Op Amps
IC used as voltage amplifier. Also known as: Operational Amplifiers
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 2m, 250 Port
A500RMR-C-5C200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
Signal, Contact, ITA, TriPaddle, 7 Amp, .025" Square Post for Wire Wrap
610110113
Signal Contact (ITA)
Primary mating contact 610110177. (May mate with other Receiver contacts, as well.)Plated with 30µ" gold.
-
Product
PXI 16 Amp Power Multiplexer, Single 12-Channel 1-Pole
40-662A-014
Multiplexer Module
The 40-662A-014 is a single 12-channel, 1-pole MUX and is part of our range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 0.5m, 250 Port
A500RMR-500RMR-4B050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
Product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin D-type Connector
42-158-103
Relay
The 40/42-158-103 is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A. User connection is via a 50-pin D-type male connector.
-
Product
Single 8x2 1-Pole 16 Amp PXI Power Matrix
40-552-002
Matrix Switch Module
The 40-552 range of 16 Amp PXI power matrix modules is available in four configurations with matrix sizes of 8x2 and 4x4 and the ability to expand the matrix size with the Y-Axis loop-thru connections: e.g. 8x4, 12x4, 16x4, etc. (with 4x4 matrices) or 16x2, 24x2, 32x2, etc. (with 8x2 matrices). This range is capable of switching up to 16 Amps and up to 300VDC/250VAC hot switching and 400VDC/250VAC cold switching. These PXI power matrix modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors, and solenoids.
-
Product
Power, Patchcord, Receiver, 36", Micro Power, 14 AWG White, Single Ended ( 22 Amps)
7-252914000-036
Power Patchcord
Power, Patchcord, Receiver, 36", Micro Power, 14 AWG White, Single Ended ( 22 Amps).
-
Product
PXI/PXIe Power Relay Module, 8xSPDT, 5 Amp, 50-Pin SGMC Connector
40-158-004
Relay
The 40/42-158-004 is a PXI/PXIe high density power relay module with 8xSPDT switches rated at 5A. User connection is via a 50-pin SGMC male connector. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
Tool, Crimp, TriPaddle (10 amp), Thermocouple, Micro Power, Receiver and ITA , Locator Required
910101102
Crimp Tool
This crimp tool can be used to crimp 10 Amp TriPaddle contacts, Thermocouple contacts or Micro Power contacts. Locator required.
-
Product
Power, Patchcord, ITA, 72", Micro Power, 14 AWG White, Single Ended ( 22 Amps)
7-251914000-072
Power Patchcord
Power, Patchcord, ITA, 72", Micro Power, 14 AWG White, Single Ended ( 22 Amps).
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 1 Amp, 1m, 500 Port
A500RMR-C-0A100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products). Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
PXI 25 x SPST Reed Relay 2.5 Amp
40-136-111
Reed Relay
Pickering Interfaces 40-136 Power Reed Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. The 40-136 is suitable for voltages to 200V and current to 2.5A. Available in Normally Open (SPST & DPST) configurations. Connections are made via a front panel mounted 50 or 78-pin D-Type connector.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 1 Amp, 1m, 500 Port
A500RMR-500RMR-0A100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
-
Product
PXI 2 Amp Multiplexer, Single 16-Channel, 4-Pole
40-635A-003
Multiplexer Module
The 40-635A-003 is a single 16-channel, 4-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Signal, Contact, Receiver, TriPaddle, 10 Amp, 14-18 AWG
610110177
Signal Contact (Receiver)
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)
-
Product
Signal, Patchcord, Receiver, 36", TriPaddle, USB 2.0 Wire, to USB Type A Plug (1.5 Amps)
7-104872596-036
Signal Patchcord
Signal, Patchcord, Receiver, 36", TriPaddle, USB 2.0 Wire, to USB Type A Plug (1.5 Amps).
-
Product
PXI Solid State Multiplexer, 30 Amp, Single 6-Channel
40-667A-012
Multiplexer Module
The 40-667A-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI/PXIe Power Relay Module, 25xSPST, 5 Amp, 50-pin SGMC Connector
42-153-003
Relay
The 40/42-153-003 is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A. User connection is via a 50-pin SGMC male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 1m, 250 Port
A500RMR-500RMR-4B100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
Product
PXI 2 Amp Multiplexer, Dual 4-Channel, 4-Pole
40-635A-107
Multiplexer Module
The 40-635A-107 is a dual 4-channel, 4-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Signal, Patchcord, ITA, 72", TriPaddle, 24 AWG Twisted Pair, Single Ended ( 3 Amps)
7-103424000-072
Signal Patchcord
Signal, Patchcord, ITA, 72", TriPaddle, 24 AWG Twisted Pair, Single Ended ( 3 Amps).
-
Product
1000A Amp AC/DC True R.M.S
DCM-2606
-
Digital Clamp-on Meters. AC/DC current up to 1000A. AC/DC voltage up to 1000V. Display hold function. True-RMS reading. Diode test
-
Product
500-Pin SEARAY Connector, Male With Backshell, 2 Amp, 250 Port
C500RMR-4SB-5C
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Power, Patchcord, ITA, 36", High Power, 2 AWG, Single Ended (150 Amps)
7-222902000-036
Power Patchcord
Power, Patchcord, ITA, 36", High Power, 2 AWG, Single Ended (150 Amps).
-
Product
PXI 19 x DPST Reed Relay 2 Amp
40-136-212
Relay
The 40-136-212 19xDPST reed relay module is part of our range of medium power, general purpose relay modules which are capable of switching voltages up to 200V and current up to 2A.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Ferrules, 2 Amp, 0.5m, 250 Port
A500RMR-F-5C050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
PXI 2 Amp Multiplexer, Quad 16-Channel, 1-Pole
40-635A-008
Multiplexer Module
The 40-635A-008 is a quad 16-channel, 1-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 1 Amp, 1m, 500 Port
A500RMR-T-0A100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 0.5m, 250 Port
A500RMR-05F050D5C050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Twin Female
610138100
Signal Contact (Receiver)
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Twin Female
