, ITA, 72", TriPaddle, 22 AWG Twisted Pair, Single Ended ( 5 Amps)
7-103422000-072
Signal, Patchcord, ITA, 72", TriPaddle, 22 AWG Twisted Pair, Single Ended ( 5 Amps).
