Optic Heads
-
Product
32 Channel Optically Isolated Digital Card
104-IDIO-16 Family
-
The Model 104-IDIO-16 is a 32-channel PC/104 utility board featuring 16 optically isolated inputs and 16 optically isolated solid state outputs. The isolated, non polarized inputs may be driven by either DC sources of 3-31V (or higher by special order) or AC sources at frequencies of 40Hz to 10KHz. Optically isolating the digital inputs from each other, and from the computer, assures smooth, error-free data transmission in noisy, real-world environments. The 16 input channels are available via a 34-pin IDC type header. The fully protected solid state outputs, capable of sourcing 2A each, are inherently more reliable than electromechanical relays and give system architects a more robust product to design with. The solid state outputs are available via a 50 pin IDC type header.
-
Product
Optical Time Domain Reflectometer OTDR
BD300
-
Shanghai Baudcom Communication Device Co.,Ltd.
BD300 Optical Time Domain Reflectometerhas excellent dead zone performance and wide dynamic range. Combined with the visualfault locator, the OTDR can easily find the breaks, bends, splices, faultyconnectors, and other causes of signal loss.
-
Product
Optical Test Equipment Series
-
Optical Test Equipment used to measure the measured elements of the form tolerance, such as position, concentricity, profile, roundness and straightness, size, etc...
-
Product
Measuring System for Assessment of Optical Radiation Safety
IEC62471
-
The system is designed especially for the determination of optical radiation hazard exposures specified in IEC62471, such as actinic UV hazard exposure for the skin and eye, near-UV hazard exposure for the eye, retinal blue light hazard exposure, retinal thermal hazard exposure, thermal radiation hazard for eye and skin, for LED products, UV-Lamps, lighting sources, luminaires and etc.
-
Product
Fiber Optic Visual Fault Finder
VFF5
-
Used to verify continuity, test and find breaks in fibre links, locate pinched fibre strands in termination cabinets, or anywhere fibre optic cables are terminated and subject to mechanical damage.
-
Product
High Speed Free Space Optical Detectors
-
High speed optical detectors use special photodiodes with high speed electronic circuits to convert fast optical pulses to electrical signals for measurement. Unlike our optical receivers, these detectors do not include a transimpedance amplifier.
-
Product
Optical Test Instruments
OptiSpheric® & Spherometer
-
TRIOPTICS' OptiSpheric® and Spherometer are the classic optical test systems for spherical lenses that can be found in virtually any optical manufacturing process. While the Spherometer is used for the tactile determination of lens radii, OptiSpheric® systems provide contactless measurement of effective focal length, back focal length, flange focal length, MTF on axis and the radius of lenses. Specific upgrades allow determining centration errors and angles on plane surfaces. Systems for testing IOLs in compliance with EN/ISO 11979 form a class of their own. OptiSpheric® IOL R&D is preferably used for measuring single lenses while OptiSpheric® IOL PRO 2 is designed for the fully automated IOL measurement in serial production.
-
Product
Standard In-door Forward Optical Receiver
ONR-8636
-
Hangzhou Huatai Optic Tech. Co., Ltd.
ONR-8636 with standard configuration is a type of high index and universal in-door forward optical receiver. It adopts Philip optical receiving module. End-grade adopts power-doubling module. Optical connectors and RF connector can be installed at the front panel or back panel.
-
Product
Fiber Optical Cable Testers
-
Encompasses the processes, tools, and standards used to test fiber optic components, fiber links, and deployed fiber networks.
-
Product
High Accuracy Fiber Optic Sensors
FS01
-
Compact & simple operation. New 12-bit concurrent CPU. 20-s response speed. Multiple calibration methods. Wire-Saving 0-line or 1-line connection
-
Product
Attitude And Heading Reference Systems
AHRS
-
Beginning in 2001, Inertial Labs began manufacturing its MEMS-based, IP-67 sealed, MIL-STD-810G qualified, multiple interfaces and COM ports Attitude and Heading Reference System in response to the need for an inclusive and price competitive Antenna Pointing, Aiming, and Stabilizing applications. Each INS contains an Inertial Labs-developed tactical or industrial-grade inertial measurement unit (IMU) and an Inertial Labs-manufactured high-precision Fluxgate magnetometer.
-
Product
Semiconductor Optical Amplifier
SOA
-
Amonics SOA is a polarization maintaining optical amplifier with high fiber-to-fiber gain. It is designed for transmitter applications to increase optical launch power to compensate for the loss of other optical devices. The benchtop version incorporates a user-friendly front panel housing a LCD monitor display, key switch, power control knob and optical connectors. RS232 computer interface is also equipped on the rear panel. 1MHz with 10ns pulse width intensity modulation is available. The OEM module version is an ideal building block for OEM system integration, especially in optical communication network and CATV applications. It requires only a single +5V power supply.
-
Product
Optical Displacement Measurement Systems
ODS Series
-
The optical displacement measurement systems of the ODS series are specially designed for measuring the ultrasonic vibration displacement at bond tools of wire & flip-chip die bonders. The systems are highly accurate and very easy to use. That makes it the perfect tool for displacement based calibration of ultrasonic bond machines.
-
Product
Optical Radiation Safety Test
EN62471-C
-
IEC62471-2006(CIE S009) Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
Product
CATV RF Optical Receiver
L-RF-MN-RX
-
The QuestTel''s L-RF-MN-RX module optical receivers are versatile, low-cost and compact optical receivers for use in HFC fiber applications. It is perfect solution for the transport and distribution of CATV RF signals over fiber optic cable. The L-RF-MN-RX module housed in a small housing and have adjustable RF output level. May be used as a hand held device for testing, or placed at a customers premise for the reception of cable television services. The Receiver is designed to operate with a very low optical input level between the range of +3dBm to -12dBm.
-
Product
RS422 Mode SI-module With Optical Isolation And RTS/CTS
MX422-PEP
-
RS422 mode SI-module with optical isolation and RTS/CTS
-
Product
Optical & Vision Systems
-
Usually made up of every component that is needed to acquire and analyze an image in order to perform the intended task.
-
Product
Fiber Optic Inspection Microscope
80760
-
The Miller 200x Microscope helps inspect fiber optic connectors quickly and easily. Its ergonomic design and built-in features make it ideal for field and lab use. The microscope features a pressure-activated on/off switch, focusing wheel, eyepiece, auxiliary white LED light source rated for 100,000 hours, adapter tip for inserting ferrule and battery compartment.
-
Product
Outdoor AGC Optical Node
SR812B
-
Hangzhou Softel Optic Co., Ltd.
SR812B optical receiver is our new development products that especially used in CATV network. The pre-amp adopts GaAs MMIC amplify module and the post-amp adopts GaAs power doubler amplify module .Support specifical attenuation and equalization inserts if you want.Or as per customer, adopts other module.With optimization design and plentiful technical experience that made this equipment with high performance specification. It is a ideal model for CATV network.
-
Product
Four outputs FTTB CATV optical receiver
B9428
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai B9428 product series, 47~862MHz operate bandwidth, output level Vo=88dBμV ( Pin=-2dBm ), suitable for FTTP optical fiber access network, which is a low power consumption, high performance, and excellent cost performance RFTV broadcast network ONU(Optical network unit). This series of product adopts high sensitivity receiving tube and Huatai special low noise matching circuit Under 3.8% modulation, when transmitting in full channels and with receiving power of -10dBm, the CNR can still reach high index of 45dB. Therefore, if adopting B9428, it is only need very low optical power to reach 45dB CNR required by the user.
-
Product
Optical Spectrum Analyzer - MATRIQ
1000 Series
Spectrum Analyzer
The OSA 1000 Series provides grating-based spectral test and measurement. It is an excellent fit for the testing of optical sources, amplifiers, transceivers and passive optical components.The OSA is available in a range of wavelengths for different applications, so you pay only for the capabilities you need.
-
Product
Fiber Optic Measurement Systems & Sensors
-
MTI Instruments offers large measurement range and standoff distance fiber-optic measurement sensors and probes that provide ultra sensitive linear output response. Our modular (interchangeable) non-contact fiber optic sensors systems have dual channel that enables the user to make simultaneous measurements. Our fiber optic probes are designed to automatically compensate large changes in reflectivity making it possible to monitor dynamic reflectance of up to 100:1 making it ideal for measuring vibration of ultrasonic horns, modal analysis of disk drive suspension, displacement and timing of fuel injectors and lateral motion measurements.
-
Product
Module Accessory Kit, Quantity 39 0-80 x .250" Socket Head Cap Screws
510109300
Accessory Kit
Module Accessory Kit, Quantity 39 0-80 x .250" Socket Head Cap Screws.Used with 90 Series modules p/n's : 510104120, 510104123, 510104267 and 510104270.
-
Product
Industrial Temperature Head Sensors
-
A selection of Head Mounted Industrial Temperature Sensors for many applications with RTD / PRT varieties, Hygienic and Heavy Duty probes.
-
Product
Module Accessory Kit, Quantity 26 2-56 x .375" Flat Head Slotted Screws
510109306
Accessory Kit
Module Accessory Kit, Quantity 26 2-56 x .375" Flat Head Slotted Screws
-
Product
Optical Communication Parts
-
Adamant Namiki Precision Jewel Co Ltd.
Zirconia ferrule sleeve is an important part in optical fiber communication and is the basic product of our optical communication parts. We have developed an optical communication parts part of hasad developed based on grinding and bearings. Offer Optimum Performance And Quality For Each Type Of Optical Fiber, Optical Connector And Optical Device. We Also Offer Pin Gauges And Ring Gauges For Measuring Precise Dimensions Indispensable To Our Quality Assurance . These Gauges Have Little Wear, Good Compatibility With Ferrules And Sleeves, Zirconia , sapphire and cemented carbide are used as materials.Various Optical Connectors And Adapters Using Ferrules And Sleeves, Follow The Long History FC And SC Connectors, MU , LC Connectors Are Also Available. In Particular, LC Connectors Are Deployed In A Wide Lineup With Adapters. In The Field Of Optical Devices, We Provide Codes Master , Various Patch Cords , Conversion Adapters That Connect Different Types Of Connectors, Attenuators And Terminators That Provide Stable Characteristics, Which Are Manufactured Using The Ferrule Quality Of Our Own Manufactured Parts We Will. We Also Offer Parts For Optical Devices SuchAs Fiber Array Used For Connection Of PLC, AWG And Others. In The Field Of Optical Modules, SC And LC Receptacles , Fiber Stub, Pigtail Fiber And Other Optical Module Parts, And Now We Have Provided TOSA, ROSA And Other Optical Module Manufacturing Consignment Services. We Also Deal With Various Lensed Fibers Which Processed Fiber Tip With High Precision . In Addition, We Also Flexibly Deal With Precision Component Processing Used In Optical Communication Field, Special Specification Ferrule, Sleeve Etc. Please Contact Us.
-
Product
Isocratic Pumps - Single Headed, Positive Displacement Piston Pumps
ReaXus MX Class
-
The economical MX Class consists of single-headed, positive displacement piston pumps incorporating additional features for challenging applications. With pressure capability up to 5,000 psi, the MX Class can be used in both analytical and smallscale preparative HPLC separations. Further applications include demanding metering and dispensing, as well as Sample Injection, Infusion, or Cone Wash for Mass Spectrometers. Standard fluid path material is Stainless Steel.Features include available pressure monitoring with automatic pressure compensation, Pulse Dampener, integrated Prime-Purge Valve, interactive keypad control, and complete PC control and status through RS-232 and Micro USB 2.0 ports. Requiring minimal bench space for the performance, the MX Class will easily integrate into most workspaces.
-
Product
Fiber Optic Sensor Systems
-
Fraunhofer Institute for Telecommunications
Fiber-optic and photonic measuring systems open up innovative measuring and control technology concepts for a wide variety of applications. They play a major role in optimizing energy efficiency and are important technological innovation drivers for new and future-oriented markets.In the Department of Fiber Optic Sensor Systems of the Fraunhofer Heinrich Hertz Institute, the focus of application-oriented research is on the development of a new generation of photonic sensors. These are characterized by extreme miniaturization, high network and communication capability as well as extremely low power consumption or even a self-sufficient power supply.In the Department of Fiber Optic Sensor Systems at the Fraunhofer Heinrich Hertz Institute is focused applied research on the development of a new generation of photonic sensors. These are characterized by extreme miniaturization, high network and communication skills as well as an extremely low power consumption, or even a self-sufficient energy supply.
-
Product
Fiber Monitoring System for Optical Networks
-
Detecting serious physical network infrastructure issues like accidental fiber cuts, intrusion attempts, and malicious tampering has never been easier than utilizing this Fiber Monitoring System available from M2 Optics. The first solution approach in the industry that was designed to minimize monitoring costs on a per-fiber basis, all the hardware and software are integrated into a single low-profile chassis for fast deployment to cover your critical links.
-
Product
Optical Components & Transmission Simulation Software
VPIphotonics Design Suite
-
VPIphotonics Design Suite™ embeds expert knowledge from our component and transmission design tools in one shared, flexible software environment to support requirements in design, analysis and optimization providing you with the most powerful numerical algorithms tailored for your applications.
