Showing results: 121 - 135 of 270 items found.
-
-
Extech 601500 -
Extech Instruments Corporation
The Extech 601500 is a Standard pH Electrode and BNC combination. This electrode includes a long 1 m (39 in) cable for hassle free use, BNC connector, and storage solution bottle. Product has a 6 month warranty.
-
Texas Co.
Rngs around the BNC input sockets that allow the attenuation factor of attached probes to be detected by the scope.
-
Telewave Inc.
Standard connectors: RF In / Out - N-Female, UHF optional. Sampling Ports - RCA-Female, BNC optional.
-
Model: 137B21B -
PCB Piezotronics, Inc.
Quartz, free-field, ICP blast pressure pencil probe, 1000 psi, 1 mV/psi, BNC connector
-
DTA-112 -
DekTec Digital Video B.V.
Cost-effective variant of DTA-115 with 75-Ω BNC main output and support for ATSC, QAM-A/B/C and DVB-T.
-
72-6784 -
Tenma
The 72-6784 is a typical 0 to 14pH Probe with epoxy body, BNC connector. It is used with pH meter 72-6783 model.
-
LK-468A -
Lucktech Electronics
Test Function for cale with RJ11,RJ12 RJ45&BNC plugs.Tests continuity, assignments, paring and shielding line/voltage detection main device.
-
21-8569-00 -
LANTAC Techtronics Co. LTD
Open / Short / Misswiring test?BNC / RJ45 each pin connected display?No wire or termination?Isolation Resistances 50K ohms test
-
SMT-FMC510L -
Sundance Multiprocessor Technology Ltd.
The SMT-FMC510L is an FMC module with a low pin count connector (LPC). It is primarily designed to attach to the EMC2-DP FMC PCIe104 carrier board and provide analogue video and serial interfaces. Connectivity is via BNC connectors on the main FMC PCB, BNC connectors on an adaptor PCB, and two 20-way latching DIL pin headers. The adapter PCB is optional and only required if interfaces other than analog video are needed.
-
72-6783 -
Tenma
The 72-6783 is a 0 to 14pH Meter with 12.5mm LCD display. Any combination of pH electrode and male BNC connector can be used. pH meter included with battery.
-
PHCT45 -
Pyle Audio Inc.
This Pyle network cable tester checks RJ45 and BNC network cables for continuity and correct polarity. LEDs show the status of each pin. , perfect for the IT guy on the go.
-
EXR2RACK -
Keysight Technologies
The EXR2RACK rack mount kit includes all parts needed to mount your Infiniium EXR-Series oscilloscope in an 8U open frame rack and includes a Support tray, Trim plates, BNC connectors to be inserted into the bottom trim plate, black rubber stoppers to plug holes in bottom trim plate if the hole is not being used for a BNC connection, Two track rails, Two clamp brackets, both right and left Top clamp brackets, screws, and nuts.
-
DCD-24 -
Brainstorm Electronics Inc.
The DCD-24 is both a Word Clock Generator and a Distributor, using exceptional jitter reduction technology. With 24 BNC outputs the DCD-24 sends accurate Word Clock throughout an installation.
-
Mini-Circuits
RF/microwave interconnect and precision test cables for 50-Ohm and 75-Ohm systems from DC to 67 GHz with a wide selection of connectors including SMA, N-Type, F-Type, BNC, and 2.92mm!